Extraction and separation of nickel and cobalt from saprolite laterite ore by microwave-assisted hydrothermal leaching and chemical deposition

Extraction and separation of nickel and cobalt from saprolite laterite ore were studied by using a method of microwave-assisted hydrothermal leaching and chemical deposition. The effects of leaching temperature and time on the extraction efficiencies of Ni2+ and Co2+ were investigated in detail under microwave conditions. It is shown that the extraction efficiencies of Ni2+ and Co2+ from the ore pre-roasted at 300℃ for 5 h were 89.19% and 61.89% when the leaching temperature and time were about 70℃ and 60 min, respectively. For the separation process of Ni and Co, the separation of main chemical components was performed by adjusting the pH values of sulfuric leaching solutions using a NaOH solution based on the different pH values of precipitation for metal hydroxides. The final separation efficiencies of Ni and Co were 77.29% and 65.87%, respectively. Furthermore, the separation efficiencies of Fe of 95.36% and Mg of 92.2% were also achieved at the same time.     

Design of a low-alloy high-strength and high-toughness martensitic steel

To develop a high strength low alloy (HSLA) steel with high strength and high toughness, a series of martensitic steels were studied through alloying with various elements and thermodynamic simulation. The microstructure and mechanical properties of the designed steel were investigated by optical microscopy, scanning electron microscopy, tensile testing and Charpy impact test. The results show that cementite exists between 500℃ and 700℃, M₇C₃ exits below 720℃, and they are much lower than the austenitizing temperature of the designed steel. Furthermore, the Ti(C,N) precipitate exists until 1280℃, which refines the microstructure and increases the strength and toughness. The optimal alloying components are 0.19% C, 1.19% Si, 2.83% Mn, 1.24% Ni, and 0.049% Ti; the tensile strength and the V notch impact toughness of the designed steel are more than 1500 MPa and 100 J, respectively.     

Photocatalytic activity of ferric oxide/titanium dioxide nanocomposite films on stainless steel fabricated by anodization and ion implantation

A simple surface treatment was used to develop photocatalytic activity for stainless steel. AISI 304 stainless steel specimens after anodization were implanted by Ti ions at an extracting voltage of 50 kV with an implantation dose of 3 × 1015 atoms·cm?2 and then annealed in air at 450℃ for 2 h. The morphology was observed by scanning electron microscopy. The microstructure was characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The photocatalytic degradation of methylene blue solution was carried out under ultraviolet light. The corrosion resistance of the stainless steel was evaluated in NaCl solution (3.5 wt%) by electrochemical polarization curves. It is found that the Ti ions depth profile resembles a Gaussian distribution in the implanted layer. The nanostructured Fe₂O₃/TiO₂ composite film exhibits a remarkable enhancement in photocatalytic activity referenced to the mechanically polished specimen and anodized specimen. Meanwhile, the annealed Ti-implanted specimen remains good corrosion resistance.     

Study on stable and meta-stable carbides in a high speed steel for rollers during tempering processes

A high speed steel (HSS) was studied for rollers in this work. The steel was quenched at 1150℃ and tempered at 520℃. The phase structures of the steel were determined by X-ray diffraction (XRD), and the hardness of specimens was measured. The volume fraction of carbides was counted by Image-Pro Plus software. The typical microstructures were observed by field emission scanning electron microscope (FESEM). Stable and meta-stable carbides were deduced by removing the existing phases one by one in the Fe-C equilibrium calculation. It is found that the precipitated carbides are bulk-like MC, long stripe-like M₂C, fishbone-like M₆C, and daisy-like M₇C₃ during the tempering process. The stable carbides are MC and M₆C, but the meta-stable ones are M₂C, M₇C₃, and M₃C.     

Effects of the flow rate of hydrogen on the growth of graphene

Graphene samples with different morphologies were fabricated on the inside of copper enclosures by low pressure chemical vapor deposition and tuning the flow rate of hydrogen. It is found that the flow rate of hydrogen greatly influences the growth of graphene. Thermodynamic analysis indicates that a higher flow rate of hydrogen is favorable to the formation of good quality graphene with regular morphology. However, the mass-transfer process of methane dominates the growth driving force. At very low pressure, mass-transfer proceeds by Knudsen diffusion, and the mass-transfer flux of methane decreases as the flow rate of hydrogen increases, leading to a decrease in the growth driving force. At a higher pressure, mass-transfer proceeds by Fick's diffusion, and the mass-transfer flux of methane is dominated by the gas velocity, whose variation determines the growth driving force variation of graphene.     

棉花根际微生物的初步觀察

1.棉花根际細菌总数,一方面是愈近根面愈多,愈远愈少;另一方面是随到棉花发育时期的不同作有規律的变化,出苗后渐增,至开花期达于最大,以后又慢慢减少,R/S最高可达127强。2.孢子細菌数相反,根面最少,距根面愈远愈多。3.氨化細菌数在棉花根际细菌总数中占絕对优势,往往达后者的80—90%,其数量上的变化也和后者完全一致。4.棉花根面沒有发現亚硝酸化細菌和硝酸化細菌。根际之中虽然有,但为量不多。5.棉花根部分泌有抑制纖維素分解細菌的物貭,因此棉花根面上沒有发現纖維素分解细菌,根际內也很少,并且在距根十厘米以內的土壤中;数量上的变化也不大。其量随植物的生长而增加,增加的趋势是开花期以前緩慢,結铃以前剧速上升。6.棉花根际沒有找到好气性自生固氮菌。因为原来土壤中就沒有它,或者极少。     

Using Greedy algorithm： DBSCAN revisited Ⅱ

The density-based clustering algorithm presented is different from the classical Density-Based Spatial Clustering of Applications with Noise (DBSCAN) (Ester et al., 1996), and has the following advantages: first, Greedy algorithm substitutes for R(*)-tree (Bechmann et al., 1990) in DBSCAN to index the clustering space so that the clustering time cost is decreased to great extent and I/O memory load is reduced as well; second, the merging condition to approach to arbitrary-shaped clusters is designed carefully so that a single threshold can distinguish correctly all clusters in a large spatial dataset though some density-skewed clusters live in it. Finally, authors investigate a robotic navigation and test two artificial datasets by the proposed algorithm to verify its effectiveness and efficiency.     

Diagnosis of glioma by multivoxel 1H-MRSI

Glioma is one of the most malignant tumors due to its special construction of the glia cells and its character of infiltration. The usual procedure of the treatment is the surgical resection followed by radiotherapy with or without chemotherapy. This combined treatment needs the precise information on the extent of the tumor's infiltration and tumor grading, and then the determination can be made as to when, where and what kind of treatment should be used. Functional imaging modalities display advantages in defining the heterogeneous characters and histological grade. This paper describes how the ratios of Cho/NAA and Lac/NAA measured by magnetic resonance spectroscopy imaging (MRSI) could be used to define the cancer cell distribution in tissues, tumor burden and malignancy, and the results are proved to be consistent with the histological observation.     

5-羟色胺在F344大鼠下丘脑释放及其免疫调节作用

在F344雄性大鼠腹腔注射血蓝蛋白(KLH),研究T 细胞依赖抗原初始免疫反应对中枢神经系统5 羟色胺(5 HT)代谢的影响。当免疫刺激大鼠4天后,其下丘脑匀浆5 羟色胺水平出现降低,同时应用在体脑微透析技术研究发现清醒大鼠腹腔注射血蓝蛋白4天后,其下丘脑前叶细胞外液的5 羟色胺水平增加。为了评价在免疫反应中大鼠下丘脑5 羟色胺释放效应,本文应用氯苯丙胺(PCA)选择性预先耗竭5 羟色胺释放,并测定这些动物在注射血蓝蛋白后抗体产生情况。结果显示在应用氯苯丙胺预处理的血蓝蛋白免疫动物特异抗体IgM和IgG与未用氯苯丙胺预处理的动物比较均有明显增加(P<0.01)。上述资料表明,对于T 细胞依赖抗原,其初始抗体产生的量是由位于下丘脑5 羟色胺神经终端抑制性递质释放所调节。