Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

疏松砂岩油藏大孔道定性识别新方法研究

疏松砂岩油藏在长期注水开发过程中,往往伴随着大孔道的出现,这严重影响了油藏水驱开发效果,制约了采出程度的进一步提高,因此,大孔道识别及有效封堵成为该类油藏急需解决的关键问题.通过研究分析,确定了影响大孔道从形成到发展的7种主要静态因素,以及标志大孔道形成的6种主要动态因素.将层次分析法及灰色关联法相结合,分别计算静态及动态因素的权重,建立了全新的大孔道定性识别模型.示踪剂监测结果验证了该方法的实用性和有效性.     

砂岩在西湖凹陷花港组交互式盖层中的作用初探

西湖凹陷花港组盖层具有砂泥岩交互式发育特征，而与泥岩伴生的砂岩类盖层的油气封闭作用研究较少。采用岩芯、镜下观察及压汞等分析方法，对砂泥岩交互式盖层中的砂岩特征进行了分析。结果表明，盖层中的砂岩可作为有效盖层，砂岩类盖层早期受沉积环境控制，含有较多的泥质而导致早期压实作用较强，加之晚期的黏土矿物转换及胶结物的发育，具备形成良好盖层的条件。在不同地区进行砂岩盖层有效性研究时应以沉积环境为基础，针对不同类型的砂岩进行成岩作用研究，并针对不同类型的砂岩样品进行实验分析以明确砂岩盖层的有效性。     

Geochemistry of Clayey Aquitard Pore Water as Archive of Paleo-Environment,Western Bohai Bay

The record of paleo-environment in clayey aquitard pore water is much more effective relative to aquifer groundwater owing to the low permeability of clayey aquitard. Oxygen-18 (18O), deuterium (D), an...     

火焰原子吸收分光光度法测定地表水中铜含量的不确定度评定

根据GB 7475—87《水质铜、锌、铅、镉的测定火焰原子吸收分光光度法》建立地表水样测定的数学模型,并根据JJF 1059.1—2012《测量不确定度评定与表示》的要求,计算测量过程中的不确定度分量,最终得出扩展不确定度.经检测计算,该地表水样品中的铜含量为1.53 mg/L,其扩展不确定度为0.036 mg/L,包含因子k=2,地表水样品中铜含量的测量结果应报告为(1.53±0.036) mg/L, k=2.结果表明,火焰原子吸收分光光度法测定地表水样中铜含量的不确定度主要来源于标准曲线拟合、标准溶液配制和样品重复测量.     

温度和机械载荷联合作用下油田超深井中硬质涂层膨胀锥与套管的屈服挤毁压强及试验验证

在充分考虑温度载荷、机械载荷、硬质涂层膨胀锥硬度、套管硬度对膨胀锥与套管之间屈服挤毁压强影响的基础上,根据分形理论和接触力学推导出膨胀锥与套管之间屈服挤毁压强的计算公式.数值分析表明:膨胀锥与套管之间的屈服挤毁压强随最终温度、分形粗糙度、线膨胀系数、硬质涂层膨胀锥布氏硬度、中间主应力系数、套管壁厚的增大而增大;当分形维数从1增大时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而减小;当分形维数增大到接近于2时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而增大;随拉压强度比的增大,膨胀锥与套管之间的屈服挤毁压强减小.屈服挤毁压强的计算值与试验测试值之间的相对误差为-8.9253%～-0.9901%.     

三维打印器件后处理液研究

分析了不同的填充强化剂(后处理A液)、不同的后处理B液基料、后处理B液中水性环氧乳液的掺量及后处理液浸泡时间对石膏基打印器件耐水性、抗压强度、尺寸偏差、表面微观结构的影响.结果表明:经纳米硅超硬固化剂处理后的打印器件抗压强度大幅提高,纳米硅超硬固化剂最适宜作为后处理A液;水性聚氨酯乳液PU-202B最适宜作为后处理B液的基料;后处理B液中加入水性环氧乳液,处理后打印器件的抗压强度增加、吸水率降低,但水性环氧乳液含量增加到一定程度后会出现尺寸偏差;后处理A、B液最佳浸泡时间分别为130 s和35 s;先浸泡后处理A液、后浸泡后处理B液的打印器件具有抗压强度高、吸水率小、表面较光滑、不脱粉等优良性能.     

超临界水氧化处理有机物废料的新技术

和传统方法相比，超临界水氧化处理有机物废料有着极大的优势。介绍了处理废料的原理和工业应用的可能性。     

Pilot Study on Nanofiltration Combined with Ozonation and GAC for Advanced Drinking Water Treatment

IntroductionThe conventional process for surface water treatment,which consists of flocculation, sedimentation and filtrationcurrently, had been applied inproducingdrinkingwater formany years. Although this process can remove turbidityand bacteria in surface water effectively, only about from20% to 30% of natural organic matter ( NOM) can beeliminated. When the purified water is disinfected bychlorination, these NOMs may react with chlorine. As aresult some dis…     

山西省吕梁区灌溉用水定额的编制

文章以调查典型县现状年灌溉用水定额为基础 ,以当地灌溉水可利用量为控制条件 ,采用逐级平衡的办法 ,制定吕梁区主要作物的灌溉用水定额