榆次西窑水源地三叠系刘家沟组裂隙水分析

根据西窑水源地的自然地理与地质构造，分析与论证了西窑水源地三叠系刘家沟组裂隙水的成因。并对刘家沟组裂隙水储量进行了预测。     

取料机导轮组长轴断裂原因分析及对策

针对取料机导轮组长轴断裂的原因，采取了相应的改进措施，避免了长轴的断裂，取得了良好的效果。     

断裂力学中应力强度因子的2种解法

提出Fourier积分变换和有限元数值解法求解工程断裂力学中应力强度因子KⅠ的2种解法，而KⅡ可通过两者之间的关系导出，其解值与实际均基本吻合；初步分析和验证了后者解析解的误差关系。这2种方法具有简单方便的特点。     

固溶处理对镍-铬-钼合金力学性能的影响及断口分析

采用金相显微镜、X射线衍射和扫描电镜等方法研究了热压成形镍-铬-钼合金固溶前后的金相组织、相的组成、断口形貌,以及固溶处理对合金力学性能的影响.研究结果表明:经1250 ℃/4 h固溶处理后的合金全为Ni的固溶体,而未经固溶处理和经1200 ℃/4 h固溶处理的合金除了含有Ni的固溶体外,还有单质Mo和一些金属间化合物;未经固溶处理的合金呈脆性断裂,拉伸强度要比固溶后合金的强度低,而固溶后合金呈延性断裂.经 1250℃/4 h和1200 ℃/4 h固溶处理后合金显示出以韧窝为主的断口形貌,与合金的延性断裂力学性能测试结果一致,而未经固溶处理的合金呈现以解理为主的断口形貌,与合金的脆性断裂力学性能测试结果一致.固溶处理前合金的硬度要比处理后的合金硬度高.     

A Theoretical Approach for Estimating Fracture Toughness of Ductile Metals

Fracture toughness is very important when applying Damage Tolerance Design and Assessment Techniques. The traditional testing approach for obtaining fracture toughness values is costly and time consuming. In order to estimate the fracture toughness of ductile metals, the fracture mechanics theory, materials plastic deformation theory and materials constructive relationships are employed here. A series of formulae and a theoretical approach are presented to calculate fracture toughness values of different materials in the plane stress and plane strain conditions. Compared with test results, evaluated values have a good agreement.     

激光重熔高速电弧喷涂FeNiCrAl涂层的组织与断裂韧性

采用激光技术对高速电弧喷涂FeNiCrAl涂层进行重熔处理.分析了重熔前后涂层的组织结构、物相成分、显微硬度与断裂韧性.结果表明:重熔后,喷涂层片层状堆叠结构与孔隙得到消除,组织结构变得均匀、致密,涂层与基体由机械结合变为冶金结合.喷涂层物相主要有α-Fe及金属间化合物AlFe₃,AlFe和Al_0.4Fe_0.6,重熔后,生成了新相Fe-Cr,［Fe, Ni］固溶体和碳化物NiC_○x.重熔后涂层的平均显微硬度为7.79GPa,约为基体硬度(2.5GPa)的3倍,约为喷涂层硬度(6.0GPa)的1.3倍.载荷为4.9,9.8N时,喷涂层的压痕尖头出现裂纹,涂层平均断裂韧性为1.20MPa·m^1/2,载荷为2.94~9.8N时,重熔后涂层的压痕尖头均没有观察到裂纹.     

含孔花岗岩破裂过程不同区域声发射特征

利用孔洞对声发射(AE)传播的阻隔作用,对AE探头监测区域进行分区.通过含孔花岗岩双轴加载破坏过程的AE多通道监测实验,研究了岩石变形破坏过程不同区域AE特征及其与破坏模式之间的关系.结果表明:试件的AE探头监测区域分为独测区、共测区、盲测区;试件共有两种破坏形式,“V”型和贯穿型;对于“V”型破坏的试件,主破裂发生在独测区,各通道的AE特征明显不同;对于贯穿型破坏试件,主破裂发生于共测区,各通道的AE特征较为相近.     

Joint Strength with Soldering of Al2O3 Ceramics After Ni-P Chemical Plating

Ni-P alloy was chemically plated on Al2O3 ceramics to produce uniform alloy coatings at temperatures below 70~C. Cu metal was electroplated onto the Ni-P coating to facilitate the soldering and shorten the chemical plating time. Then, the electroplated ceramic specimens were soldered with 60 wt.% Sn-40 wt.% Pb solder in active colophony. The highest shear strength was acquired after the heat treatment at 170℃ for 15 min. The joint fractures mostly propagated along the interface between the ceramics and the Ni-P coating, with some fracture in both the ceramics and the Ni-P coating near the interface and some along the interface between the Cu and Ni-P coatings. The results show that ceramic surface roughness and the chemical plating parameters influence the coating quality, and that suitable heat treatment before the soldering also improves the adhesion between the ceramics and Ni-P coatings, thus strengthening the joints.     

压剪复合应力强度因子和混凝土压剪断裂判据

含裂纹构件在压剪荷载作用下,裂纹面将闭合.本文在对裂纹前缘应力场的奇异性分析后,得出裂纹尖端只存在K_Ⅱ的结论.试验研究表明,混凝土在压剪情况下的破坏仍符合库仑-莫尔准则.因此,本文对压剪断裂提出了考虑裂纹面闭合和材料内摩擦双重影响的判据:在起裂时,是纯Ⅱ型扩展;其后是沿裂纹扩展方向剪断;并给出两个判据式.经8组单边裂纹压剪试样的试验验证,结果是令人满意的.     

用表面裂纹法研究表面强化层的疲劳裂纹扩展抗力

本文采用表面裂纹法研究了碳氮共渗、氮化及滚压强化层的疲劳裂纹扩展抗力。与常规的紧凑拉伸试验法相比，前者能灵敏地反映出表面强化层组织及性能的影响，后者却难于实现。试验证实碳氮共渗层中由于残留奥氏体应变诱发马氏体，导致疲劳裂纹扩展抗力提高；滚压强化及渗氮均能提高表面压应力，也使疲劳裂纹扩展抗力明显提高。