一种新型扭转金属阻尼器及其减震性能分析

为解决现有金属阻尼器应力分布不均匀的问题,设计了一种新型层间扭转型金属阻尼器,推导出初始刚度和屈服荷载表达式,并通过往复加载试验对其力学性能进行研究.根据阻尼器的试验过程建立有限元模型,分析其变形后的应力分布,对设有该扭转型耗能梁段与剪切型耗能梁段的Y形支撑结构进行了抗震性能研究.结果 表明:建立的扭转金属阻尼器力学模...     

基于LabVIEW的电梯钢丝绳状态监测多通道数据采集

针对电梯钢丝绳运行状态存在的在线监测困难、故障检测不准确的问题,搭建模拟电梯钢丝绳运行的实验台,通过设计励磁器、检测器结构,设计基于LabVIEW的电梯钢丝绳状态监测多通道数据采集系统。对钢丝绳断丝、磨损等常见故障信号进行多通道采集并实时显示波形图、存储数据以便进行进一步分析。试验表明,该系统可以多通道采集钢丝绳的漏磁信号,提高了信号的空间分辨率,能准确地检测不同程度的钢丝绳断丝磨损等故障信号,并将采集到的数据以TDMS文件的形式保存下来进行波形回放,进一步定量分析故障部位及程度。     

On-line spheroidization process of medium-carbon low-alloyed cold heading steel

Conventionally manufactured 35CrMo cold heading steel must undergo spheroidization annealing before the cold heading process. In this paper, different types of deformation processes with various controlled cooling periods were operated to achieve on-line spheroidal cementite using the Gleeble-3500 simulation technique. According to the measured dynamic ferrite transformation temperature (A_d3), the deformation could be divided into two types: low temperature deformation at 810 and 780℃; “deformation-induced ferrite transformation” (DIFT) deformation at 750 and 720℃. Compared with the low temperature deformation, the DIFT deformation followed by accelerated cooling to 680℃ is beneficial for the formation of spheroidal cementite. Samples subjected to both the low-temperature deformation and DIFT deformation can obtain granular bainite by accelerated cooling to 640℃; the latter may contribute to the formation of a fine dispersion of secondary constituents. Granular bainite can transform into globular pearlite rapidly during subcritical annealing, and the more the disperse phase, the more homogeneously distributed globular cementite can be obtained.     

Preparation of Functional Polymeric Microspheres

1 Introduction Because of the wide applications in the area of biomedical and biotechnological fields, a great efforts have been done to fabricate different kinds of microspheres with tailored structural and surface properties over the last decade~([1]). Among them, stimuli responsive microspheres are microspheres that show ability to change their physical-chemical properties and colloidal properties in response to environmental stimuli such as changes of temperature, pH, chemicals, light, ele…     

Synthesis of two new thiazolidines and their hepatoprotective effects

Two new 2-substituted thiazolidine-4（R）-carboxylic acids （TCAs）, 2-glusosaminal-TCA （GIcNH2Cys） and 2-N-acetyl-glueosanlinal-TCA （GlcNAeCys）, were synthesized. Their protective effects against liver toxicity induced by acetaminophen （APAP） were investigated in a mice model. The resuits demonstrate that administration of TCAs （ i. p. , 800 mg/kg） 30 min after APAP challenge efficiently decrease ALF, AST, and LDH levels in liver. GlcNAcCys shows the best proteetive eftects, decreasing ALT, AST and LDH levels to 63%, 18.4% and 37% of the APAP group respectively. Comparison with the control showed that APAP greatly decreases total sulfhydlyl （T-SH） levels （43%）, non-protein hound sulfhydryl （NP-SH） levels （50%） and total antioxidative capabilities （57%） in the liver 24 hr after challenge. TCAs treatments 30min after APAP challenge significantly elevate sulfhydryl levels and total antioxidative capabilities. APAP administration also markedly （P 〈 0.05） increases liver lipid peroxidation to 1.65 and 1.17 times that of the control 4 hr and 24 hr after APAP administration respectively. TCAs treatments can inhibit lipid peroxidation as measured by decreased malondialdehyde （MDA） contents in liver. The histopathological results also further confirm the hepatoprotective effects of TCAs. In conclusion, our data show that TCAs, GleNAcCys particularly, have hepatoprotective anti antioxidant etfects.     

基于Fluent的搅拌流场模拟研究

使用Fluent对某钢厂KR脱硫搅拌工艺过程进行数值模拟,研究桨叶长度、搅拌头插入深度及转速对搅拌效果的影响。结果表明,尺寸为2B=1 300mm的长浆叶搅拌头搅拌效果较好,搅拌头插入深度为液面下800mm左右较为适宜,搅拌头转速以80～120r/min为宜。     

提升机主轴疲劳强度的模糊可靠性设计

将模糊可靠性理论应用于提升机主轴的疲劳强度设计中,建立了提升机主轴疲劳强度的模糊可靠性设计数学模型,介绍了它的设计方法,并给出了算例。算例中通过分析比较,说明了模糊可靠性设计的合理性和先进性。     

无线传感器网络中间件技术

目前,面向应用的无线传感器网络普遍缺乏统一开放的软件体系架构和高效的开发接口,因而阻碍了其进一步发展和应用.针对无线传感器网络特点,全面介绍无线传感器网络中间件软件的概念、设计需求与关键技术,并在此基础上分析其体系结构.同时,提出无线多媒体传感器网络中间件的概念,并构建一种基于Agent的无线多媒体传感器网络中间件体系.     

Electrical conductivity changes of bulk tin and Sn-3.0Ag-0.5Cu in bulk and in joints during isothermal aging

The changes of electrical conductivity (resistance) between Sn-3.0Ag-0.5Cu solder joints and printed circuit board (PCB) assembly during aging at 125℃ were investigated by the four-point probe technique. The microstructural characterizations of interfacial layers between the solder matrix and the substrate were examined by optical microscopy and scanning electronic microscopy. Different types of specimens were designed to consider several factors. The experimental results indicate that electrical conductivities (resistances) and residual shear strengths of the solder joint specimens significantly decrease after 1000 h during isothermal aging. Microcracks generate in the solder matrix at the first 250 h. Besides, the evolutions of microstructural characterizations at the interface and the matrix of solder joints were noted in this research.     

纸浆纤维表面的木素磺酸盐层层自组装疏水改性

为实现纸浆纤维表面的疏水改性,利用木素磺酸盐(LS)与Cu2+层层自组装的方式对纸浆纤维进行了表面修饰.通过X射线光电子能谱分析、原子力显微镜分析以及动态接触角测量的方法对自组装后的纤维表面进行了分析和表征.结果表明:纤维表面S和Cu的含量随着LS与Cu2+的交替组装而增加,说明LS和Cu2+在纤维表面的层层自组装是可行的;随着层层自组装的进行,纤维表面的微细纤维逐渐被木素致密覆盖;表面木素的增加致使AFM相图的平均相位逐渐增大,使表面疏水性提高;纤维的初始接触角随着自组装层数的增加而增大,且一定时间(0.08 s)内接触角的下降速率减小;组装5层木素后,纤维表面的初始接触角由0°提高至104.8,°0.08 s后下降至78.9°,表面由高度亲水性变为具有一定疏水性.由此可得出结论:通过控制SL自组装的层数可以有效且可控地实现纸浆纤维的疏水改性.