粉煤灰中主要有害元素的浸出与迁移实验研究

通过系统模拟实验研究了粉煤灰中主要有害元素在灰场正常运行条件下的浸出与迁移规律.结果表明,这种废水中的主要污染物是F和Cd,pH值严重超标.     

粉末送给率对激光熔覆层组织及性能的影响

在大量实验基础上，研究了激光熔覆过程对熔覆层组织和性能的影响。实验结果表明，随粉末送给率的增加，熔覆层厚度增加，熔覆层组织细化，熔覆层的硬度变化不大。     

粉末冶金Al-10%Ti复合材料的力学和耐磨性能

文章采用“冷压烧结+热挤压”的粉末冶金法制备出Al—10％Ti复合材料,研究了Al—10％Ti复合材料的孔隙率、抗拉强度、伸长率、硬度和耐磨行为。结果表明:与Al相比,Al-10％Ti复合材料的孔隙率较高,抗拉强度和伸长率较低,硬度和耐磨性较高;Al-10％Ti复合材料的磨损体积损失分别是Al的1/22.3及Qsn6.5-0.4的1/14.8,其磨损表面呈Al基体+Ti颗粒+孔隙的耐磨组织。     

化学镀法合成纳米Ag包覆Al_2O_3复合粉

以平均直径约为200nm的Al2O3粉为原料,以氨基溶液为镀液,硝酸银为初始材料,在反应过程中,控制最佳的还原剂浓度、反应时间等参量,使Al2O3表面获得均匀的金属Ag涂层·以HRTEM,XRD,EDS等手段研究了化学镀银所获得的Ag Al2O3复合粉的结构·结果表明,所有的Ag Al2O3复合粉具有壳 核结构,壳层由纳米非晶银和纳米银晶体颗粒构成,尺度分别是5nm和10nm·     

液相还原法制备纳米铜粉

以CuCl2和KBH4为原料采用液相还原法制备了铜粉，经XRD检测确定了反应生成物确为纳米铜粉，且经TEM检测粒径为20—40nm．该方法具有工艺简单，效率高，成本低等优点．并讨论了配位剂、反应温度等对反应结果的影响．     

铁基粉末烧结热锻材料的组织和性能

对比研究了两种不同成分铁基粉末烧结材料和粉末烧结热锻材料的显微组织和机械性能。结果表明，粉末烧结热锻材料综合机械性能显著高于粉末烧结材料。粉末烧结热锻材料的显微组织近似致密组织，密度可达7.60—7.70g/cm^3；表观硬度增加约50%；摩擦学特性显著提高。     

基于银薄膜/荷叶SERS效应直接检测婴儿配方奶粉中三聚氰胺

以天然荷叶为衬底,结合真空磁控溅射法沉积银薄膜,制备出了一种高效的表面增强拉曼散射(SERS)活性基底.研究发现银/荷叶基底对婴儿配方奶粉中掺杂的三聚氰胺(MA)表现出良好的识别能力,而不需作额外的样品预处理.对掺杂不同浓度三聚氰胺的奶粉溶液进行定量分析,在5~50 mg/L质量浓度范围内获得了较好的线性关系(线性相关系数R20.99).根据3σ准则,检测极限估计为1 mg/L.此外,银/荷叶基底具有良好的均匀性和重复性(相对标准偏差为7.64%和10.54%).该方法对婴儿配方奶粉中三聚氰胺的检测具有简单快速、成本低且无损等优点.     

Studies on induction hardening of powder-metallurgy-processed Fe-Cr/Mo alloys

Induction hardening of dense Fe-Cr/Mo alloys processed via the powder-metallurgy route was studied. The Fe-3Cr-0.5Mo, Fe-1.5Cr-0.2Mo, and Fe-0.85Mo pre-alloyed powders were mixed with 0.4wt%, 0.6wt%, and 0.8wt% C and compacted at 500, 600, and 700 MPa, respectively. The compacts were sintered at 1473 K for 1 h and then cooled at 6 K/min. Ferrite with pearlite was mostly observed in the sintered alloys with 0.4wt% C, whereas a carbide network was also present in the alloys with 0.8wt% C. Graphite at prior particle boundaries led to deterioration of the mechanical properties of alloys with 0.8wt% C, whereas no significant induction hardening was achieved in alloys with 0.4wt% C. Among the investigated samples, alloys with 0.6wt% C exhibited the highest strength and ductility and were found to be suitable for induction hardening. The hardening was carried out at a frequency of 2.0 kHz for 2-3 s. A case depth of 2.5 mm was achieved while maintaining the bulk (interior) hardness of approximately HV 230. A martensitic structure was observed on the outer periphery of the samples. The hardness varied from HV 600 to HV 375 from the sample surface to the interior of the case hardened region. The best combination of properties and hardening depth was achieved in case of the Fe-1.5Cr-0.2Mo alloy with 0.6wt% C.     

人参皂苷粉、银杏叶提取物对鸡胚绒毛尿囊膜血管新生的作用

为探讨人参皂苷粉和银杏叶提取物对鸡胚绒毛尿囊膜血管新生的影响,取孵育9天的种蛋,通过暴露鸡胚绒毛尿囊膜来建立模型,28只存活的鸡胚随机分为4组,包含两组空白载体的对照,一组加人参皂苷粉水溶液,一组加含银杏叶提取物药膜,作用3天后,观察分析鸡胚绒毛尿囊膜上血管生长的变化.结果显示:人参皂苷粉组,血管数量明显增多,但血管直径变细,颜色变淡;银杏叶提取物组,血管数量显著增多,血管颜色加深.研究发现:人参皂苷粉既能促进血管生成,又能抑制血管生成,总体表现为抑制;银杏叶提取物能够明显的促进血管的新生.     

Microstructure and properties of in-situ synthesized Cu-1 wt%TiC alloy followed by ECAP and post-annealing

A dispersion-strengthened copper alloy with 1 wt% TiC for commercial electrical-contact wires was prepared by in-situ reaction casting, grain-ultrafining by equal-channel angular pressing (ECAP) and subsequent annealing with aim to obtain excellent comprehensive performance. The results showed that fine TiC particles were in-situ synthesized in the as-cast Cu matrix and aggregated in clusters, and thus mechanical properties of the as-cast alloy deemed insufficient. Continued ECAP at 473 K significantly refined the grains of the as-cast alloy and improved the distribution of TiC particles. Due to multiple strengthening mechanisms, the ECAP-processed alloys maintained good conductivity with obviously enhanced tensile strength and hardness values. After post-ECAP annealing, the elongation and conductivity of the fine-grained copper alloy increased with the adequate tensile strength. The novel combined process endows the alloy appropriate performance to serve current high-frequency electrification railway systems.