Effects of Strain Rate,Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

Through molecular dynamics(MD)simulation,the dependencies of temperature,grain size and strain rate on the mechanical properties were studied.The simulation results demonstrated that the strain rate from 0.05 to 2 ns~(–1 )affected the Young’s modulus of nickel nanowires slightly,whereas the yield stress increased.The Young’s modulus decreased approximately linearly;however,the yield stress firstly increased and subsequently dropped as the temperature increased.The Young’s modulus and yield stress increased as the mean grain size increased from 2.66 to6.72 nm.Moreover,certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension.Certain phenomena such as the formation of twin structures,which were found in nanowires with larger grain size at higher strain rate and lower temperature,as well as the movement of grain boundaries and dislocation,were detected and discussed in detail.The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size.However,for larger grain size,the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.     

Reconsideration on Homogeneous Quadratic Riemann Boundary Value Problem

The homogeneous quadratic Riemann boundary value problem (1) with Hoelder continuous coefficients for the normal case was considered by the author in 1997. But the solutions obtained there are incomplete. Here its general method of solution is obtained.     

Static extracting method of software intended behavior based on API functions invoking

The method of extracting and describing the intended behavior of software precisely has become one of the key points in the fields of software behavior＇s dynamic and trusted authentication. In this paper, the author proposes a specified measure of extracting SIBDS （software intended behaviors describing sets） statically from the binary executable using the software＇s API functions invoking, and also introduces the definition of the structure used to store the SIBDS in detail. Experimental results demonstrate that the extracting method and the storage structure definition offers three strong properties： （i） it can describe the software＇s intended behavior accurately; （ii） it demands a small storage expense; （iii） it provides strong capability to defend against mimicry attack.     

Homology Priority Task Scheduling in μC/OS-Ⅱ Real-Time Kernel

μC/OS-Ⅱ is an open source real-time kernel adopting priority preemptive schedule strategy. Aiming at the problem of μC/OS-Ⅱ failing to support homology priority tasks scheduling, an approach for solution is proposed. The basic idea is adding round-robin scheduling strategy in its original scheduler in order to schedule homology priority tasks through time slice roundrobin. Implementation approach is given in detail. Firstly, the Task Control Block （TCB） is extended. And then, a new priority index table is created, in which each index pointer points to a set of homology priority tasks. Eventually, on the basis of reconstructing μC/OS-Ⅱ real-time kernel, task scheduling module is rewritten. Otherwise, schedulability of homology task supported by modified kernel had been analyzed, and deadline formula of created homology tasks is given. By theoretical analysis and experiment verification, the modified kernel can support homology priority tasks scheduling, meanwhile, it also remains preemptive property of original μC/OS-Ⅱ.     

电子线路的数值优化设计

研究了电子线路的数值化设计方法.它是一种自动化程度高、通用性强、精度高的电路设计方法。介绍了电子线路数值优化设计软件系统YJX—1.它具有广泛的通用性和快速收敛的特点。     

梯形水平折梁的内力分析

本文对梯形水平折梁（０≤α＜∏２）和矩形水平折架（α＝∏２）用最小余能原理进行了内力分析，并导出了相应的计算公式，可在工程结构设计中采用     

产品原理方案的功能设计法──“管接头标记自动压印机”的原理方案设计

本文通过“管接头标记自动压印机”原理方案的构思过程，说明产品原理方案设计的功能论方法的一般原理和特点及其应用。     

约束条件下直动凸轮机构最佳偏距的程序优化

在直动从动件盘形凸轮的设计中，减少推程压力角可改善凸轮的受力条件，适当的偏置可以减少压力角。本文通过计算机设计方法来确定具有最小凸轮机构尺寸时的最佳偏距。     

The harmonic decomposition reconstruction for the exponential radon transform

The exponential Radon transform, a generalization of the Radon transform, is defined and studied as a mapping of function spaces. It is represented in terms of Fourier transform of its domain and range, and this leads to the harmonic decomposition reconstruction. The results are similar results of Tretiak and Metz. Foundation item: Supported by the National Natural Science Foundation of China (No. 19971064), Key Project of Science and Technology of Hubei Province Education Committee. Biography: Wang Jin-ping (1963-), male, Ph.D. candidate, research direction: numberical solution of singular integral equation and integral transformation etc.     

Resource Search in Unstructured Peer-to-Peer System Based on Multiple-Tree Overlay Structure

We propose a multiple-tree overlay structure for resource discovery in unstructured P2P systems. Peers that have similar interests or hold similar type of resources will be grouped into a tree-like cluster. We exploit the heterogeneity of peers in each cluster by connecting peers with more capacities closer to the root of the tree. The capacity of a peer can be defined in different ways （e.g. higher network bandwidth, larger disk space, more data items of a certain type etc.） according to different needs of users or applications.