不同路径等通道转角挤压镁合金的结构与力学性能

为了研究等通道转角挤压时不同工艺路径对镁合金微观结构及性能的影响 ,采用模角φ =12 0°的模具 ,以A ,BA,BC,C四种工艺路径对AZ31镁合金进行了等通道转角挤压 ,分析测试了室温下挤压试样的微观结构及性能 .结果表明 ,相比于A ,BA,C路径挤压 ,BC 路径挤压容易实现较多的挤压道次和变形量 ;多道次挤压后 ,镁合金的晶粒得到显著细化 ,力学性能也显著改善 ,但不同路径的影响不同 .当挤压 12道次时 ,BC,BA 路径挤压试样的屈服强度显著下降 ,延伸率大幅度提高 ;A ,C路径挤压试样的屈服强度变化较小 ,延伸率的提高幅度也小 .     

挤压变形对AZ31镁合金组织和性能的影响

采用500T挤压机试验研究了挤压变形对AZ31镁合金组织和性能的影响。结果表明，挤压变形AZ31镁合金组织以绝热剪切条纹和细小的α再结晶等轴晶为基本特征。挤压变形可显著地细化镁合金晶粒并提高镁合金的力学性能。随挤压比的增大，晶粒细化程度增加，晶粒尺寸由铸态的d400μm减小到挤压态的d12μm（min）；强度、硬度随挤压比的增大而增大，延伸率在挤压比大于16时呈单调减的趋势。     

Mg-6Al-1Sn合金板材的微观组织与力学性能

通过对Mg-6Al-1Sn合金(AT61)进行挤压以及后续的单道次大应变量轧制变形,获得了高强塑性的新型变形镁合金板材.组织分析表明AT61合金中主要析出相为Mg17Al_(12)相和Mg2Sn相,挤压态合金经轧制之后晶粒都被细化,合金强度显著提高.随着应变量的增加,晶粒尺寸先显著降低后有所上升,屈服强度变化规律与晶粒尺寸变化规律一致.经过250℃下的单道次约56%大应变量轧制变形后晶粒尺寸细化最明显(约为4.18μm),合金的屈服强度约为196 MPa,抗拉强度约为294 MPa,延伸率约为26.7%,表现出最优的综合力学性能.     

大应变轧制技术制备细晶AZ31镁合金板材

晶粒细化可以改善镁合金的强度和延性,通过控制轧制工艺可以控制变形组织.文中研究了不同轧制道次变形量对AZ31镁合金组织和性能的影响.实验结果表明:随着轧制道次变形量的增加,轧制应变速率增加,镁合金发生了动态再结晶,获得细小的晶粒组织,板材的硬度增加;但是,当轧制道次变形量增加到一定值之后,板材的表面出现宏观裂纹;采用大的道次轧制应变技术,可以减少轧制道次,制备晶粒尺寸为2～5μm的细晶镁合金板材.     

ECAP挤压L2纯铝的微观组织演化规律

用等通道转角挤压对纯铝L2进行10道次挤压,结果表明：挤压1道次后,原来晶粒尺寸为1 mm的等轴晶沿剪切方向被拉长为条带状晶,在条带状晶粒之间出现被剪切破碎的细小亚晶粒.挤压2道次后,出现了少量等轴晶.挤压4道次后,晶粒取向性变得不太明显,小角度晶界的亚晶粒逐步向大角度晶界的等轴晶演化,晶粒细化到1 μm.随挤压道次的继续增加,晶粒大小不再变化,而形状向等轴状演化.挤压10道次后,合金组织由晶粒大小为1 μm的等轴晶组成.ECAP挤压中,纯剪切变形和应变量的双重作用导致晶粒细化.当晶粒尺寸小于临界尺寸时,剪切变形对晶粒的细化起主要作用;当达到临界尺寸后,应变量起主要作用,表现在使合金组织形貌向等轴晶转变.     

等通道转角挤压对铝青铜合金组织及摩擦学性能的影响

对铝青铜合金(Cu-10%Al-4?)进行了等通道转角挤压(ECAE)热加工处理,研究了ECAE对合金微观组织、力学性能及摩擦学性能的影响.结果表明:ECAE热挤压后合金的晶粒显著细化,晶粒尺寸随着挤压道次的增加而逐步减小;晶粒细化导致合金的硬度与屈服强度显著增加,提高了合金抵抗塑性变形能力,减轻了磨粒对合金表面的犁削作用;ECAE热挤压细化了合金中的第二相,减小了脱落硬质颗粒压入合金表面的深度与宽度,降低了合金的磨损量,提高了合金的摩擦学性能.     

挤压次数对Mg-Zn-Zr-Re合金组织和性能的影响

研究一次与二次挤压变形对添加稀土元素Nd和Y的ZK60镁合金显微组织及力学性能的影响。对加稀土元素Nd和Y的ZK60镁合金在5MN立式挤压机上进行一次与二次挤压,并在国产CSS-44100电子万能拉伸机上进行拉伸试验,采用光学显微镜观察其铸态与变形态显微组织,并在KYKY-2800扫描电镜上观察断口形貌。研究结果表明：经一次挤压后,加入稀土Nd和Y后ZK60镁合金发生动态再结晶晶粒细化,力学性能显著提高,但伸长率较低（在10％以下）;经二次挤压后,在不显著降低合金强度的条件下,其塑性得到明显提高（均在10％以上）。     

等径角挤压对纯铜组织与性能的影响

研究采用BC路径(即试样进入下一道次挤压时按同一方向旋转90°)对纯铜进行等径角挤压后得到的组织与性能.结果表明,通过室温下对纯铜的8道次挤压后,得到均匀、细小的等轴晶组织(晶粒尺寸约1.5μm).抗拉强度从原来的235 MPa提高到420 MPa,硬度从114 HV提高到184.3 HV,延伸率由原来的45%降低到19%.通过对不同挤压道次试样在473 K下60 min的退火处理后,其晶粒进一步细化至1μm,其抗拉强度提高到435 MPa.     

稀土Mg-Mn-Zn-Ce合金等通道转角挤压工艺

为获得性能良好的超细晶镁合金材料,采用等通道转角挤压工艺对稀土Mg—Mn—Zn—Ce合金进行塑性加工,研究了速度、温度和润滑条件对合金的挤压工艺以及性能的影响。实验结果表明：对于稀土Mg—Mn—Zn-Ce合金,等通道转角挤压的润滑剂为7025高温润滑脂,速度2mm／s,第一道次的挤压温度为250℃,第二道次的挤压温度为270℃。该工艺条件使等通道转角挤压能够顺利进行,可获得表面光滑平整、晶粒组织细化的稀土Mg—Mn—Zn—Ce合金。     

AZ91D镁合金组织细化及其对部分重熔半固态组织的影响

通过对熔体进行高强度剪切处理,研究了其对AZ91D镁合金的组织细化作用,获得了不同的铸锭组织,并研究了铸锭初始组织对二次加热后组织的影响.结果表明,熔体高强度剪切处理具有显著的晶粒细化作用,在650℃对熔体高强度剪切处理后,AZ91D镁合金铸锭平均晶粒尺寸由500μm降到170μm.降低熔体处理温度至605℃,组织得到进一步细化,平均晶粒尺寸约为60μm.原始组织大小对二次加热后组织的大小、液相分布具有重要的影响.熔体高强度剪切处理对AZ91D镁合金铸锭的晶粒细化作用在二次加热后能够基本保留下来.在相同的加热条件下,均匀细小的原始组织有利于获得更高的有效液相分数和更趋于球形的晶粒组织.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.