面向产品投产比例的多Hoist调度研究

在电镀生产线上,多种不同类型的工件往往按照一定的比例关系组织生产,以应对多样化的订单需求,缩短订单交付周期,而为了克服由运输设备造成的生产瓶颈,加工设备之间的工件转运作业多采用数个自动化的Hoist(行车)来完成。针对面向产品投产比例的多Hoist调度问题,采用启发式策略实现多个不同类型工件在并行工作站上的分配,同时考虑工件加工时间窗口约束、工作站的使用能力约束以及Hoist无碰撞约束,构建了解决此类问题的混合整数规划模型。最后,以某印刷电路板制造企业的全板电镀生产实例验证了所建数学模型的实际应用价值。     

Corrosion behavior of high-strength spring steel for high-speed railway

The corrosion resistance and evolution of corrosion products in medium-carbon high-strength spring steels were investigated in a neutral salt spray (5wt% NaCl solution). A formation model of γ-FeOOH and a transformation model describing the conversion of γ-FeOOH to α-FeOOH were constructed. The results indicated that, at the initial corrosion stage, the corrosion resistance was gradually improved with the addition of Cr; however, with the addition of alloying element V, the corrosion resistance decreased. These results were attributed mainly to the initial corrosion stage being closely related to the matrix microstructure parameters such as grain-boundary character and dislocation density. After the rust layer was formed at a later corrosion stage, the corrosion resistance was reinforced with the addition of Cr and V because Cr strongly influenced the composition, structure, and morphology of the corrosion products. The results presented herein show that Cr was conducive to the transformation of γ-FeOOH into α-FeOOH. Moreover, V and Cr exhibited obvious synergy and were enriched in the inner layer of the corrosion products.     

具有隐性感染的登革热模型稳定性分析

建立了一类具有隐性感染和垂直传播的登革热模型.首先通过构造Lyapunov函数得到了无病平衡点E_0是全局渐近稳定的;进一步利用第二加性复合矩阵等理论得到了地方性平衡点E*是全局渐近稳定的条件.     

Effect of minor Sc on the microstructure and mechanical properties of AZ91 Magnesium Alloy

The as-cast and heat-treated microstructures and mechanical properties of the AZ91 magnesium alloys with and without minor Sc addition were investigated and compared in this paper. The results indicated that adding0.15–0.45 wt% Sc to the as-cast AZ91 alloy not only could modify and refine the Mg_(17)Al_(12) phase but also suppress the formation of the Mg_(17)Al_(12) phase. At the same time, the grains of the Sc-containing as-cast AZ91 alloys were also effectively refined. As a result, the mechanical properties at room temperature(RT) for the Sccontaining as-cast AZ91 alloys were effectively improved. In addition, adding 0.15–0.45 wt%Sc to the AZ91 alloy promoted the formation of the continuous precipitates(CP) during the aging treatment in spite of that the formation of the discontinuous precipitates(DP) was simultaneously suppressed. Accordingly, the Sc-containing as-aged AZ91 alloys obtained the relatively higher mechanical properties at RT than the as-aged AZ91 alloy.     

Influence of minor boron on the microstructures of a second generation Nibased single crystal superalloy

Boron is added into single crystal superalloys as a micro-alloying element to strengthen low angle grain boundaries.However,systematic investigations on the effect of boron on microstructures of single crystal superalloys are limitedly reported.The effect of boron on as-cast and heat-treated microstructures was investigated in two experimental Ni-based single crystal superalloys containing 3 wt% Re.The current results indicated that the volume fraction of(γ+γ′)eutectic and M_3B_2 borides was evidently increased,while the number of micropores was evidently decreased with the addition of 0.02 wt% boron.The(γ+γ′)eutectic could not be dissolved completely due to the lower incipient melting temperature caused by the formation of M_3B_2 borides.Meanwhile,the M_3B_2 borides were found to be enriched with indispensable strengthening elements Cr,Mo,W and Re,and this may lower the strengthening effect and cause stress concentration during high temperature creep.     

Mechanical characterization and strain-rate sensitivity measurement of Ti- 7333 alloy based on nanoindentation and crystal plasticity modeling

The relationship between crystal orientations and meso-mechanical properties of β phase Ti-7333 titanium was investigated through the combination of nanoindentation experiments and simulation. The crystal plasticity finite element(CPFE) model for nanoindentation of single body-centered cubic crystal was established based on the experimental data. And the crystal plasticity constitutive law was implemented to simulate the nanoindentation process, obtaining satisfied results with an acceptable error. From the simulated pileup morphology patterns with different crystal orientations, it was found that the β phase experienced a symmetrical and orientation-related deformation process. Meanwhile, the strain-rate sensitivity(SRS) of β phase was investigated through nanoindentation tests based on continuous stiffness measurement(CSM) under different strain rates,varying between 0.2, 0.05 and 0.01 s~(-1). Two grains with different orientations exhibited similar SRS exponents,m, calculated from the experimental results.     

WO3 nanoflakes decorated with CuO clusters for enhanced photoelectrochemical water splitting

The low quantum efficiency arising from poor charges transfer and insufficient light absorption is one of the critical challenges toward achieving highly efficient water splitting in photoelectrochemical cells. Three dimensions(3D) structures and heterojunctions have received intensive research interests recent years due to their excellent ability to separate photo-generated charges as well as the enhanced light harvesting property. Herein,3 D Cu O/WO_3 structure was fabricated through a facile solvothermal method followed by chemical bath deposition. The loading of Cu O clusters on WO_3 nanoflake arrays results in a much improved photocurrent density compared with that of pristine WO_3 nanoflake arrays, which reaches 1.8 m A/cm2 at 1.23 V vs. the reversible hydrogen electrode. The electrochemical impedance spectroscopy measurement demonstrates that the improved performance of Cu O/WO_3 electrode is attributed to the accelerated charge transfer kinetics as a result of the desirable band alignment in Cu O/WO_3 heterojunction. This work demonstrates a facile strategy to construct superior WO_3 electrode, which will ultimately allow for efficient storage of solar energy into hydrogen.     

城市轨道交通网络化运营条件下车辆基地的资源共享研究

随着国内城市轨道交通建设的快速发展与网络化运营的需求,车辆基地的资源共享研究受到日益广泛的关注与重视.该文旨在从线网车辆运用及维修角度对整个线网车辆基地进行分析研究,探讨相关各专业各种资源的共享、合理取舍和确定各车辆基地的规模.     

System deployment optimization in architecture design

Optimization of architecture design has recently drawn research interest. System deployment optimization （SDO） refers to the process of optimizing systems that are being deployed to activi- ties. This paper first formulates a mathematical model to theorize and operationalize the SDO problem and then identifies optimal so- lutions to solve the SDO problem. In the solutions, the success rate of the combat task is maximized, whereas the execution time of the task and the cost of changes in the system structure are mini- mized. The presented optimized algorithm generates an optimal solution without the need to check the entire search space. A novel method is finally proposed based on the combination of heuristic method and genetic algorithm （HGA）, as well as the combination of heuristic method and particle swarm optimization （HPSO）. Experi- ment results show that the HPSO method generates solutions faster than particle swarm optimization （PSO） and genetic algo- rithm （GA） in terms of execution time and performs more efficiently than the heuristic method in terms of determining the best solution.     

昆明长水国际机场鸟击防治管理信息平台系统架构

本文从昆明长水国际机场鸟击防治工作现状出发,提出人工管理、纸质台账存在的问题,由此引出构建鸟击防治管理信息平台的必要性。在需求及技术框架层面上,对系统功能进行了简洁明了的说明。