NaCl沉积和SO2污染对镁合金初期大气腐蚀行为的影响

借助扫描电镜(SEM/EDX)、X射线衍射(XRD)研究了NaCl单个因素对镁合金AZ91D初期腐蚀行为的影响,并对SO2和NaCl的协同作用进行了探讨.NaCl存在时初期破坏金属表面的保护膜,但后期微溶性腐蚀产物的生成导致腐蚀速率的降低.当NaCl和SO2同时存在时,反应生成的可溶性产物不具有阻碍的作用,同时他们会发生部分溶解生成自由移动的离子,大量难溶物在镁合金表面难以短时间形成,故NaCl和SO2同时存在引起的腐蚀远大于两者单独存在时引起的腐蚀加和.NaCl和SO2对镁合金的初期大气腐蚀具有明显的协同作用.     

原位颗粒含量对半固态7075铝合金组织的影响

制备具有不同原位TiC颗粒含量的喷射沉积7075铝合金,在610℃和620℃进行二次加热并保温30min,淬火固定半固态组织.采用扫描电镜观察其组织,利用平均截线法统计其晶粒尺寸,分析不同颗粒含量对喷射沉积7075铝合金半固态组织的影响规律.结果表明:当TiC颗粒含量达到2.91%(体积分数)时已经产生良好的钉扎效果,使得合金基本保持喷射沉积组织特征,能够满足后续的半固态成形工艺要求;TiC颗粒含量超过2.91%后,晶粒尺寸会进一步减小,但晶界上的颗粒明显增多并呈网状分布;TiC颗粒含量小于2.91%时,局部区域发生晶粒的异常长大现象,使合金组织的均匀化程度下降.     

AZ91D铸造镁合金交流脉冲双极微弧电沉积陶瓷膜

利用交流脉冲方法在AZ91D铸造镁合金表面成功实现阴、阳极微弧电沉积陶瓷膜,并使用SEM和xRD等手段对陶瓷膜的厚度、组织形貌、成分、结构和耐蚀性作了相应研究分析.结果表明,应用交流脉冲方法不仅能够在AZ91D铸造镁合金上实现阴、阳双极微弧电沉积陶瓷膜,同时在阴、阳极陶瓷膜中电沉积有稀土元素Ce.通过比较动电位扫描极化曲线和交流阻抗分析发现阴、阳极微弧氧化处理后AZ91D镁合金的耐蚀性得到显著提高.     

Atomic-scale computer simulation for early precipitation process of Ni75Al10V15 alloy

The kinetic model for a ternary system is introduced based on the microscopic diffusion form of the phase-field equations for a binary alloy. The equation is solved in the reciprocal space. This model is used to investigate the early precipitation process of Ni75-Al10V15 by simulating the atomic pictures of the two ordered phases and calculating the order parameters of γ′(Ni3Al) phase. Simulation results show that the γ′ ordered phases precipitate from the disordered matrix by a non-classical nucleation mechanism, and the nonstoichiometric γ′ ordered phase appears first and then transforms into the stoichiometric one. Clusters of V atoms appear at the γ′ phase boundaries followed by the formation of the nonstoichiometric θ ordered phase. The farther the location from γ′ phase boundary is, the lower the order degree of θ phase is. There exist two kinds of DO22 ordered domains: a horizontal one and a vertical one, related to their adjacent γ′ phase boundaries. The model could describe the atomic ordering and composition clustering simultaneously, and any a priori assumption about the new phase structure and precipitation mechanism etc. is unnecessary.     

Effect of heat treatment on magnetostriction and order-disorder transition of Fe83Ga17

Effect of heat treatment on magnetostrictive properties and order-disorder transition of 〈110〉-oriented polycrystal Fe83Ga17 alloys is investigated. It is found that magnetostriction and order degree of Fe83Ga17 alloys are very sensitive to cooling rate. Variation of magnetostriction is discussed in terms of order-disorder transition. Under compressive stress of 20 Mpa, saturation strain λs of partially ordered Fe83Ga17 alloys quenched into water reaches 298×10-6.     

退火工艺对轧制AZ31镁合金组织和性能的影响

对AZ31镁合金轧制板材在不同温度和时间进行了退火,研究了在退火过程中组织和性能的变化规律.实验结果表明,300℃轧制后的AZ31镁合金薄板材的组织中存在大量的孪晶.退火后,孪晶逐渐消失,形成等轴的再结晶晶粒.晶粒尺寸随退火温度的升高而变大,随退火时间的延长先细化后长大.同时,退火后板材的抗拉强度略有下降,但伸长率有明显提高,在200℃退火120 min后,伸长率可达到28%.     

冷却方式对Mg-3Nd合金显微组织和物相构成的影响

制备了急冷和铸造的Mg-3mass%Nd合金,采用显微组织分析、X-射线物相分析、电子探针微区成分分析、硬度和强度等检测分析,研究了合金的显微组织、物相构成和力学性能.探讨了压缩变形对铸态合金组织和性能的影响.结果表明,急冷可以大幅度减小晶粒尺度及改变合金的物相构成.急冷合金的物相构成为过饱和α-Mg固溶体相;铸态样品的物相构成为α-Mg固溶体和Mg41Nd5.实验还表明,铸态样品压缩变形后产生大量的形变孪晶,提高了合金的强度.     

微量镍元素添加对铁基非晶/纳米晶磁芯软磁性能的影响

用单辊法制备的宽20 mm,厚25μm的Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9和Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8合金带材,绕制成外径为40 mm,内径为25 mm的环型磁芯,然后将磁芯在不同的温度下进行退火处理,研究了微量Ni元素添加对合金带材的晶化行为以及对横向磁场退火后的非晶/纳米晶磁芯的软磁性能的影响。结果表明:与Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9合金带材相比,添加微量Ni元素的Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8合金带材的一级起始晶化温度Tx1和一级晶化峰温度Tp1降低,其二级起始晶化温度Tx2和二级晶化峰温度Tp2升高,两级起始晶化温度之间的差值ΔTx增大;与横向磁场退火后的Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9非晶/纳米晶磁芯相比,横向磁场退火后的Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8非晶/纳米晶磁芯的起始磁导率μi和饱和磁感应强度Bs减小,矫顽力Hc增大;当测试频率f和最大磁感应强度Bm不变时,有效幅值磁导率μa增大,比总损耗Ps和矫顽力Hc减小;当测试频率f不变时,电感Ls和品质因数Q增大;当励磁电流I不变时,感应电动势E大。     

石墨烯复合材料在警车防弹防护方面的研究

研究警车高性能防弹防护材料应用技术,尝试采用石墨烯改性的方式对陶瓷及铝合金的强度、韧性性能进行了改性提升,利用石墨烯改性材料制备了复合防弹板,并进行了实弹射击试验,研究了防弹警车应用可行性.试验结果表明,石墨烯改性可以有效提高陶瓷的断裂韧度,以及铝合金的强度及弹性模量.经53式7.62 mm穿甲弹三次射击,靶板无穿透,用石墨烯改性陶瓷制备的防弹装甲板,可有效降低材料密度,大幅度提高防弹性能,对车辆防弹性能及轻量化技术研究具有一定的参考价值.     

Improved dehydriding property of polyvinylpyrrolidone coated Mg-Ni hydrogen storage nano-composite prepared by hydriding combustion synthesis and wet mechanical milling

In this work, polyvinylpyrrolidone(PVP) coated Mg_(95)Ni_5 nano-composites were prepared by hydriding combustion synthesis(HCS) plus wet mechanical milling(WM) with tetrahydrofuran(THF) and donated as WM-x wt% PVP(x = 1, 3, 5 and 7) respectively. The phase compositions, microstructures and dehydriding property, as well as the co-effect of PVP and THF were investigated in detail. XRD results showed that the average crystal size of MgH_2 in the milled Mg_(95)Ni_5 decreased from 23 nm without PVP to 18 nm with 1 wt% PVP. The peak temperature of dehydrogenation of MgH_2 in the milled Mg_(95)Ni_5 decreased from 293.0 ℃ without THF to 250.4 ℃ with THF. The apparent activation energy for decomposition of MgH_2 in WM-7 wt% PVP was estimated to be 66.94 kJ/mol, which is 37.70 kJ/mol lower than that of milled Mg_(95)Ni_5 without THF and PVP. PVP and THF can facilitate the refinement of particle size during mechanical milling process. Attributed to small particle sizes and synergistic effect of PVP and THF, the composites exhibit markedly improved dehydriding properties.