论辛词中的“有我之境”

辛弃疾的词以强烈的感情色彩见长,辛词中的境界可以分为豪放洒脱和婉约清丽两种,这两种境界中都带有浓厚的主观色彩,皆可称为“有我之境”。     

A continuous-wave Raman silicon laser

Achieving optical gain and/or lasing in silicon has been one of the most challenging goals in silicon-based photonics because bulk silicon is an indirect bandgap semiconductor and therefore has a very low light emission efficiency. Recently, stimulated Raman scattering has been used to demonstrate light amplification and lasing in silicon. However, because of the nonlinear optical loss associated with two-photon absorption (TPA)-induced free carrier absorption (FCA), until now lasing has been limited to pulsed operation. Here we demonstrate a continuous-wave silicon Raman laser. Specifically, we show that TPA-induced FCA in silicon can be significantly reduced by introducing a reverse-biased p-i-n diode embedded in a silicon waveguide. The laser cavity is formed by coating the facets of the silicon waveguide with multilayer dielectric films. We have demonstrated stable single mode laser output with side-mode suppression of over 55 dB and linewidth of less than 80 MHz. The lasing threshold depends on the p-i-n reverse bias voltage and the laser wavelength can be tuned by adjusting the wavelength of the pump laser. The demonstration of a continuous-wave silicon laser represents a significant milestone for silicon-based optoelectronic devices.     

Cleaner and convenient preparation of 3-（4,6-dimethoxy-pyrimidin-2-yloxy）-2-methyl-phenol

Environmental concerns have highlighted the need of cleaner technologies. A cleaner, convenient and selective technology has been developed for the preparation of 3-(4,6-dimethoxy-pyrimidin-2-yloxy)-2-methyl-phenol (DPMP) from 2-methyl-benzene-1,3-diol in water as solvent. The isolated yield of DPMP is up to 86% in good selectivity. The product structure was characterized by conventional methods, 1^H-NMR and MS. This technology belongs to the modern concept of environmentally friendly low wastes or non-wastes technology (LWNWT).     

散装船装载计算机的研究

对散装船栽计算机的数学模型及软件的设计方面作了一定的探讨与研究，这对散装船装载计算机的研制与正确使用的有价值的。     

GFFD： Generalized free-form deformation with scalar fields

The novel free-form deformation (FFD) technique presented in the paper uses scalar fields definedby skeletons with arbitrary topology. The technique embeds objects into the scalar field by assigning a field value to each point of the objects. When the space of the skeleton is changed, the distribution of the scalar field changes accordingly, which implicitly defines a deformation of the space. The generality of skeletons assures that the technique can freely define deformable regions to produce a broader range of shape deformations.     

Transpositional behaviour of the Ds element in the Ac/Ds system in rice

Insertional mutagenesis based on maize Activator/Dissociator (Ac/Ds) transposons is becoming a ma- jor approach used to produce a saturated mutant collection in rice. In this research, Ds-T-DNA trans- formed homozygotes were crossed with Ac-T-DNA transformed homozygotes in order to establish an Ac/Ds transposon system in rice. The successive investigation of Ds transposition from F1 to F5 gen- erations indicated that the frequencies of germinal transposition increased over successive genera- tions and reached 54.2% in F3 generation. The Ds transposition pattern revealed that a Ds transposition induced an approximately 170-bp deletion of T-DNA sequence and another Ds transposition carried a 272-bp T-DNA sequence. Using thermal asymmetric interlaced PCR (TAIL-PCR), some flanking se- quences of the Ds element were amplified. Analyses of 17 Ds-flanking sequences showed that five Ds were inserted into gene regions. The Ds could transpose not only to the linked sites but also to the unlinked sites. The frequency of inter-chromosomal transposition of Ds was 33.3%.     

A comparison of iron phthalocyanine and cobalt porphyrin on the electrochemical catalysis in Ni-MH battery

The effects of iron phthalocyanine （FePc） and cobalt porphyrin （CoPp） on inner pressure and cycle behavior of sealed Ni-MH batteries were investigated in this study. The morphology of battery electrode was observed by SEM. The electrochemical impedance spectroscopy of floating-charge/discharge battery was also measured. Experimental results show that the addition of FePc or CoPp to the alloy electrode is an effective approach to decrease the internal pressure of battery during the process of charge and overcharge. In contrast to CoPp, the battery with FePc exhibits a slower capacity decay and a smaller overpotential at the same charge-discharge rate. As an electrocatalyst, FePc may more effectively speed up the reduction of oxygen, and decrease its reduction potential. As a result, the charge process is accelerated, the gas evolution is reduced and the pulverization of electrode materials is slowed down.     

Study on variation of smoke component concentration with water mist applying

Interaction between water mist and fire smoke is studied by experiments in an ISO 9705 room, The variation of 02, CO and CO2 concentration is disclosed, and the mathematical models of smoke component con- centration with water mist pressure and ventilation speed are established according to the experimental results. It is found in the experiment that the smoke component concentration will break when ventilation speed exceeds 1.5 kg/s. This paper provides necessary theory for water mist technology using in smoke restraining.     

Full-scale model tests and nonlinear analysis of prestressed concrete simply supported box girders

Full-scale model tests were carried out on a 30 m span prestressed concrete box girder and a 20 m span prestressed concrete hollow slab. Failure models were prestressed reinforcement tensile failure and crashing of roof concrete, respectively. The ductility indexes of the box girder and hollow slab were 1.99 and 1.23, respectively, according to the energy viewpoint. Based on the horizontal section hypothesis, the nonlinear computation procedure was established using the limited banding law, and it could carry out the entire performance analysis including the unloading, mainly focusing on the ways to achieve the unloading curves computation through stress-strain, moment-curvature and load-displacement curves. Through the procedure, parameters that influence on the bearing capacity, deformation performance and ductility of the structures were analyzed. Those parameters were quantity of prestressed reinforcement and tension coefficients of prestressed reinforcement. From the analysis, some useful conclusions can be obtained.