Effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of B–Y modified silicide coating

B–Y modified silicide coatings were prepared on Nb–Si based alloy by pack cementation at 1300 ℃ for 10 h. The effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of the coatings was investigated. The results show that the four coatings have similar structures, which possess a(Nb,X)Si_2 outer layer and a(Nb,X)_5Si_3 transitional layer. Y_2O_3 content in the pack mixtures has an obvious effect on the Si content in the coating. The mass gains of the coatings prepared with 0.5, 1, 2 and 3 wt% Y_2O_3 in pack mixtures are 2.33, 1.96, 2.05 and 2.86 mg/cm~2 after oxidation at 1250 ℃ for 100 h, respectively. The coating prepared with 1 wt% Y_2O_3 exhibits the best oxidation resistance due to the formation of a dense glass-like borosilicate scale.     

Atomic-scale segregation behavior of Sn/Ti and O at Σ3[11¯0](111) grain boundary in niobium

First-principle calculation was performed to illustrate the atomic arrangement and segregation behavior of Sn/Ti and O in View the MathML source grain boundary, and the interaction of oxygen interstitials with Sn/Ti atoms on the grain boundary was studied. The analyses on the segregation energies and geometric positions, and the electron densities show that Sn, Ti and O atoms segregate at the Σ3 grain boundary. And the preferred segregation sites of the impurities at View the MathML source were determined. When Sn segregates at grain boundary plane, the O atom prefers to the bulk-like site and shows no segregation tendency at grain boundary, whereas the segregated Ti atom can slightly enhance oxygen segregation at the grain boundary.     

热处理对镍基合金涂层与基体结合界面的影响

通过热浸镀法在普碳钢表面成功制备镍基合金涂层.为了提高镍基合金涂层与钢基体之间的结合强度,对镀有镍基合金涂层的基体进行了热处理.研究了热处理前、后结合界面处的显微组织和力学性能.结果表明,与热处理前相比,热处理后界面附近的涂层中析出物长大,界面处存在不连续块状铁的硼化物,界面两侧镍、铁互扩散距离增加,靠近界面的过渡带由5～8μm变为20μm.热处理前、后涂层均由γ-(Fe,Ni)、CrB、Cr2B和Cr3C2等相组成,过渡带相组成为γ-(Fe,Ni)、微量CrB和Fe23(C,B)6.热处理后,显微硬度由界面向涂层内逐渐增加,界面结合强度由140MPa提高到200MPa.     

连续柱状晶组织BFe10-1-1合金的电化学腐蚀性能

采用线性极化、电化学阻抗谱等电化学方法研究了连续柱状晶组织BFe10-1-1合金在3.5%（质量分数）NaCl溶液中的耐蚀性能,并与普通铸造多晶组织BFe10-1-1合金进行了对比.极化曲线测试结果表明,两种合金具有相似的电化学行为,极化曲线都包括活性溶解区、活化-钝化转变区和极限电流区,但连续柱状晶组织合金腐蚀速率小于普通铸造多晶组织合金,主要是由于连续柱状晶组织BFe10-1-1合金的微观偏析程度较小,能有效避免枝晶间局部腐蚀的发生.电化学阻抗谱测试结果也表明,该合金的电荷传递电阻和腐蚀产物膜电阻均大于普通铸造多晶组织合金,具有更高的耐蚀性.     

X射线光电子能谱检测热喷涂锌铝合金防腐性能的研究

锌铝合金可用作为风力发电装置的防腐材料.采用X射线光电子能谱（XPS）研究了由热喷涂方法制备的不同含量铝锌合金制得的TJPTZA1^#、TJPTZA2^#、TJPTZA3^#和TJPTZA4^#合金的防腐蚀性能,探究了合金与基体界面处的物质成分.使用能谱检测手段探索了界面处的元素成分及其含量,从而为以上合金的防腐性能研究提供依据.     

A356.2铝合金生产过程中的设备管理效益

介绍了在当前铝加工行业较为困难的情况下,A356.2铝合金生产线的设备选型,提出了几种创造效益的新思路,论证了设备管理不再是狭义上的设备技术管理,而是更广义的生产力管理.设备管理需根据市场经济要求,不仅为生产服务,更要为提高企业的经济效益服务,为提高产品质量、降低能耗、控制污染、减少成本和占领市场服务.     

Rapid reductive degradation of azo dyes by a unique structure of amorphous alloys

An Fe-based amorphous alloy was found to significantly enhance the reductive degradation of an azo dye in aqueous solution. The surface-area normalized rate constant was up to 2.0 L m-2 min-1 at room temperature,an order of magnitude larger than any previously reported value. The activation energy of the degradation process was calculated according to the Arrhenius equation,and a much lower value than those previously reported was obtained. Valence band measurement indicated that a depressed valence band maximum and a widened empty band were established in the amorphous ribbon. The unique structure of the amorphous alloy is important-it may reduce the activation energy of the degradation process and enhance the activity of the electrons,thus accelerating the degradation process.     

ADC14铝合金变速轮组合肋条早期断裂失效分析

采用化学成分分析、扫描电镜断口观察、金相检验等方法对某公司ADC14铝合金变速轮组合肋条的早期断裂原因进行了分析。结果表明，大量不均匀分布的粗大块状初晶硅、沿晶分布的块状脆性相、针状的脆性铁相以及较多的疏松铸造缺陷，严重割裂基体，使肋条的塑性降低、脆性增大，导致肋条产生早期脆性断裂。在此分析的基础上提出了铸造工艺的改进措施。     

铬天青S分光光度法测定水中铝含量

采用铬天青S作显色剂,抗坏血酸、盐酸羟胺作掩蔽剂,选用乙酸-乙酸钠缓溶液冲体系,用分光光度法比色测定水中铝含量. 结果表明，加入铬天青S溶液和溴化十六烷基吡啶溶液的量不同对吸光度有较大影响，显色时间在30～50min内吸光度值都较稳定；加入300～550mL缓冲溶液时，吸光度值变化平缓；对6份不同水样在不同时间重复测定,精密度和准确度良好,加标回收率为9825%~10350%.     

Effect of Si on austenite stabilization,martensite morphology,and magnetic properties in Fe-26%Ni-x%Si alloys

The effect of Si on the austenite stabilization, martensite morphology, and magnetic properties in Fe-26%Ni-x%Si (x=3.5, 5, and 6) alloys have been studied by means of transmission electron microscopy (TEM) and M?ssbauer spectroscopy techniques. TEM observations reveal that the martensite morphology is closely dependent on the Si content. The volume fraction changes of martensite and austenite phases, the hyperfine magnetic field, and isomer shift values have been determined by Mssbauer spectroscopy. The M?ssbauer study reveals that the hyperfine magnetic field, the isomer shift values and the volume fraction of martensite decrease with increasing Si content.