NiTi形状记忆合金振动感知与主动控振研究

分析了复合于基体材料或嵌入机械结构中的ＮｉＴｉ丝对动、静应变的感知性能，基于ＮｉＴｉ形状记忆合金的振动感知和驱动特性，实现了机械系统振动的智能化控制，建立起机械系统的动力学模型。基于机械系统参数时变的特点，应用时频分析方法很好地描述了机械系统非平稳振动响应的过程，结果表明，ＮｉＴｉ形状记忆合金可灵敏地感知动、静应变，并可迅速作出反应，有效控制振动。     

Mg-1.3Mn-xCe-xZn镁合金显微组织和力学性能的研究

以Mg-1.3Mn合金为基合金,添加质量分数为1.0%或者2.0%的Ce以及质量分数为2.0%~6.0%的Zn,进行多元合金化,研究Ce,Zn对Mg-1.3Mn合金显微组织和力学性能的影响.实验结果表明：在Mg-1.3Mn合金中,一定量Ce,Zn的加入不但能明显地细化晶粒,而且能提高实验合金的抗拉强度和硬度.Mg-1.3Mn-1.0Ce-xZn合金的室温拉伸断裂机理随着Zn含量的增加也将发生改变.     

Effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of B–Y modified silicide coating

B–Y modified silicide coatings were prepared on Nb–Si based alloy by pack cementation at 1300 ℃ for 10 h. The effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of the coatings was investigated. The results show that the four coatings have similar structures, which possess a(Nb,X)Si_2 outer layer and a(Nb,X)_5Si_3 transitional layer. Y_2O_3 content in the pack mixtures has an obvious effect on the Si content in the coating. The mass gains of the coatings prepared with 0.5, 1, 2 and 3 wt% Y_2O_3 in pack mixtures are 2.33, 1.96, 2.05 and 2.86 mg/cm~2 after oxidation at 1250 ℃ for 100 h, respectively. The coating prepared with 1 wt% Y_2O_3 exhibits the best oxidation resistance due to the formation of a dense glass-like borosilicate scale.     

Atomic-scale segregation behavior of Sn/Ti and O at Σ3[11¯0](111) grain boundary in niobium

First-principle calculation was performed to illustrate the atomic arrangement and segregation behavior of Sn/Ti and O in View the MathML source grain boundary, and the interaction of oxygen interstitials with Sn/Ti atoms on the grain boundary was studied. The analyses on the segregation energies and geometric positions, and the electron densities show that Sn, Ti and O atoms segregate at the Σ3 grain boundary. And the preferred segregation sites of the impurities at View the MathML source were determined. When Sn segregates at grain boundary plane, the O atom prefers to the bulk-like site and shows no segregation tendency at grain boundary, whereas the segregated Ti atom can slightly enhance oxygen segregation at the grain boundary.     

热处理对镍基合金涂层与基体结合界面的影响

通过热浸镀法在普碳钢表面成功制备镍基合金涂层.为了提高镍基合金涂层与钢基体之间的结合强度,对镀有镍基合金涂层的基体进行了热处理.研究了热处理前、后结合界面处的显微组织和力学性能.结果表明,与热处理前相比,热处理后界面附近的涂层中析出物长大,界面处存在不连续块状铁的硼化物,界面两侧镍、铁互扩散距离增加,靠近界面的过渡带由5～8μm变为20μm.热处理前、后涂层均由γ-(Fe,Ni)、CrB、Cr2B和Cr3C2等相组成,过渡带相组成为γ-(Fe,Ni)、微量CrB和Fe23(C,B)6.热处理后,显微硬度由界面向涂层内逐渐增加,界面结合强度由140MPa提高到200MPa.     

Studies on induction hardening of powder-metallurgy-processed Fe-Cr/Mo alloys

Induction hardening of dense Fe-Cr/Mo alloys processed via the powder-metallurgy route was studied. The Fe-3Cr-0.5Mo, Fe-1.5Cr-0.2Mo, and Fe-0.85Mo pre-alloyed powders were mixed with 0.4wt%, 0.6wt%, and 0.8wt% C and compacted at 500, 600, and 700 MPa, respectively. The compacts were sintered at 1473 K for 1 h and then cooled at 6 K/min. Ferrite with pearlite was mostly observed in the sintered alloys with 0.4wt% C, whereas a carbide network was also present in the alloys with 0.8wt% C. Graphite at prior particle boundaries led to deterioration of the mechanical properties of alloys with 0.8wt% C, whereas no significant induction hardening was achieved in alloys with 0.4wt% C. Among the investigated samples, alloys with 0.6wt% C exhibited the highest strength and ductility and were found to be suitable for induction hardening. The hardening was carried out at a frequency of 2.0 kHz for 2-3 s. A case depth of 2.5 mm was achieved while maintaining the bulk (interior) hardness of approximately HV 230. A martensitic structure was observed on the outer periphery of the samples. The hardness varied from HV 600 to HV 375 from the sample surface to the interior of the case hardened region. The best combination of properties and hardening depth was achieved in case of the Fe-1.5Cr-0.2Mo alloy with 0.6wt% C.     

Regulating microstructures and mechanical properties of Al-Fe-Ni alloys

Mechanical properties of Al-Fe-Ni eutectic alloys have been investigated based on the nominal mass fraction of eutectic phase,and the added Fe/Ni mass ratio.The X-Ray diffraction,scanning electron microscopy equipped with energy dispersive spectroscopy and transmission electron microscope have been used to identify phase composition,characterize microstructure and crystal structure of Al_9FeNi phase,respectively.The results demonstrate that the nominal mass fraction of eutectic phase control the presence of primary phase.The tensile strength slightly increases,and the ductility deteriorates sharply as the volume fraction of primary phase increases.The Fe/Ni mass ratio has the profound effect on the microstructures(i.e.,size and shape) of primary phase.When the Fe/Ni ratio is approaching to 1,the primary phase becomes rod-like shape,which can enhance the ductility of alloys over the flake-like phase.The increasing cooling rate can effectively reduce the eutectic grains size and primary phase fraction,and further significantly improve mechanical properties of the alloys.     

智能材料与土木工程结构振动控制

结合国内外最新研究成果,综述了压电材料?电/磁流变液?形状记忆合金等智能材料的基本性能?工作原理及其在土木工程结构振动控制中的应用研究概况,并对研究及应用中存在的问题作了探讨.     

不同锤锻方式下Ti--6 Al--4 V合金组织及取向演变

利用扫描电镜和背散射衍射技术研究了Ti-6Al-4V合金在不同锤锻变形方式下的组织与取向变化。结果显示：随着镦拔变形次数的增加,Ti-6Al-4V合金中α相及β相组织均趋于均匀,而且两相的取向聚集越不明显;进一步热处理后,锻造过程中形变储存能得到释放,在释放过程中两相也会发生一定的倾转,轴向三次镦拔或者换向三次镦拔对组织均匀性改善明显。综合分析发现,密排六方结构的α相的取向分布对变形方式较敏感：原始棒材以及一次镦拔时,合金中α相的取向{0001}基面织构占了很大部分;随着镦拔次数增多,形变能增加,虽然{0001}基面滑移被抑制,但是{1010}、{1120}等柱面滑移以及{0111}、{1123}等锥面滑移得以开动,大幅地增加了取向的种类,进而降低了取向的集中性,使得取向更趋均匀化。     

NiAl基复合材料的研究进展

为了提高NiAl合金强度，改善NiAl合金塑性，在制备NiAl复合材料时，用不同的制备方法在NiAl合金中加入增强剂，如陶瓷或金属颗粒、晶须、短纤维和长纤维等制成复合材料，以不同的增强剂为基础总结了NiAl基复合材料研究在制备、结构、性能及机理等方面的最新进展。