Corrosion behavior of high-strength spring steel for high-speed railway

The corrosion resistance and evolution of corrosion products in medium-carbon high-strength spring steels were investigated in a neutral salt spray (5wt% NaCl solution). A formation model of γ-FeOOH and a transformation model describing the conversion of γ-FeOOH to α-FeOOH were constructed. The results indicated that, at the initial corrosion stage, the corrosion resistance was gradually improved with the addition of Cr; however, with the addition of alloying element V, the corrosion resistance decreased. These results were attributed mainly to the initial corrosion stage being closely related to the matrix microstructure parameters such as grain-boundary character and dislocation density. After the rust layer was formed at a later corrosion stage, the corrosion resistance was reinforced with the addition of Cr and V because Cr strongly influenced the composition, structure, and morphology of the corrosion products. The results presented herein show that Cr was conducive to the transformation of γ-FeOOH into α-FeOOH. Moreover, V and Cr exhibited obvious synergy and were enriched in the inner layer of the corrosion products.     

Complementation in the composition of steel slag and red mud for preparation of novel ceramics

A method for preparing novel ceramics was developed in this study. Different ratios red muds were added to steel slags to optimize the preparation of novel ceramics by a traditional ceramic preparation process. The sintering mechanism, microstructure, and performance were studied by X-ray diffraction techniques, scanning electron microscopy, and combined experiments of linear shrinkage, water absorption, and flexural strength. The results confirmed that red mud can reduce the volumetric instabilities through the complementarity of red mud and ferroalloy slag. The crystal phases in the ceramics are all pyroxene group minerals, including diopside ferrian, augite, and diopside. The flexural strength of the ceramic that contains 40wt% red mud and was prepared at the optimal sintering temperature (1140℃) is greater than 93 MPa; its corresponding water absorption is less than 0.05%.     

Mineral-phase evolution and sintering behavior of MO-SiO2-Al2O3-B2O3 (M=Ca,Ba) glass-ceramics by low-temperature liquid-phase sintering

In this work, network former SiO₂ and network intermediate Al₂O₃ were introduced into typical low-melting binary compositions CaO·B₂O₃, CaO·2B₂O₃, and BaO·B₂O₃ via an aqueous solid-state suspension milling route. Accordingly, multiple-phase aluminosilicate glass-ceramics were directly obtained via liquid-phase sintering at temperatures below 950℃. On the basis of liquid-phase sintering theory, mineral-phase evolutions and glass-phase formations were systematically investigated in a wide MO-SiO₂-Al₂O₃-B₂O₃ (M=Ca, Ba) composition range. The results indicate that major mineral phases of the aluminosilicate glass-ceramics are Al₂₀B₄O₃₆, CaAl₂Si₂O₈, and BaAl₂Si₂O₈ and that the glass-ceramic materials are characterized by dense microstructures and excellent dielectric properties.     

鲢鱼鱼鳞蛋白提取工艺研究

以鲢鱼鱼鳞为研究对象,研究了提取温度,提取时间,料液比对鱼鳞蛋白质提取率的影响,并进一步通过正交实验对其提取工艺进行了优化。研究结果表明:鱼鳞蛋白质提取率随着提取温度、提取时间、料液比的增加而提高。其提取的最佳条件是:提取温度90℃,提取时间6 h,料液比1:25,在此条件下鲢鱼鱼鳞蛋白质的提取率为77.41%。     

截流钢筋石笼起动流速计算方法研究

以工程截流中的单体钢筋石笼作为研究对象,深入探讨了其起动机理.通过对单体钢筋石笼受力分析,推导出其起动流速计算公式,分析了公式中拖曳力系数C_D、上举力系数C_L的影响因素.通过水槽模型试验,研究了不同摩擦因数条件下多种尺寸的正六面体钢筋石笼、条形六面体钢筋石笼、扁形六面体钢筋石笼起动流速变化规律;定量地分析了C_D和C_L与钢筋石笼扁度系数λ以及沙粒雷诺数Re*的相关关系,绘制了(λ,Re*,C_D)与(λ,Re*,C_L)的分布云图.经验证表明,起动流速计算公式和C_D、C_L分布云图二者结合的钢筋石笼起动流速计算方法的计算值与试验值基本一致,较好地反映了钢筋石笼的起动情况.     

Effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties,microstructure,and texture of the alloy.The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture.After the pre-aging treatment and natural aging treatment(T4 P treatment),in contrast to the sheet with a uniform particle size distribution,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio(r) and strain hardening exponent(n).After solution treatment,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution.Additionally,they possess almost identical weak recrystallization textures,and their textures are dominated by CubeND {001}310 and P {011}122 orientations.     

高压天然气管道喷射火热辐射计算

天然气燃爆喷射火事故可能造成人员建筑严重损害,为研究大型天然气喷射火燃爆特性,使用CFD计算软件,对质量流量在5 kg/s以上,压力分别为12 MPa与6 MPa,泄漏孔径在25 mm、50 mm与100 mm时的高压天然气喷射火进行仿真,得到这六种工况下喷射火火焰尺寸、温度分布和近地热辐射强度分布曲线,并得到喷射火长度与宽度和泄漏孔直径的线性变化关系.与喷射火常用的Thornton模型对比,仿真结果计算的火焰长度基本符合,热辐射结果在泄漏中心30 m以外基本相近,两种方法都可用于估算远距离喷射火热辐射强度,为天然气设施安全设计提供参考.     

UHPLC-MS/MS法同时测定大鼠血浆中汉黄芩素、隐绿原酸和白杨素-7-O-葡萄糖醛酸苷含量

建立了UHPLC-MS/MS同时测定大鼠血浆中的汉黄芩素、隐绿原酸和白杨素-7-O-葡萄糖醛酸苷含量的方法。以芹菜苷为内标,采用ACQUITY UPLC HSS T3色谱柱(2.1 mm×100 mm, 1.8 μm),乙腈和0.1％甲酸溶液为流动相,流速为0.2 mL·min^-1。结果表明,汉黄芩素、隐绿原酸和白杨素-7-O-葡萄糖醛酸苷线性范围为1～1 000 ng·mL^-1(R2>0.99),最低定量浓度为1 ng·mL^-1,提取回收率、基质效应均符合生物样品分析要求。建立的方法灵敏、准确,可用于大鼠血浆中汉黄芩素、隐绿原酸和白杨素-7-O-葡萄糖醛酸苷的测定及其药代动力学研究。     

Effect of cold rolling process on microstructure and mechanical properties of high strength β titanium alloy thin sheets

The microstructure and mechanical properties of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe high strength titanium alloy sheets prepared by unidirectional cold rolling and two-step cross cold rolling were investigated. Results showed that the β phase grains were refined significantly by cold rolling followed by solution treatment for a short time.Compared to unidirectional cold rolling, the short time solution treatment after two-step cross rolling could significantly reduce the non-uniformity of the microstructure of the alloy sheets. After aging treatment at 550 ℃,the anisotropy of the mechanical properties still existed in the unidirectional rolled sheets, and the tensile strength was highest along the rolling direction. After solution and aging treatment, the anisotropy of the mechanical properties of the two-step cross rolling process sheet was not obvious than unidirectional cold rolling,and alloy had good strength and plasticity matching.     

The hidden disintegration of cluster heterogeneity in Fe-based glass-forming alloy melt

The evolution of liquid metal at high temperature is known much less than their solid states. This is partially due to that the message concerning clusters, metastable phase or heterogeneity in liquid is usually too slight to be traced. Here, we shed some light on the nature of structural evolution of Fe-based glass-forming alloy during overheating process by the investigation of high-temperature melt viscometry and first principles simulations. It was found that a structural transition around 1400 ℃ occurred in the melts of initial homogeneous ingot, heterogeneous ingot and amorphous ribbons jointly, and was confirmed by the results from differential scanning calorimeter(DSC), and ab initio molecular dynamics(AIMD). Combining these results with Fe-Si-B ternary phase diagram and the melting characteristics of Fe-B compounds, it is safe to conclude that the disintegration of Fe_2B type clusters to Fe_3B-type clusters leads to the observed transition. These results offer a significant reference for the preparation and property control of Fe-based amorphous alloys.