基于二维正投影图三维重建的递归算法

模拟人脑读图中的形体分析法的叠加原理 ,给出三维重建的一种递归算法 .输入初始三视图 ,从中识别出一个简单子块 ,重建这个子块 ,设想从所求形体中切去该子块 ,即将重建过的视图立刻擦除 ,算出剩余形体的三视图 ,并作为新的初始三视图 ,再接受递归算法模块处理 ,如此循环 ,直到投影图信息量为零 .这种算法具有如下特点 :①将自顶向下法和自底向上法有机地结合 ;②在使用自底向上法时仅对三视图作局部计算 ;③使用过的视图信息及时消除 ,避免重复计算 ,效率高 ;④可以解决多解问题 .在使用优先原则时 ,可消去虚伪解 .     

Nanoindentation response analysis of TiN-Cu coating deposited by magnetron sputtering

To investigate the change of the mechanical properties of soft metals doped PVD(Physical Vapor Deposition)coatings after the migration of soft metal to the surface, TiN-Cu coating was deposited on Si(100) by magnetron sputtering. The microstructure and mechanical properties at room temperature and after vacuum heat treatment at 300 ℃ were investigated. The results showed that the grains were clustered and the microstructure was porous for TiN-Cu coating at room temperature, while many micro-and nano-sized Cu particles were observed on the surface after vacuum heat treatment at 300 ℃. The elastic properties of the TiN-Cu coating after vacuum heat treatment at 300℃ degraded compared with that at room temperature. The hardness and elasticity modulus of TiN-Cu coating kept constant(3.7 GPa and 125.0 GPa, respectively) with the increase of nano-indentation depth, while the hardness and elasticity modulus of TiN-Cu coating after vacuum heat treatment at 300 ℃ increased gradually.     

Effect of minor Sc on the microstructure and mechanical properties of AZ91 Magnesium Alloy

The as-cast and heat-treated microstructures and mechanical properties of the AZ91 magnesium alloys with and without minor Sc addition were investigated and compared in this paper. The results indicated that adding0.15–0.45 wt% Sc to the as-cast AZ91 alloy not only could modify and refine the Mg_(17)Al_(12) phase but also suppress the formation of the Mg_(17)Al_(12) phase. At the same time, the grains of the Sc-containing as-cast AZ91 alloys were also effectively refined. As a result, the mechanical properties at room temperature(RT) for the Sccontaining as-cast AZ91 alloys were effectively improved. In addition, adding 0.15–0.45 wt%Sc to the AZ91 alloy promoted the formation of the continuous precipitates(CP) during the aging treatment in spite of that the formation of the discontinuous precipitates(DP) was simultaneously suppressed. Accordingly, the Sc-containing as-aged AZ91 alloys obtained the relatively higher mechanical properties at RT than the as-aged AZ91 alloy.     

Effect of cold rolling process on microstructure and mechanical properties of high strength β titanium alloy thin sheets

The microstructure and mechanical properties of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe high strength titanium alloy sheets prepared by unidirectional cold rolling and two-step cross cold rolling were investigated. Results showed that the β phase grains were refined significantly by cold rolling followed by solution treatment for a short time.Compared to unidirectional cold rolling, the short time solution treatment after two-step cross rolling could significantly reduce the non-uniformity of the microstructure of the alloy sheets. After aging treatment at 550 ℃,the anisotropy of the mechanical properties still existed in the unidirectional rolled sheets, and the tensile strength was highest along the rolling direction. After solution and aging treatment, the anisotropy of the mechanical properties of the two-step cross rolling process sheet was not obvious than unidirectional cold rolling,and alloy had good strength and plasticity matching.     

Characteristic investigation of trilayered Cu/Al8011/Al1060 composite: Interface morphology,microstructure, and in-situ tensile deformation

In this work, Cu/Al8011/Al1060 trilayered composite with an ultrathin copper layer was fabricated successfully by the hybrid process of cast-rolling and hot-roll-bonding. The effects of heat treatment were investigated on the microstructure and mechanical behavior of the composite. The results showed that annealing temperatures above 300 ​°C led to the formation of new intermetallic compounds that joined their initial counterparts. Also, the interface growth was fast above 340 ​°C. It was found that the annealing temperature of 320 ​°C led to the optimal tensile properties of the composite. Through rolling, hard-brittle IMCs imposed intense plastic strains on the surrounding regions, resulting in further grain refinement of both metals in the vicinity of the interface. Although the kernel average misorientation of the trilayered composite was almost identical with the Cu/Al8011 bimetal, its amount was considerably decreased after heat treatment, as the distorted structure changed into a nearly strain-free one using the restoration phenomenon. The SEM-based in-situ tensile test showed that crack initiation occurred within the IMCs and propagated into the Cu strip, leading to its early fracture. However, the strength-displacement curve during in-situ tensile deformation did not decrease significantly due to the ultrathin copper layer.     

Enhanced performance of nano-sized SiC reinforced Al metal matrix nanocomposites synthesized through microwave sintering and hot extrusion techniques

In the present study, nano-sized SiC (0, 0.3, 0.5, 1.0 and 1.5 vol%) reinforced aluminum (Al) metal matrix composites were fabricated by microwave sintering and hot extrusion techniques. The structural (XRD, SEM), mechanical (nanoindentation, compression, tensile) and thermal properties (co-efficient of thermal expansion- CTE) of the developed Al-SiC nanocomposites were studied. The SEM/EDS mapping images show a homogeneous distribution of SiC nanoparticles into the Al matrix. A significant increase in the strength (compressive and tensile) of the Al-SiC nanocomposites with the addition of SiC content is observed. However, it is noticed that the ductility of Al-SiC nanocomposites decreases with increasing volume fraction of SiC. The thermal analysis indicates that CTE of Al-SiC nanocomposites decreases with the progressive addition of hard SiC nanoparticles. Overall, hot extruded Al 1.5 vol% SiC nanocomposites exhibited the best mechanical and thermal performance as compared to the other developed Al-SiC nanocomposites.     

Effect of Graphene Nanoplatelets addition on mechanical properties of pure aluminum using a semi-powder method

In recent years, graphene has attracted considerable research interest in all fields of science due to its unique properties. Its excellent mechanical properties lead it to be used in nano-composites for strength enhancement. This paper reports an Aluminum–Graphene Nanoplatelets(Al/GNPs)composite using a semi-powder method followed by hot extrusion. The effect of GNP nano-particle integration on tensile, compressive and hardness response of Al is investigated in this paper. It is demonstrated that 0.3 wt% Graphene Nanoplatelets distributed homogeneously in the matrix aluminum act as an effective reinforcing filler to prevent deformation. Compared to monolithic aluminum(in tension), Al–0.3 wt% GNPs composite exhibited higher 0.2% yield strength(+14.7%), ultimate tensile strength(+11.1%) and lower failure strain( -40.6%). Surprisingly, compared to monolithic Al(in compression), Al–0.3 wt% GNPs composite exhibited same 0.2% compressive yield strength and lower ultimate compression strength(- 7.8%),and lower failure strain(- 20.2%). The Al–0.3 wt% GNPs composite exhibited higher Vickers hardness compared to monolithic aluminum(+11.8%).Scanning electron microscopy(SEM), Energy-Dispersive X-ray Spectroscopy(EDS) and X-ray diffraction(XRD) were used to investigate the surface morphology, elemental percentage composition, and phase analysis, respectively.     

Enhanced mechanical properties of AZ31 magnesium alloy sheets by continuous bending process after V-bending

The effects of V-bending process, continuous bending process and combination process on the microstructure and mechanical properties and formability of an AZ31 magnesium alloy sheet were investigated. The experimental results showed that no twins were found in the microstructure of all samples after processes due to the fine grain. The V-bending and continuous bending processes were proved to be an effective approach to modify the mechanical properties and formability. While the samples after the combination process exhibited better mechanical properties and formability than the single processed sample. The yield strength significantly decreased with the value of 100 MPa and the fracture elongation enhanced to 18.3% at room temperature. The Erichsen value was 5.0 mm which was significantly increased by 117% compared with as-received sample. The superior formability of combination processed samples was mainly attributed to the smaller r-value and n-value.     

Microstructure and properties of in-situ synthesized Cu-1 wt%TiC alloy followed by ECAP and post-annealing

A dispersion-strengthened copper alloy with 1 wt% TiC for commercial electrical-contact wires was prepared by in-situ reaction casting, grain-ultrafining by equal-channel angular pressing (ECAP) and subsequent annealing with aim to obtain excellent comprehensive performance. The results showed that fine TiC particles were in-situ synthesized in the as-cast Cu matrix and aggregated in clusters, and thus mechanical properties of the as-cast alloy deemed insufficient. Continued ECAP at 473 K significantly refined the grains of the as-cast alloy and improved the distribution of TiC particles. Due to multiple strengthening mechanisms, the ECAP-processed alloys maintained good conductivity with obviously enhanced tensile strength and hardness values. After post-ECAP annealing, the elongation and conductivity of the fine-grained copper alloy increased with the adequate tensile strength. The novel combined process endows the alloy appropriate performance to serve current high-frequency electrification railway systems.     

浅谈《机械制图与AUTO CAD》精品课程的建设

我院一直致力于《机械制图与AUTO CAD》课程建设,本文结合该课程的发展历程,从课程体系、教学内容、教学方法、教学手段、教材建设及实践教学等方面,对精品课程建设的基本思路进行了阐述。