PLGA组织工程支架的构建及降解行为研究

用本体开环聚合方式合成不同摩尔比的PLGA（n(dl-LA)n(GA)分别为85／15，75／25，65／35，55／45)共聚物。^H NMR和溶解试验结果表明，共聚物各链段呈无规分布，GA序列长度在1.3-1.8之间。通过溶液浇铸造-低热模压-粒子沥滤技术构建了高度多孔的PLGA组织工程支架，考察了它们在Na2HPO4-NaH2PO4缓冲溶液中的降解行为。结果表明：随着水解的进行，PLGA的特性粘度及构建的多孔支架的压缩强度迅速下降，共聚物中GA组分含量赵大，下降的速度越快，与之对应的多孔支架的多孔结构形态保持时间也随共聚物中GA组合分含量增加而下降，分别为8周（n(dl-LA)/n(GA)分别为85/15和75/25）、4周（n(dl-LA)/n(GA)为65/35）和2周（n(dl-LA)/n(GA)为55/45）；但质量损失速率比[η下降速度慢得多，多孔支架的降解速率慢于薄膜的降解速率。     

软土地基深基坑土钉支护技术应用研究

以盐城市中医院病房楼深基坑支护设计和施工为例，就深基坑设计和施工中应该注意的问题，以及土钉墙支护技术在软土地基域的应用作一些研究，为软土地基深基坑工程的设计和施工提供借鉴。     

YBa2Cu3Oy体系中MgO纳米颗粒对磁通钉扎的影响

众所周知,氧化物超导体在高温高场下J_c值偏低及显著的磁通运动效应,阻碍了它的各种应用.因此,引进新的钉扎中心,如各种点缺陷(阴阳离子空位、部分元素替代和扩展型缺陷(如离子辐照产生的柱状缺陷)等,提高其J_c,研究相关的钉扎机制,具有理论和实际的双重意义.另外,实验发现,织构化的Y系样品在很大的温度和磁场范围内具有较高的临界电流,显然与样品内具有微米或亚微米尺寸的211脱溶物直接或间接引起的磁通钉扎有关.这说明大尺度的非超导粒子对磁通钉扎也有显著的强化效应.我们在YBa_2Cu_3O_y.体系中引入尺寸约为200nm的MgO纳米颗粒添加物,研究它对临界     

F—P腔双锁模激光器的理论分析

发展了双锁模激光器的动力学方程并求得其解析解。讨论了这类激光器的运转特性，所得结论与实验结果基本一致。     

抗拔非柱面改型钉的滚压加工及模具的设计计算

为了合理设计抗拔非柱面改型钉的滚压模具及加工设备，从改型钉的结构分析入手，研究分析了改型钉的成型原理和变形过程。在生产实践的基础上，提出了两种常用改型钉的参数及其滚压加工的工艺原理。     

被动锁模光纤环形孤子激光器的理论研究

分析了三阶色散和五阶饱和吸收等高阶非线性效应对被动锁模光纤环形孤子激光器的稳定性的影响，通过路径平均非线性薛定谔方程的求解，获得了被动锁模光纤环形孤子激光器稳定运行的条件     

关于非Hamilton图的一点注记

设Ｇ是一个ｋ－连通非Ｈａｍｉｌｔｏｎ图．Ｃ是最长圈，Ｈ是Ｇ＼Ｃ的分支。记ｙｉ∈ＮＣ＋（Ｈ），１≤ｉ≤ｋ。有．由它可推出一组大次和充分条件。     

壳聚糖/聚乙交酯三维编织物的力学性能

选择合适的生物材料和适宜的制备方法是实现组织修复、重建的重要环节．采用三维四步圆型编织方法,由壳聚糖和聚乙交酯(PGA)纤维制备绳索状三维编织物,研究其拉伸力学特性．研究结果表明：壳聚糖三维编织物的拉伸曲线与天然肌腱相似；直径为3．5mm的壳聚糖三维编织物在湿态下的最大拉伸载荷为50～85N,远低于其干态下值(140～225N),添加轴向纱对其无显著影响；在编织纱中掺入PGA纤维,可显著提高三维编织物的最大拉伸裁荷；PGA含量较高的壳聚糖/PGA三维编织物预期可以用作人工肌腱材料．     

Modeling Locking Angle of the Multi-layered Biaxial Weft Knitted Fabric in Shear Deformation

This paper introduces the construction of the multi-layered biaxial weft knitted fabric （MBWK fabric） and studies the locking angle of this kind of fabric. Moreover, a locking angle model of the MBWK fabric is established for the first time according to its unique construction. Two kinds of locking angles are considered under different restraint conditions： the locking angle θ1 controlled by the inserting yarns and the locking angle θ2 controlled by the stitch yarns. It is concluded that the ultimate value of the locking angle θ is the larger one of the two angles.     

Research on Flax Fiber Reinforced Polylactide Environmental Friendly Composite

Biodegradable polylactide acid （PLA） resin can be combined with flax fibers to produce biodegradable composite materials. In our study, commercial PLA fibers were mixed with flax fibers by a non-woven method so as to make non- woven pre-forms, which can be generated into flax fiber reinforced PLA environmental friendly composites by heat pressing technology. The tensile, flexural and impact properties are tested in order to evaluate the basic physical properties of the composites, and the influenced factors listed as making technology of the pre-forms, weight ratio of flax fibers and heat pressing technology are discussed and optimized, which can be described as weight ratio of flax fibers and PLA fibers is 50/50, heating temperature, time and pressure are respectively 195℃, 20 rain and 12.5 Mpa. Preliminary results show that mechanical properties of the flax/PLA composites are quite promising compared with flax/PP composites in coclrnon commercial automotive use. Scanning electron microscope （SEM） is used to analyze the tensile specimen fracture surfaces, which shows voids and gaps occurring between flax fibers and PLA matrix and sign of fiber pull.out, the strength of flax/PLA interface can be further improved.