Liquid-phase aerobic oxidation of benzyl alcohol catalyzed by mechanochemically synthesized manganese oxide

Benzyl alcohol oxidation by molecular oxygen using solid manganese oxide as a catalyst and n-heptane as the solvent was studied in the liquid phase. The catalyst was synthesized by a simple mechanochemical process at room temperature and was characterized by different physical methods. The catalyst was highly active and 100% selective for benzyl alcohol conversion to benzaldehyde. The solid catalyst can be recovered from the reaction mixture by simple filtration and can be re-used. We found n-heptane to be an excellent solvent for the oxidation reaction, and that the catalyst did not leach into solution.     

Deposition behavior and tribological properties of diamond-like carbon coatings on stainless steels via chemical vapor deposition

A systematic investigation was carried out to observe the deposition rate of a diamond-like carbon (DLC) coating on two stainless steel substrates by chemical vapor deposition (CVD). The objective of this research is to study the deposition behavior of the DLC coating and its tribological properties in different combinations of methane (CH₄) and nitrogen, which were used as precursor gases. The results reveal that the deposition rate increases with increasing CH₄ content up to 50vol%. The hardness of the DLC-deposited layer also increases while the friction coefficient decreases with increasing CH₄ gas content up to 50% in the precursor gas mixture.     

CFH haplotypes without the Y402H coding variant show strong association with susceptibility to age-related macular degeneration

In developed countries, age-related macular degeneration is a common cause of blindness in the elderly. A common polymorphism, encoding the sequence variation Y402H in complement factor H (CFH), has been strongly associated with disease susceptibility. Here, we examined 84 polymorphisms in and around CFH in 726 affected individuals (including 544 unrelated individuals) and 268 unrelated controls. In this sample, 20 of these polymorphisms showed stronger association with disease susceptibility than the Y402H variant. Further, no single polymorphism could account for the contribution of the CFH locus to disease susceptibility. Instead, multiple polymorphisms defined a set of four common haplotypes (of which two were associated with disease susceptibility and two seemed to be protective) and multiple rare haplotypes (associated with increased susceptibility in aggregate). Our results suggest that there are multiple disease susceptibility alleles in the region and that noncoding CFH variants play a role in disease susceptibility.     

CuCrW(Al2O3) nanocomposite: mechanical alloying,microstructure, and tribological properties

The effect of alumina nanoparticle addition on the microstructure and tribological properties of a CuCrW alloy was investigated in this work.Mechanical alloying was carried out in a satellite ball mill.The tribological properties of the samples were evaluated using pin-on-disk wear tests with different pins (alumina,tungsten carbide,and steel pins).The results indicated that the tungsten carbide pin had a lower coefficient of friction than the alumina and steel pins because of its high hardness and low surface roughness.In addition,when the sliding rate was decreased,the weight-loss rate increased.The existence of alumina nanoparticles in the nanocomposite led to a lower weight-loss rate and to a change in the wear mechanism from adhesive to abrasive.     

Effect of Y2O3 on the crystallization kinetics of TiO2 nucleated LAS glass for the production of nanocrystalline transparent glass ceramics

Crystallization kinetics of metastable β-quartz solid solution as a desirable phase for the production of transparent lithium aluminosilicate (LAS) glass ceramics was investigated in the presence of Y₂O₃. Accordingly, differential thermal analysis scans were performed thoroughly to study the mechanism of crystallization kinetics. The aim of this investigation is to discover the complicated mechanism of crystallization process in the presence of co-additives and accordingly find a way for increasing the transparency of glass ceramics. It is shown that the bulk (3D) growth is intensively increased by the enhancement of Y₂O₃. Then again, reducing nucleation and increasing growth mechanisms were recognized for the LAS system in the presence of Y₂O₃. Results of the investigation illustrate that when co-additives are added to glasses, it is necessary to nucleate the optical component separately before the growth process.     

Effect of microstructure on the breakage of tin bronze machining chips during pulverization via jet milling

In this study, jet milling was used to recycle tin bronze machining chips into powder. The main purpose of this study was to assess the effect of the microstructure of tin bronze machining chips on their breakage behavior. An experimental target jet mill was used to pulverize machining chips of three different tin bronze alloys containing 7wt%, 10wt%, and 12wt% of tin. Optical and electron microscopy, as well as sieve analysis, were used to follow the trend of pulverization. Each alloy exhibited a distinct rate of size reduction, particle size distribution, and fracture surface appearance. The results showed that the degree of pulverization substantially increased with increasing tin content. This behavior was attributed to the higher number of machining cracks as well as the increased volume fraction of brittle δ phase in the alloys with higher tin contents. The δ phase was observed to strongly influence the creation of machining cracks as well as the nucleation and propagation of cracks during jet milling. In addition, a direct relationship was observed between the mean δ-phase spacing and the mean size of the jet-milled product; i.e., a decrease in the δ-phase spacing resulted in smaller particles.