Kinetic modeling of copper bioleaching from low-grade ore from the Shahrbabak Copper Complex

The copper recovery from low-grade copper sulfide ore was investigated using microbial leaching. Several parameters substantially affect the bioleaching of copper; among them, pulp density and nutrient media were selected for investigation. The optimum conditions for copper recovery were a pulp density of 5 g/mL, a mixed-mineral salt medium of Acidithiobacillus thiooxidans (70vol%) and Acidithiobacillus ferrooxidans (30vol%), and 10vol% of inoculum. Under these conditions, the maximum bioleaching capacity of the medium for copper recovery was determined to be approximately 99%. The effect of pulp density on the kinetics of the bioleaching process was surveyed using both da Silva's method and constrained multilinear regression analysis. The kinetics of copper dissolution followed the shrinking core model, and the process was diffusion controlled at a pulp density of 5 g/mL. Nevertheless, at higher pulp densities, the process was controlled by chemical reaction.     

Novel cytotoxic peptides from the tropical marine cyanobacterium Hormothamnion enteromorphoides. 1. Discovery, isolation and initial chemical and biological characterization of the hormothamnins from wild and cultured material

A Caribbean cyanobacterium, Hormothamnion enteromorphoides, was found to produce a complex mixture of ichthyotoxic peptides, perhaps explaining the apparent absence of predation upon these potentially palatable life forms. Bioassay-guided fractionation was used to isolate these toxic and antimicrobial natural products, and a variety of techniques including HR FAB mass spectrometry, 2D-NMR, traditional hydrolysis-amino acid analysis, and several chemical reactions were used to define the basic structural features of the major peptide, hormothamnin A. Hormothamnin A is a cyclic undecapeptide containing six common and five uncommon or new amino acid residues. HPLC analyses indicate that the relative proportions of these peptide natural products remain relatively constant between different collection locations and years, however, they do vary seasonally. Clonal isolates of this cyanobacterium in culture produce the full spectrum of toxic peptides.     

Influence of B source materials on the synthesis of TiB2-Al2O3 nanocomposite powders by mechanical alloying

An Al2O3-TiB2 nanocomposite was successfully synthesized by ball milling of Al, TiO2 and two B source materials of B2O3 （system （1）） and H3BO3 （system （2））. Phase identification of the milled samples was examined by Xray diffraction. The morphology and microstructure of the milled powders were monitored by scanning electron microscopy and transmission electron microscopy. It was found that the formation of this composite was completed after 15 and 30 h of milling time in systems （1） and （2）, respectively. More milling energy was required for the formation of this composite in system （2） due to the lubricant properties of HaBO3 and also its decomposition to HBO2 and B2O3 during milling. On the basis of X-ray diffraction patterns and thermodynamic calculations, this composite was formed by highly exothermic mechanically induced self-sustaining reactions （MSR） in both systems. The MSR mode took place around 9 h and 25 h of milling in systems （1） and （2）, respectively. At the end of milling （15 h for system （1） and 30 h for system （2）） the grain size of about 35-50 nm was obtained in both systems.     

Design and Manufacture of a Wax Injection Tool for Investment Casting Using Rapid Tooling

A rapid wax injection tool of a gearbox shift fork was designed, simulated, and manufactured using rapid prototyping and rapid tooling technology to save time and cost of producing wax models used for the investment casting process. CAE simulation softwares, in particular, MoldFlow, are used to get wax injection moulding parameters such as filling parameters, temperature profiles, freeze time, speed, and pressure. The results of this research were compared with conventional wax model production methods. The criteria of such comparison were based upon parameters such as time, cost, and other related characteristics, which resulted in saving of 50% in time and 60% in cost. In this research, design, assembly, and wax injection operation of the wax tool took 10 days. Considering the fact that wax melting temperature is as low as 70°C and injection pressure of 0.5 MPa, the tool suffers no damage due to the thermal and pressure stresses, leading to the mass production of wax models.