重金属镉对花背蟾蜍蝌蚪生长发育的影响

研究了镉质量浓度在0.0015,0.0300和0.1500mg/L时对花背蟾蜍(Bufo raddei)蝌蚪生长发育的影响。结果表明:不同质量浓度镉能缩短花背蟾蜍蝌蚪50％出膜时间,但对蝌蚪最终孵化率没有影响;镉能影响蝌蚪的生存率,对蝌蚪的生长发育具有明显的抑制作用(P<0.01),但组间差异均不显著(P>0.05);同时各质量浓度水平均导致蝌蚪头部泡状膨大、‘S’型尾和体形奇小(为正常体长的0.50～0.67)等,致畸率0.1500 mg/L质量浓度水平最高(2.25％),0.0300 mg/L水平次之(2.00％),0.0015 mg/L水平最低(0.50％)。     

水泥土环境中粉煤灰水化与活性激发研究

水泥—粉煤灰与土充分拌合条件下,经过初级和次级2个过程形成水泥土固结体。粉煤灰的活性效应较之形态效应和微集料效应对水泥土强度的贡献是显著和持久的。活性激发剂———粉状硅酸钠溶出的OH-对粉煤灰网络聚合度比较高的“硬壳层”有腐蚀作用,同时硅酸钠水解产生的SiO32-在水化环境中可阻止水化硅酸钙生成过多而沉积在粉煤灰表面。通过构建粉煤灰在水泥土环境中的水化模型及SEM、力学性质等测试手段,分析了粉煤灰的水化与固结特性。     

弹性地基连续板的三弯矩方程

借助单跨弹性地基板弯曲方程的标准解答组，方便地导出了两对边简支弹性地基连续板的三弯矩方程．推导过程中，根据两对边简支的边界条件，同时还利用板中间支座处的变形连续条件，将板的挠度沿ｙ方向展成正弦级数．因导得的连续板三弯矩方程给计算带来了很大方便，故在工程设计中有重要应用．另外，提出的推导方法不仅概念清晰，而且容易推广到解决正交异性连续板的三弯矩方程     

界面处理和冷却条件对玻璃纤维与聚丙烯界面结合的影响 I.不同界面处理对界面剪切强度的影响

通过测定,得出马来酸酐改性聚丙烯（ＭＰＰ）是提高玻璃纤维与聚丙烯树脂界面剪切强度的关键因素,而偶联剂的变化对体系界面剪切强度的影响较少,用仪器分析证实了酸酐基团与玻璃纤维表面发生化学反应的实质,以及当界面存在改性聚丙烯时,应选择Ａ－１７４ＴＭ硅烷偶联剂处理增强聚丙烯的玻璃纤维,而不是传统的Ａ－１１００ＴＭ硅烷偶联剂。     

ALE有限元法解二维自由面流体大晃动问题

从Navier-Stokes方程和连续性方程出发，在ALE描述下，用四边形单元对所求区域加以划分；并借助于Galerkin加权余量法导出相应的有限元方程组，在有限元计算中速度和压力均采用四节点线性插值函数；通过二维自由面流体大晃动问题实例的计算，给出相应的计算结果，阐明了该方法的优越性和局限性。     

A separate two-stage pulse tube cooler working at liquid helium temperature

A novel 4 K separate two-stage pulse tube cooler (PTC) was designed and tested. The cooler consists of two separate pulse tube coolers, in which the cold end of the first stage regenerator is thermally connected with the middle part of the second regenerator. Compared to the traditional coupled multi-stage pulse tube cooler, the mutual interference between stages can be significantly eliminated. The lowest refrigeration temperature obtained at the first stage pulse tube was 13.8 K. This is a new record for singlestage PTC. With two compressors and two rotary valves driving mode, the separate two-stage PTC obtained a refrigeration temperature of 2.5K at the second stage. Cooling capacities of 508mW at 4.2K and 15W at 37.5K were achieved simultaneously. A one-compressor and one-rotary valve driving mode has been proposed to further simplify the structure of separate type PTC.     

Selective Smoothed Finite Element Method

The paper examines three selective schemes for the smoothed finite element method (SFEM) which was formulated by incorporating a cell-wise strain smoothing operation into the standard compatible finite element method (FEM). These selective SFEM schemes were formulated based on three selective integration FEM schemes with similar properties found between the number of smoothing cells in the SFEM and the number of Gaussian integration points in the FEM. Both scheme 1 and scheme 2 are free of nearly incompressible locking, but scheme 2 is more general and gives better results than scheme 1. In addition, scheme 2 can be applied to anisotropic and nonlinear situations, while scheme 1 can only be applied to isotropic and linear situations. Scheme 3 is free of shear locking. This scheme can be applied to plate and shell problems. Results of the numerical study show that the selective SFEM schemes give more accurate results than the FEM schemes.     

用具有零权的平差方法求解秩亏自由网的研究

以秩亏自由网平差的法方程系数阵的特征根作为虚拟权 ,构造两组虚拟误差方程 ,其中一组具有零权 ,从而用具有零权的平差思想 ,导出求解秩亏自由网待估参数平差值及其协因数的公式 ,并指出 ,此结果与用主成分估计法求解秩亏自由网的结果完全一致。     

基于遗传算法的模糊聚类方法

针对模糊c 均值算法容易收敛于局部极小点的缺陷 ,将遗传算法应用于模糊c 均值算法的优化计算中 .算法采用实数编码 ,提高了试验精度 .实验证明基于遗传算法的模糊聚类方法能够在一定程度上克服初值的影响 ,跳出局部极小点 ,在大样本的聚类方面有较大的优势 .     

一个虚拟手原型的实现

以５ＤＴ 公司生产的数据手套作为手势输入设备,开发了一个虚拟手原型．它以手的运动学模型为基础,采用层次结构法构造手的几何模型,极大地方便了虚拟手的图形显示和实时更新的实现．根据人手的运动约束关系得到各关节弯曲角度的相对比例关系,就能从数据手套得到的７ 个传感数据获得整个手的运动情况,并用静态碰撞检测法处理虚拟手与其他物体的碰撞检测,在运行期间不断地对用户手势进行手势映射计算找到最匹配的手势,执行与该手势对应的动作．本原型简单易行,便于增加手势,最后给出了实现结果．