可闻声波检测与空气中声速的测定

描述了用改进的声波探测器在空气中测定声速的方法。     

利用积分算子方程的小波－矩量法分析频率选择反射面

小波－矩量法以小波基作为矩量法中的基函数，通过Ｇａｌｅｒｋｉｎ法可以获得很稀疏的阻抗矩阵，用迭代法求解时可减少计算机内存和计算时间。该文以有限尺寸的频率选择反射面为例，用小波－矩量法分析散射特性和电流分布，着重讨论了阻抗矩阵的稀疏化程度对计算精度的影响。结果表明，当非零元素仅为１０％时，仍能达到满意的精度，因此小波－矩量法不失为分析电大尺寸问题的一种有效方法     

电能质量问题及对策

概述了电能质量问题的产生及日益引起关注的原因，介绍了国际电工委员会(IEC)和电气与电子工程师协会(IEEE)对电能质量的定义，并针对电能质量问题提出了具体对策。     

Toda-Lattice系统的显式精确解

利用双曲函数方法，研究了具有广泛、深刻物理背景的Toda-Lattice系统，得到了它的显式精确解，这种方法也适用于求解其他离散的非线性方程(组)。     

计算力学量平均值的一种方法

论述了量子力学中的海尔曼-费曼定理的内容和应用范围，重点阐明应用海尔曼-费曼定理求力学量平均值的方法，并探讨了粒子在中心力场中的运动．     

基于DSP的电子耳蜗语音处理器的研制

电子耳蜗是一项正在迅速发展的聋人康复新技术，其关键是要研制出可靠、灵活、价格低廉的产品。首先介绍电子耳蜗的原理及其进展，然后介绍基于TMS320VC5402 DSP处理器的电子耳蜗语音处理器。实验证明：基于DSP的电子耳蜗系统可以按照患者的实际情况灵活选择各种语音处理方案，并能方便实现语音预处理、噪声抑制和对应各电极的频谱阈值调整，是一种比较好的系统结构。     

Study on End Milling Generation Surface Model and Simulation in View of Main Axle s Tolerance

In accordance with the relative movement between end-milling cutter and workpiece surface, a theoretical generation model for milled surface was established with the movement error of principal axle considered. Then the milled surfaces under various cutting condition were simulated, the results of which showed that end milled surfaces were of “vaulted profile“, heights of surface irregularty at various points to be different with maximum value in the middle and smaller at both sides, the difference were ...     

电气试验中两个异常负值现象分析

介绍了在电气试验中遇到的两个奇异负值现象，探讨了造成这些现象的原因，并说明在工程实践中成功的解决方法。归纳了电气试验中消除干扰对电气试验结果影响的几点工作经验。     

Preparation and properties of the SmOx/Rh(100) model surface

The preparation of SmOx/Rh(100) and CO adsorption on this model surface have been investigated with Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and temperature programmed desorption spectroscopy (TDS). The oxygen adsorption on the SmRh alloy surface leads to the aggregation of Sm on the surface. The thermal treatment of this oxidized surface induces the further agglomeration of SmOx on the Rh(100) surface. Compared with CO TDS on the clean Rh(100) surface, three additional CO desorption peaks can be observed at 176, 331 and 600 K on the SmOx/Rh(100) surface. The CO desorption peak at 176 K may originate from CO adsorbed on SmOx islands, while the appearance of the CO adsorption peaks at 331 and 600 K, depending on the oxidation state of Sm, is attributed to CO species located at the interface of SmOx/Rh(100).