香菇菌汤煮制工艺优化及其非挥发性特征风味物质研究

通过单因素实验和正交试验以感官评定及固形物溶出率为评价指标对香菇菌汤煮制工艺进行优化,并采用高效液相色谱技术对煮制后香菇及汤液中非挥发性特征风味物质进行测定。结果表明,当煮制温度为120℃、煮制时间为45min、香菇质量浓度为0.050g/mL时,香菇菌汤感官评价及固形物溶出率较好。在煮制过程中,香菇中风味物质逐渐向汤液中转移,使得汤液中可溶性糖醇、有机酸、呈味核苷酸等非挥发性风味物质含量显著高于煮制后香菇中含量。除此之外,在煮制后汤液中,特征性风味氨基酸含量也显著高于煮制后香菇中含量。但是,与新鲜香菇相比风味氨基酸在煮制后汤液及香菇中绝大多数含量有所降低。     

Microstructure and mechanical properties of SiC-particle-strengthening tri-metal Al/Cu/Ni composite produced by accumulative roll bonding process

In this study, a multilayer Al/Ni/Cu composite reinforced with SiC particles was produced using an accumulative roll bonding (ARB) process with different cycles. The microstructure and mechanical properties of this composite were investigated using optical and scanning microscopy and hardness and tensile testing. The results show that by increasing the applied strain, the Al/Ni/Cu multilayer composite converted from layer features to near a particle-strengthening characteristic. After the fifth ARB cycle, a composite with a uniform distribution of reinforcements (Cu, Ni, and SiC) was fabricated. The tensile strength of the composite increased from the initial sandwich structure to the first ARB cycle and then decreased from the first to the third ARB cycle. Upon reaching five ARB cycles, the tensile strength of the composite increased again. The variation in the elongation of the composite exhibited a tendency similar to that of its tensile strength. It is observed that with increasing strain, the microhardness values of the Al, Cu, and Ni layers increased, and that the dominant fracture mechanisms of Al and Cu were dimple formation and ductile fracture. In contrast, brittle fracture in specific plains was the main characteristic of Ni fractures.     

高速水润滑止推轴承的滑移润滑性能研究

建立了多种具有不同滑移区域分布特征的推力瓦数学模型,在考虑流体边界滑移效应、扩展了经典Reynolds方程并设定合理边界条件的基础上,借助MATLAB软件对模型进行数值仿真求解,研究了滑移区域分布方式、面积占比及滑移长度对轴承动压润滑性能的影响。结果表明,在靠近流场入口处沿周向分布滑移区域能显著提升不同转速条件下的推力瓦面承载力;当滑移区域面积占瓦面面积比介于0.3~0.4且滑移长度为1000nm时,轴承推力瓦面具有最优动压润滑性能。     

Microstructure and corrosion behavior of Al<Subscript>3</Subscript>Ti/ADC12 composite modified with Sr

In this study, we investigated the effect of the addition of Sr (0wt%, 0.1wt%, 0.2wt%, and 0.3wt%) on the microstructure and corrosion behavior of Al₃Ti/ADC12 composite by optical microscopy, X-ray diffraction, scanning electron microscopy, and energy diffraction spectroscopy. The results reveal that the α-Al phases were nearly spherical and 40 μm in size and that the eutectic Si phases became round in the composite when the Sr content reached 0.2wt%. The Al₃Ti particles were distributed uniformly at the grain boundary. The results of the corrosion examination reveal that the Al₃Ti/ADC12 composite exhibited a minimum corrosion rate of 0.081 g·m–2·h–1 for an Sr content of 0.2wt%, which is two thirds of that of unmodified composite (0.134 g·m–2·h–1). This improved corrosion resistance was due to galvanic corrosion, which resulted from the low area ratio of the cathode to anode regions. This caused a low-density corrosion current in the composite, thereby yielding optimum corrosion resistance.     

基于灰色模糊评价法的高校智库影响力评价研究

高校智库发展缺乏动力,成果难以转化,影响力有限。如何了解高校智库的影响力,采用何种方法来评价其影响力,对高校智库自身的发展和社会的进步都有一定的现实意义。本文从四个维度构建了高校智库影响力评价指标体系,并运用灰色模糊分析法对高校智库的影响力因素进行评价。通过对高校智库的影响力进行评价,有利于改善高校智库发展不充分、不平衡的问题,也有利于社会甄别高校智库的差异性。     

微量镍元素添加对铁基非晶/纳米晶磁芯软磁性能的影响

用单辊法制备的宽20 mm,厚25μm的Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9和Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8合金带材,绕制成外径为40 mm,内径为25 mm的环型磁芯,然后将磁芯在不同的温度下进行退火处理,研究了微量Ni元素添加对合金带材的晶化行为以及对横向磁场退火后的非晶/纳米晶磁芯的软磁性能的影响。结果表明:与Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9合金带材相比,添加微量Ni元素的Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8合金带材的一级起始晶化温度Tx1和一级晶化峰温度Tp1降低,其二级起始晶化温度Tx2和二级晶化峰温度Tp2升高,两级起始晶化温度之间的差值ΔTx增大;与横向磁场退火后的Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9非晶/纳米晶磁芯相比,横向磁场退火后的Fe_(73.5)Ni_(0.3)Cu_1Nb_3Si_(14.2)B_8非晶/纳米晶磁芯的起始磁导率μi和饱和磁感应强度Bs减小,矫顽力Hc增大;当测试频率f和最大磁感应强度Bm不变时,有效幅值磁导率μa增大,比总损耗Ps和矫顽力Hc减小;当测试频率f不变时,电感Ls和品质因数Q增大;当励磁电流I不变时,感应电动势E大。     

基于主动转矩分配的电动车车道保持辅助控制方法

 针对高速工况下四轮独立驱/制动电动车的车道偏离问题,提出一种基于主动转矩分配的车道保持辅助控制方法。该方法的辅助控制系统分为3层,顶层控制器根据人-车-路信息实时进行辅助控制决策,并计算车道保持所需的横摆响应;中层控制器基于滑模控制算法,计算横摆响应跟踪所需的附加横摆力矩;底层控制器通过主动转矩分配产生附加横摆力矩,干预车辆行驶轨迹,以达到车道保持的目的。采用CarSim/Simulink联合仿真进行高速单移线实验验证,结果表明,提出的基于主动转矩分配的四轮独立驱/制动电动车车道保持辅助控制方法,具有良好的车辆动力学稳定性,在高附路面和低附路面上均能够有效地干预车辆行驶轨迹,防止车辆偏离车道。     

图像美学质量评价技术发展趋势

 图像质量评价是利用计算机模拟人类视觉系统自动评价图像的失真程度,而图像美学质量评价是利用计算机模拟人类对美的感知与认知,自动评价图像的"美感",分析图像在构图、颜色、光影、景深、虚实等美学因素影响下所形成的美感刺激,这是计算美学与计算机视觉、心理学、虚拟现实等领域的学科交叉新方向,其在摄影摄像、电影电视、电子商务、服装设计、平面设计、文稿设计、工业设计、汽车行业、建筑行业、美容美妆等多个行业具有良好的应用前景。本文回顾了图像美学质量评价的发展历史,从基于人工设计美学特征的方法、基于美学特征深度学习的方法、图像美学质量评价的新任务、图像美学质量评价数据集构建等方面综述了该领域关键技术的发展情况,并展望了图像美学质量评价及其关键技术的发展趋势。     

VR/AR在文化旅游与影视中的应用创新 与趋势

 虚拟现实/增强现实（VR/AR）技术是一种改变大众生活方式的新兴科学技术,对大众文化领域将能够产生重大影响。本文分析VR/AR在文化旅游与影视领域的支撑技术及其演进、融合中的应用创新,研究其发展及对传媒文化产业的影响,探讨未来该领域的发展趋势。     

渝西北土壤重金属分布特征及其风险评价

为全面了解重庆西北地区（潼南区、铜梁区、合川区和大足区）土壤中重金属质量分数、分布特征及其生态风险,在该区共采集表层土壤样品6 792件,测定了As,Cd,Cr,Cu,Hg,Ni,Pb和Zn等8种重金属元素质量分数,并用土壤环境质量标准（GB15618-1995）和潜在生态风险指数对土壤重金属污染进行评价.结果表明：1）表层土壤Cd质量分数累积效应最大,是背景值的2.43倍,超标比例为18.67%,其余7种重金属元素质量分数平均值低于土壤环境质量一级标准值;2）空间分布特征表明,Zn,Cd,Pb,As,Ni,Cu和Cr 7种元素在研究区西部质量分数较高,Hg在东部质量分数较高,主要受地层控制和土地利用方式的影响;3）研究区重金属污染对该区构成的潜在生态危害由强至弱依次为：Cd,Hg,As,Pb,Cu,Ni,Cr,Zn,整体处于中等潜在生态风险等级,主要受Cd和Hg元素的影响,二者可能造成的生态危害应引起重视.