Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于一维数据逐段均匀条件下的参考分布研究

聚类分析中一个重要的问题是估计聚类数,GS方法通过参考分布对聚类数进行合理的估计,解决了其他聚类方法无法对应分为一类的数据进行分类的问题,具有更好的分类效果;目前已通过理论证明得出,在分布为对数凹且一维情况下,GS方法的参考分布为均匀分布,而有关其在其他条件下的参考分布研究较少;针对这一情况,提出解决一维且逐段均匀条件下GS方法的参考分布问题,以类内平方和为评价标准,通过拉格朗日乘数法求解与问题等价的优化问题,理论证出条件下总体均匀分布是类内平方和最大的情况,进而得出对于一维数据,逐段均匀条件下的参考分布仍为均匀分布的结论。     

项目引入法——可普遍采用的研究性学习模式

研究性学习是实施素质教育和创新教育的一种新型教学方式。在工科类课程的教学中 可采用引入一个工程项目,通过项目设计来学习研究新知识,完成教学计划。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

IMPLICITIZATION OF PARTIAL DIFFERENTIAL RATIONAL PARAMETRIC EQUATIONS

In this paper, we propose algorithms for the following problems in the implicitization of a set of partial differential rational parametric equations P. （1）To find a characteristic set for the implicit prime ideal of P; （2） To find a canonical representation for the image of P; （3）To decide whether the parameters of P are independent, and if not, to re-parameterize P so that the new parametric equations have independent parameters; （4） To compute the inversion maps of P, and as a consequence, to decide whether P is proper.     

Supercritical Fluid Carbon Dioxide in the Extraction of Lanolin and Its Alcohol

The use of supercritical fluid carbon dioxide (SF-CO_2) in extraction of lanolin and its alcohol issuperior to the conventional solvent extractionmethod. Its distinctive advantages include highextractive ratio, nontoxic and nonflammablesolvents, and minimal by-product pollution. The     

PXI在测控系统中的应用

随着有关PXI总线的规范和产品的推出，由于优良的性能指标和适宜的价格，使其受到各相关行业的广泛关注。对风洞测控系统的结构和系统配置作了具体的阐述，并对PXI总线在具体使用中的效果和特点作了较详细的介绍。