Thermal conductivity measurement of InGaAs/InGaAsP superlattice thin films

The thermal conductivities of InGaAs/ InGaAsP superlattices with different period lengths were measured from 100 to 320 K using 3ω method. In this temperature range, the thermal conductivities were found to decrease with an increase in temperature. For the period length-dependant thermal conductivity, the minimum value does exist at a certain period length, which demonstrates that at a short period length, superlattice thermal conductivity increases with a decrease in the period length. When the period is longer than a certain period length, the interface thermal resistance dominates in phonon transport. The experimental and theoretical results confirmed the previous predictions from the lattice dynamics analysis, i.e. with the increase in period length, the dominant mechanisms of phonon transport in superlattices will shift from wave mode to particle mode. This is crucial for the cutoff of the phonons and lays a sound foundation for the design of superlattice structures.     

Effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties,microstructure,and texture of the alloy.The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture.After the pre-aging treatment and natural aging treatment(T4 P treatment),in contrast to the sheet with a uniform particle size distribution,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio(r) and strain hardening exponent(n).After solution treatment,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution.Additionally,they possess almost identical weak recrystallization textures,and their textures are dominated by CubeND {001}310 and P {011}122 orientations.     

Multi-threshold second-order phase transition in laser

We present a theory of the multi-threshold second-order phase transition,and experimentally demonstrate the multi-threshold secondorder phase transition phenomenon.With carefully selected parameters,in an external cavity diode laser system,we observe secondorder phase transition with multiple(three or four) thresholds in the measured power-current-temperature three dimensional phase diagram.Such controlled death and revival of second-order phase transition sheds new insight into the nature of ubiquitous secondorder phase transition.Our theory and experiment show that the single threshold second-order phase transition is only a special case of the more general multi-threshold second-order phase transition,which is an even richer phenomenon.     

消除7A05铝合金板材各向异性的热处理工艺

为提高7A05铝合金热轧板材的综合力学性能并减少各向异性,对7A05铝合金固溶、预时效、时效和形变处理等工艺对性能的影响进行了系统的研究. 比较了供货态、形变态、回归(RRA)态和采用预时效形变热处理的优化态热处理工艺对综合力学性能的影响. 结果表明:固溶的最佳温度为480 ℃,单级时效最佳工艺为120 ℃,24 h,双级时效中第一级时效最佳工艺为90 ℃,8 h,最佳形变为25%. 通过金相组织和力学性能测试结果表明:由于预时效析出促进形变热处理时亚晶等轴化,优化态强度高,进一步改善了合金性能,减少了轧制板材纵横向力学性能各向异性倾向.     

石墨基体等离子喷涂TiC涂层耐烧蚀性能研究

采用等离子喷涂方法在石墨基体上制备出较为致密的Mo黏结层和TiC耐烧蚀涂层,利用SEM,XRD表征氧乙炔烧蚀试验前后涂层的表面形貌与相结构.结果表明:随着烧蚀距离减小,涂层质量烧蚀率呈现先增加后减小的趋势,最终趋于稳定;随着烧蚀时间增大,致密化区域快速增大,涂层质量烧蚀率略有增加.烧蚀过程中涂层经历了点状熔融、线形连接、网状连接和完全致密4个过程.TiC涂层在高温燃流作用下氧化生成TiO2并熔融,在燃流冲刷和表面张力作用下发生黏性流动,形成TiO2致密层,从而减小了机械剥落,降低了涂层质量烧蚀率.     

一种包边模边界缩进控制方法

 将确定性优化方法用于板料包边设计.汽车板料包边仿真中变形区域小导致有限元模型在变形区域的网格很小,模型计算时间太长.本文针对影响板料包边后边界缩进较大的3个参数,建立目标函数的径向基函数近似模型,并用确定性优化方法对近似模型进行优化,近似模型计算效率高,提高了优化方法计算效率,使板料包边的优化设计成为可能,并为生产中的汽车板料控制包边后的边界缩进提供了一种新的思路.     

浅谈无线网络技术在智能交通系统中的应用

无线网络是一种融合短程无线通讯技术、逐渐被用于智能交通系统等需要数据采集与检测的相关领域.可为智能交通系统的信息采集提供一种有效手段,可监测路口各个方向上的车辆,根据监测结果,改进简化、改进信号控制算法,提高交通效率.     

新一代热轧TRIP钢的研究

对热轧后等温淬火的热轧Si-Mn TRIP钢进行了研究,通过对该钢的组织性能检测,讨论了其相变诱发塑性(TRIP)机制.结果表明:热轧Si-Mn TRIP钢中发生了残余奥氏体的应变诱导马氏体相变,表现出抗拉强度和总延伸率的良好配合.残余奥氏体的稳定性随等温保温时间的增加而增加,进一步增加等温时间则又使残余奥氏体稳定性降低.等温25 min时力学性能最佳,抗拉强度、总延伸率和强韧性平衡分别达到了774 MPa,33%和25 542 MPa%的最高值.     

对乙烯基苯磺酸钠接枝聚丙烯纤维

利用超声波的分散原理,以二甲苯作为界面剂,把引发剂过氧化苯甲酰(BPO)分散到聚丙烯(PP)纤维表层里,然后在水溶液中接枝对乙烯基苯磺酸钠(VSB),得到接枝产物PP-g-VSB纤维．研究反应条件对接枝率的影响,以及接枝率对接枝纤维性能的影响,并用热重分析加以表征．结果表明,反应温度为90℃、VSB和 BPO质量分数分别为8％,4％,可得到接枝率34％、离子交换当量1．2 mmol·g-1的强酸型离子交换纤维．     

玉米秸秆纤维复合缓冲包装材料的研究

研究了以聚醚多元醇、聚异氰酸酯为基体,以玉米秸秆纤维为增强体的新型复合缓冲包装材料,通过控制玉米秸秆纤维的添加量、发泡剂用量、交联剂与催化剂用量、反应温度等工艺参数,实验制备了具有可降解性能的缓冲包装材料,并利用静态压缩实验方法对比了该材料与发泡聚苯乙烯的缓冲性能.