Corrosion behavior of Mg–Y alloy in NaCl aqueous solution

The corrosion behavior of Mg–(0.25, 2.5, 5, 8 and 15)Y alloys in 3.5wt.% NaCl aqueous solution was investigated. It was found that the degree of corrosion deterioration increased with increasing immersion time up to 2 h. Corrosion modes for the alloys with low and high content of Y element were general corrosion and pitting corrosion, respective ly, and the threshold content for the corrosion mode change was 2.5% for the tested alloys. The experimental results showed that the addition of Y refined the grain of the alloy, and the distribution, i.e., continuous or not, of the Mg24Y5 phases had great effect on the corrosion rate and corrosion mode.     

Corrosion behavior of low alloy steels in a wet–dry acid humid environment

The corrosion behavior of corrosion resistant steel (CRS) in a simulated wet–dry acid humid environment was investigated and compared with carbon steel (CS) using corrosion loss, polarization curves, X-ray diffraction (XRD), scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), N₂ adsorption, and X-ray photoelectron spectroscopy (XPS). The results show that the corrosion kinetics of both steels were closely related to the composition and compactness of the rust, and the electrochemical properties of rusted steel. Small amounts of Cu, Cr, and Ni in CRS increased the amount of amorphous phases and decreased the content of γ-FeOOH in the rust, resulting in higher compactness and electrochemical stability of the CRS rust. The elements Cu, Cr, and Ni were uniformly distributed in the CRS rust and formed CuFeO₂, Cu₂O, CrOOH, NiFe₂O₄, and Ni₂O₃, which enhanced the corrosion resistance of CRS in the wet–dry acid humid environment.     

Corrosion-wear behavior of nanocrystalline Fe88Si12 alloy in acid and alkaline solutions

The corrosion-wear behavior of a nanocrystalline Fe₈₈Si₁₂ alloy disc coupled with a Si₃N₄ ball was investigated in acid (pH 3) and alkaline (pH 9) aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe₈₈Si₁₂ alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe₈₈Si₁₂ alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe₈₈Si₁₂ alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si₃N₄ ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe₈₈Si₁₂ alloy in the pH 9 aqueous solution.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

In vitro corrosion of Mg–1.21Li –1.12Ca –1Y alloy

The influence of the microstructure on mechanical properties and corrosion behavior of the Mg–1.21Li–1.12Ca–1Y alloy was investigated using OM, SEM, XRD, EPMA, EDS, tensile tests and corrosion measurements. The results demonstrated that the microstructure of the Mg–1.21Li–1.12Ca–1Y alloy was characterized by α-Mg substrate and intermetallic compounds Mg2 Ca and Mg24Y5. Most of the fine Mg2 Ca particles for the as-cast alloy were distributed along the grain boundaries, while for the as-extruded along the extrusion direction. The Mg24Y5 particles with a larger size than the Mg2 Ca particles were positioned inside the grains. The mechanical properties of Mg–1.21Li–1.12Ca–1Y alloy were improved by the grain refinement and dispersion strengthening. Corrosion pits initiated at the α-Mg matrix neighboring the Mg2 Ca particles and subsequently the alloy exhibited general corrosion and filiform corrosion as the corrosion product layer of Mg(OH)2and Mg CO3 became compact and thick.     

Effects of cupric ions on the corrosion behavior of aluminum alloy 5A02 in ethylene glycol-water solution

The effects of cupric ions on the corrosion behavior of aluminum alloy 5A02 in ethylene glycol-water solutions were studied by potentiodynamic polarization, electrochemical noise (EN), and complementary techniques including scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). A positive corrosion potential and increased corrosion current were observed due to the deposition of copper. The results demonstrate that the main corrosion type was pitting and the increasing cupric ion concentration augmented the pitting density. The pits became larger and deeper as a result of the embedment of copper into the surface of the alloy. Cupric ions were preferentially deposited at the defects around the secondary phase, leading to the formation of Al-Cu microgalvanic couples, which increased the corrosion rate. The corrosion rate gradually reached a stable value as the concentration of cupric ions was increased beyond 10 mmol/L.