全文获取类型
收费全文 | 1303篇 |
免费 | 63篇 |
国内免费 | 54篇 |
专业分类
系统科学 | 35篇 |
丛书文集 | 22篇 |
教育与普及 | 5篇 |
理论与方法论 | 1篇 |
现状及发展 | 5篇 |
综合类 | 1351篇 |
自然研究 | 1篇 |
出版年
2024年 | 4篇 |
2023年 | 14篇 |
2022年 | 24篇 |
2021年 | 28篇 |
2020年 | 19篇 |
2019年 | 22篇 |
2018年 | 27篇 |
2017年 | 43篇 |
2016年 | 35篇 |
2015年 | 51篇 |
2014年 | 53篇 |
2013年 | 63篇 |
2012年 | 86篇 |
2011年 | 87篇 |
2010年 | 56篇 |
2009年 | 66篇 |
2008年 | 57篇 |
2007年 | 84篇 |
2006年 | 69篇 |
2005年 | 65篇 |
2004年 | 66篇 |
2003年 | 45篇 |
2002年 | 50篇 |
2001年 | 28篇 |
2000年 | 32篇 |
1999年 | 35篇 |
1998年 | 24篇 |
1997年 | 29篇 |
1996年 | 22篇 |
1995年 | 23篇 |
1994年 | 18篇 |
1993年 | 17篇 |
1992年 | 15篇 |
1991年 | 18篇 |
1990年 | 13篇 |
1989年 | 13篇 |
1988年 | 9篇 |
1987年 | 6篇 |
1986年 | 3篇 |
1985年 | 1篇 |
排序方式: 共有1420条查询结果,搜索用时 469 毫秒
211.
采用一维设计与三维数值模拟分析相结合的方法,对某动车组轴流冷却风机进行气动设计,并分析研究了等环量指数对轴流冷却风机气动性能的影响.根据一维设计的几何参数进行三维建模;再利用NUMECA软件对所设计风机进行深入数值模拟分析及结构优化改进;最后,选取最优方案加工样机并进行性能试验.试验结果表明:该轴流冷却风机的整体气动性能较优,与原设计相比有较大改善,特别是效率提高了近3%,叶轮进、出口流场较原机叶轮也更加稳定.该国产化风机与同类型某进口风机相比性能更优. 相似文献
212.
利用有限元耦合场数值模拟计算方法,对大直径棒材穿水冷却过程进行了三维非稳态数值模拟,研究了冷却水流量对冷却效果的影响规律,并分析了决定冷却水流量的两个因素———冷却器入口截面积及冷却水流流速对冷却效果的影响程度.模拟结果表明:当流量相对较小时,流量的改变对冷却效果的影响较大;当流量增大到一定值后,随着流量的继续增大,对冷却效果的影响逐渐减小;冷却水流流速对冷却效果的影响程度大于冷却器入口截面积. 相似文献
213.
以混合动力车用镍氢电池为研究对象,利用计算流体动力学分析软件对现有电池组的散热结构进行了流场和温度场的仿真分析,研究结果表明现有电池组的温度场均匀性较差.通过调整挡板及电池的位置、改变电池倾斜角度和电池的间距、施加挡风结构、包覆保温层等方法改善了电池组冷却气流分布和电池组温度场均匀性,其中包覆保温层的效果最好.为混合动力车用镍氢电池热管理的设计提供了依据. 相似文献
214.
This paper established an on-line monitoring model for fouling resistance of cooling water based on heat transfer theory,which was mainly applied to the fouling resistance test for condenser of chiller in operation,and the test requirements were presented.It proves that the load ratio of chiller has big influence on the test re-sult,and the best load ratio for test is the range of 80%~100%.A case has been executed to validate the mod-el's feasibility. 相似文献
215.
Wang Ruzhu 《中国工程科学》2009,7(2):91-96
This paper mainly shows the demonstration of solar air conditioning systems in China, which includes LiBr-H2O absorption cooling, silica gel-water adsorption chiller, desiccant cooling and hybrid integrated energy systems for buildings. The match of solar collector types and chiller types have been discussed and suggested. 相似文献
216.
水管冷却混凝土温度场离散算法网格密度研究 总被引:1,自引:1,他引:0
水管冷却混凝土温度场离散算法精度较高,但水管周围温度梯度较大,必须布置较密的网格,计算量较大.为了同时满足计算量和工程精度的要求,需研究水管周围的网格密度.建立3个不同网格密度的含水管混凝土块有限元模型,对每一个模型都分别赋以3种不同的管壁放热系数进行计算.计算结果对比表明,对于大坝目前常用的塑料冷却水管,将水管周围混凝土网格加密1层即可满足工程需要;对于高导热性能塑料水管或金属水管,建议加密2层. 相似文献
217.
To reduce surface depression of a bloom, the primary cooling intensity was decreased, and the water distribution of mold wide and narrow faces was optimized. The length of secondary cooling zones and the specific water flow were increased, and the water flow distribution among the secondary cooling zones was adjusted to eliminate central defects, such as center looseness, central segregation, and center line cracks. The operation showed that the proportion of surface depression decreased from 37.22% to 2.87%, whereas the proportion of center looseness for 〈1.0 increased from 79.71% to 90.70%, the proportion of central segregation for 〈0.5 increased from 1.45% to 44.19%, and the proportion of center line cracks that are free increased from 39.13% to 62.79%. The qualified blooms are delivered to produce 310 Z-beam, whose yield strength is greater than 450 MPa. 相似文献
218.
结合实际工况参数,采用有限元分析工具ANSYS软件,研究了辊式淬火机淬火冷却系统集管进水方式、均流结构等对喷水系统流量分布的影响.分析表明,中间进水形式的集管可形成一定的中凸水量分布,易于获得较为合理的水量分布;集管内的隔板阻尼可较明显地改善喷嘴射流速度分布的均匀性.并以自主开发的淬火机缝隙喷嘴结构为例,分析了缝隙射流的流动特性,模拟表明,所开发的缝隙喷嘴结构出口射流沿喷嘴长度方向的速度分布较为均匀,紊动度小,有利于保证淬火钢板的冷却均匀性.将开发的淬火冷却系统应用于生产实践,取得较好的使用效果. 相似文献
219.
Nd8Fe86B6铸锭在非平衡凝固条件下,当冷却速度比较小时,相的组成为Nd2Fe,4B+α-Fe+富B相.随着冷却速度的增大,富B相消失,相的尺寸由大变小,且分布不均匀.揭示了由于母合金在各个部位成分的不均匀性,导致‘后续工艺中颗粒长大的可能性的原因,并提出了一些可能的改进措施. 相似文献
220.
论述了板坯连铸二次冷却技术研究的进展,针对板坯连铸工艺及钢水凝固过程,建立了板坯凝固传热通用数学仿真模型。按照连铸工艺要求及铸坯质量准则,应用VB6.0开发了板坯连铸二次冷却计算机通用仿真软件。通过软件的模拟仿真计算,对连铸工艺参数进行优化设计。软件界面直观友好,准确度高。 相似文献