激光重熔高速电弧喷涂FeNiCrAl涂层的组织与断裂韧性

采用激光技术对高速电弧喷涂FeNiCrAl涂层进行重熔处理.分析了重熔前后涂层的组织结构、物相成分、显微硬度与断裂韧性.结果表明:重熔后,喷涂层片层状堆叠结构与孔隙得到消除,组织结构变得均匀、致密,涂层与基体由机械结合变为冶金结合.喷涂层物相主要有α-Fe及金属间化合物AlFe₃,AlFe和Al_0.4Fe_0.6,重熔后,生成了新相Fe-Cr,［Fe, Ni］固溶体和碳化物NiC_○x.重熔后涂层的平均显微硬度为7.79GPa,约为基体硬度(2.5GPa)的3倍,约为喷涂层硬度(6.0GPa)的1.3倍.载荷为4.9,9.8N时,喷涂层的压痕尖头出现裂纹,涂层平均断裂韧性为1.20MPa·m^1/2,载荷为2.94~9.8N时,重熔后涂层的压痕尖头均没有观察到裂纹.     

Multi-threshold second-order phase transition in laser

We present a theory of the multi-threshold second-order phase transition,and experimentally demonstrate the multi-threshold secondorder phase transition phenomenon.With carefully selected parameters,in an external cavity diode laser system,we observe secondorder phase transition with multiple(three or four) thresholds in the measured power-current-temperature three dimensional phase diagram.Such controlled death and revival of second-order phase transition sheds new insight into the nature of ubiquitous secondorder phase transition.Our theory and experiment show that the single threshold second-order phase transition is only a special case of the more general multi-threshold second-order phase transition,which is an even richer phenomenon.     

双端热透镜Z型固体激光腔图解分析

采用传播圆图解方法研究了具有双端热透镜的Z型折叠固体激光腔的工作特性,得到了谐振腔各腔臂中的光模参数bt1,bt2,b2及光斑尺寸wt1,wt2,w2随激光介质的热动力参数1/ft1及1/ft2的变化关系;结果表明通过合理选择参数可对腔的热稳定范围及基模光斑尺进行调控,其关键参数是对称的第1、3臂的长度l01 f1(或l02 f2),其值越小,腔的热稳定区越宽,同时激光晶体处的基模光斑越小.第2臂中的参数δ对热稳区宽度没有明显影响,但δ值越大,对应的光斑半径wt1及wt2也越大.     

基于陀螺星光加激光交会雷达的相对姿态确定

针对编队飞行中从飞行器与主飞行器的相对姿态确定问题,提出了基于扩展卡尔曼滤波(EKF)的相对姿态确定方法. 采用修正罗德里格参数(MRPs)作为姿态描述参数避免奇异点. 姿态敏感器采用陀螺 星敏感器 激光交会雷达的配置模式,并且结合相对姿态动力学方程得到相对姿态确定的状态方程,建立起相对姿态确定的EKF模型. 仿真实例表明,EKF状态能在最慢300 s内收敛,MRPs的估计误差在10-5范围以内,该方法正确有效.     

红色激光器在节子厚板材合理截断中的应用

在对厚板材加工中存在的合理截断问题进行分析的基础上,以提高主产出材率为目的,提出了解决其现场操作的方法——采用红色激光器确定截断位置,并利用生产实际进行加工实验加以论证.实验表明:红色激光器对节子厚板材在截断时的主产出材率的提高效果十分显著.     

一种新的解锁螺栓分离时间测试方法

基于激光位移传感器测试解锁螺栓分离时间的思想,设计一种新的解锁螺栓分离时间测试方法,并设计了相应的测试系统,其测试不确定度为0.184%.通过试验得到新方法测得解锁螺栓分离时间平均值14.74ms,传统的通-断靶线法测得分离时间平均值14.60ms,三次试验均值相差0.14ms.结果表明,新方法不仅能直接有效地测试解锁螺栓分离时间,还能间接地表征解锁螺栓的分离速度、冲击加速度以及分离冲量等分离特性参数.     

Photonic integrated technology for multi-wavelength laser emission

We summarized the design, fabrication challenges and important technologies for multi-wavelength laser transmitting photonic integration. Technologies discussed include multi-wavelength laser arrays, monolithic integration and modularizing coupling and packaging. Fabrication technique requirements have significantly declined with the rise of reconstruction-equivalent-chirp and second nanoimprint mask technologies. The monolithic integration problem between active and passive waveguides can be overcome with Butt-joint and InP array waveguide grating technologies. The dynamic characteristics of multi-factors will be simultaneously measured with multi-port analyzing modules. The performance of photonic integration chips is significantly improved with the autoecious factors compensation packaging technique.     

Compact fiber-optic diode-laser sensor system for wide-dynamic-range relative humidity measurement

A compact fiber-optic diode-laser sensor system for measuring relative humidity is studied. In such a system, a distributed feedback laser lasing near 1877 nm is used as light source while a high-precision Pt resistance as temperature sensor, an accuracy of 0.1% relative-humidity can be achieved. The laser sensor system is able to lock to the absorption peak and calculate the density of water vapor without any additional reference measurements. Using programs built in to the microcontroller unit, the laser system can switch functions between direct measurement at high density and second-harmonic detection at low density. The system can switch between the two modes automatically and work in a wide dynamic range.     

激光辐照移动平板温度场分布的有限元分析

基于热传导理论,采用有限元方法建立激光辐照无限长移动平板表面激发瞬态温度场的三维模型,用以研究移动平板上下表面瞬态温度场.考虑板材料的热物理参数依赖于温度、板表面的热辐射及对流等因素,计算了上述因素及移动速度对温度场的影响,并进一步讨论了激光半径对温度场的影响.数值结果表明:激光辐照移动平板后,在材料中将产生准稳态温度...     

基于结构光立体视觉的激光再制造工件的测量

为了实现激光再制造工件的快速准确测量,提出了1套与激光再制造机器人耦合的视觉系统.该视觉系统由2个摄像机、1个激光投射器和计算机组成.摄像机和激光投射器组成扫描测头,由6自由度机器人手持实现多视角扫描.并自动完成数据拼接,消除‘死角'.首先,通过MATLAB编程完成系统标定,分别标定出单目摄像机内外参数矩阵,双目相机关...