Vertex disjoint cycles in intersection graphs of bases of matroids

The intersection graph of bases of a matroid M=(E, B) is a graph G=G~I(M) with vertex set V(G) and edge set E(G) such that V(G)=B(M) and E(G)={BB′:|B∩B′|≠0, B, B′∈B(M), where the same notation is used for the vertices of G and the bases of M. Suppose that|V(G~I(M))| =n and k_1+k_2+…+k_p=n, where k_i is an integer, i=1, 2,…, p. In this paper, we prove that there is a partition of V(G~I(M)) into p parts V_1 , V_2,…, V_p such that |V_i| =k_i and the subgraph H_i induced by V_i contains a k_i-cycle when k_i ≥3, H_i is isomorphic to K_2 when k_i =2 and H_i is a single point when k_i =1.     

Effects of applied potential on the stress corrosion cracking behavior of 7003 aluminum alloy in acid and alkaline chloride solutions

Potentiodynamic polarization tests and slow strain rate test (SSRT) in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) in acid and alkaline chloride solutions under various applied potentials (E_a). The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution (AD) at open-circuit potential (OCP) and is highly susceptible to hydrogen embrittlement (HE) at high negative E_a in the solutions with pH levels of 4 and 11. The susceptibility increases with negative shift in the potential when E_a is less than -1000 mV vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when E_a is equal to -1000 mV vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.     

Reduction in secondary dendrite arm spacing in cast eutectic Al-Si piston alloys by cerium addition

The effects of Ce on the secondary dendrite arm spacing (SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis (CA CCTA). -The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, △T_S, and low solidification temperature, △T_S, whereas 0.1wt% Ce resulted in a fast solidification time, △ta-Al, of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index (Q) and ultimate tensile strength of (UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.     

Binding number,minimum degree and bipancyclism in bipartite graphs

Let G =(V_1,V_2,E) be a balanced bipartite graph with2 n vertices.The bipartite binding number of G,denoted by B(G),is defined to be n if G =K_n and min i∈{1,2}|N(S)|n min |N(S)|/|S|otherwise.We call G bipancyclic if it contains a cycle of every even length m for 4 ≤ m ≤ 2n.A theorem showed that if G is a balanced bipartite graph with 2n vertices,B(G) 3 / 2 and n 139,then G is bipancyclic.This paper generalizes the conclusion as follows:Let 0 c 3 / 2 and G be a 2-colmected balanced bipartite graph with 2n(n is large enough) vertices such that B(G) c and δ(G)(2-c)n/(3-c)+2/3.Then G is bipancyclic.     

Highly <Emphasis Type="Italic">C</Emphasis>-axis oriented LiNbO<Subscript>3</Subscript> thin film on amorphous SiO<Subscript>2</Subscript> buffer layer and its growth mechanism

LiNbO3 waveguiding films with highly C-axis orieatation and superior crystallographic quality have been deposited on the amorphous SiO2 buffer layer of Si wafer by pulsed laser deposition (PLD) technique. X-ray diffraction,high-resolution electron transmission microscopy and atomic force microscopy were applied to characterizing the quality and orientaion of LiNbO3 thin film, and the optimized depositioa coaditioas have been determined for C-axis oriented growth. LiNbO3 thin films on amorphous SiO2 buffer layer were composed of intimate arrangements of quadrangular single crystal domain (150 nm x 150 nm) with C-axis orientatioa, and displayed sharp interface structures. The measurements of prism coupling technique indicate that the laser can be coupled into the LiNbO3 film and TE and TM waveguiding modes were detected. In addition, the possible mechanism of oriented growth on amorphous buffer layer and “film-substrate effects“ were discussed briefly, which suggests that its growth mechanism is likely analogous to the Voimer model with characteristics of three-dimensional islands nucleation on the smooth crystal surface.     

Properties of a class of groups on <Emphasis Type="Italic">Z</Emphasis><Subscript><Emphasis Type="Italic">m</Emphasis></Subscript>

In this paper, we obtain the factorization of direct production and order of group GL(n, Z _m ) in a simple method. Then we generalize some properties of GL(2, Z _p ) proposed by Huppert, and prove that the group \(GL\left( {2,{Z_{{z^\lambda }}}} \right)\) is solvable. We also prove that group GL(n, Z _p ) is solvable if and only if GL(n, Z _p ) is solvable, and list the generators of groups GL(n, Z _p ) and SL(n, Z _p ). At last, we prove that PSL(2, Z _p )(p > 3) and PSL(n, Z _p )(n > 3) are simple.     

A generalized funk’s section theorem for measures

If L is a star body in R~n whose central(n-i)-slices have the same(n-i)-dimensional measure μ_(n-i)(with appropriate density)as the central(n-i)-slices of an origin-symmetric star body K,then the corresponding n-dimensional measures μ_n of K and L satisfy μ_n(K)≤μ_n(L).This extends a generalized Funk’s section theorem for volumes to that for measures.     

Gracefulness of several unconnected graphs with wheel

In the paper, we study the gracefulness of several unconnected graphs related to wheel. For natural number p ≥1,t ≥1, let n =2t +3, 2t +4, which proved W_n∪K_(p,t)~(1)∪K_(p,t)~(2) is graceful; for p ≥1, t ≥1,let n=2t+3,2t+4, then W_(n,2n+1)∪K_(p,t)~(1)∪K_(p,t)~(2) is graceful and for m≥1,r ≥1, let n =2m +5, W_(n,2n+1) ∪( C_3∨K m) U St( r)is graceful.     

Research on a Class of Equations over Finite Fields

Let F_q stand for the finite field of odd characteristic p with q elements(q=p~n,n∈N)and F_q~* denote the set of all the nonzero elements of F_q.In this paper,by using the augmented degree matrix and the result given by Cao,we obtain a formula for the number of rational points of the following equation over F_q:f(x _1,x _2,...,x _n)=(a_1 x_1 x_2~d+a_2 x_2 x_3~d...+a_(n-1)x_(n-1)x_n~d+a_n x_n x_1~d)~λ-bx_1~(d1)x_2~d2...x_n~(dn),with a_i,b∈F_q~*,n≥2,λ0 being positive integers,and d,d_i being nonnegative integers for 1≤i n.This technique can be applied to the polynomials of the form h_1~λ=h_2 with λ being positive integer and h_1,h_2∈F_q[x _1,x _2,...,x _n].It extends the results of the Markoff-Hurwitz-type equations.     

Dissolution characteristics of sericite in chalcopyrite bioleaching and its effect on copper extraction

The effects of sericite particle size, rotation speed, and leaching temperature on sericite dissolution and copper extraction in a chalcopyrite bioleaching system were examined. Finer particles, appropriate temperature and rotation speed for Acidithiobacillus ferrooxidans resulted in a higher Al3+ dissolution concentration. The Al3+ dissolution concentration reached its highest concentration of 38.66 mg/L after 48-d leaching when the sericite particle size, temperature, and rotation speed were -43 μm, 30℃, and 160 r/min, respectively. Meanwhile, the sericite particle size, rotation speed, and temperature can affect copper extraction. The copper extraction rate is higher when the sericite particle size is finer. An appropriately high temperature is favorable for copper leaching. The dissolution of sericite fitted the shrinking core model, 1-(2/3)α-(1-α)2/3=k₁t, which indicates that internal diffusion is the decision step controlling the overall reaction rate in the leaching process. Scanning electron microscopy analysis showed small precipitates covered on the surface of sericite after leaching, which increased the diffusion resistance of the leaching solution and dissolved ions.     

Influences of the shape of magnetic material on the magnetoelectric properties of the PZT/Metglas composite

In this paper, the influences of the shape of magnetic material on the magnetoelectric(ME) properties of PZT/Metglas magnetoelectric(ME) composites have been investigated. The results indicate that, with the decrease of the waist length(L_w) of the dumbbell-shaped Metglas, the magnetic flux density in the center region and ME coefficients(α_(ME)) of the composites increase, while the optimal bias magnetic field Hdc decreases on the contrary. In an AC magnetic field of 1 kHz, the maximum αME(α_(Max)) of the composite with L_w= 20 mm exhibits 1.3 times larger than that of the one with L_w=50 mm, and the optimal Hdc deceases by 15%. At the resonant frequencies of each composites, α_(Max) is enhanced by 1.3 times as L_w decreases from 50 to 20 mm. The simulation made by Comsol Multiphysics and the theoretical analysis based on an equivalent magnetic circuit confirm the experimental results.     

Fault-tolerant cycles embedding in folded hypercubes

The generalized conditional fault-tolerant embedding is investigated, in which the n-dimensional folded hypercube networks(denoted by FQ_n) acts as the host graph, and the longest fault-free cycle represents the guest graph. Under the conditions looser than that of previous works, it is shown that FQ_n has a cycle with length at least 2~n-2︱F_v︱ when the number of faulty vertices and non-critical edges is at most 2n-4; where ︱F_v︱ is the number of faulty vertices. It provides further theoretical evidence for the fact that FQ_n has excellent node-fault-tolerance and edge-fault-tolerance when used as a topology of large scale computer networks.     

Lüroth Expansion Digits and Maclaurin's Inequality

It is well known that for almost all real number x, the geometric mean of the first n digits d_i(x) in the Lüroth expansion of x converges to a number K_0 as n→∞. On the other hand, for almost all x, the arithmetric mean of the first n Lüroth expansion digits d_i(x) approaches infinity as n→∞. There is a sequence of refinements of the AM-GM inequality, Maclaurin's inequalities, relating the 1/k-th powers of the k-th elementary symmetric means of n numbers for 1≤k≤n. In this paper, we investigate what happens to the means of Lüroth expansion digits in the limit as one moves f(n) steps away from either extreme. We prove sufficient conditions on f(n) to ensure divergence when one moves away from the arithmetic mean and convergence when one moves f(n) steps away from geometric mean.     

Global Existence and Optimal Decay Rate of the Compressible Magnetohydrodynamic Equation with Potential Force

In this paper, we consider the three dimensional compressible viscous magnetohydrodynamic equations(MHD) with the external potential force. We first derive the corresponding non-constant stationary solutions. Next, we show global wellposedness of the initial value problem for the three dimensional compressible viscous magnetohydrodynamic equations, provided that the initial data is close to the stationary solution. Finally, based on the elaborate energy estimates for the nonlinear system and L~p-L~q decay estimates of the linearized equation, we show the optimal convergence rates of the solution in L~q-norm with 2≤q≤6 and its first derivative in L~2-norm when the initial perturbation is bounded in L~p-norm with 1≤p6/5.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

On the Dual <Emphasis Type="Italic">p</Emphasis>-Measures of Asymmetry for Star Bodies

Recently, the connection between p-measures of asymmetry and the L_p -mixed volumes for convex bodies was found soon after the p-measure of asymmetry was proposed, and the Orlicz-measures of asymmetry was proposed inspired by such a kind of connection. In this paper, by a similar way the dual p -measures of asymmetry for star bodies (naturally for convex bodies) is introduced first. Then the connection between dual p -measures of asymmetry and L_p -dual mixed volumes is established. Finally, the best lower and upper bounds of dual p-measures and the corresponding extremal bodies are discussed.     

Molecular phylogenetics of <Emphasis Type="Italic">Gymnocypris</Emphasis> (Teleostei: Cyprinidae) in Lake Qinghai and adjacent drainages

149 complete mitochondrial DNA (mtDNA) cytochrome b (Cyt b) genes (1140 bp) of Gymnocypris przewalskii, Gymnocypris eckloni and Gymnocypris scolistomus from the Lake Qinghai, Yellow River and Qaidam Basin were sequenced and analyzed. Consistent dendrogram indicated that the samples collected from the same species do not constitute a separate monophyletic group and all the samples were grouped into three highly divergent lineages (A, B and C). Among them, Lineage A contained all samples of G. przewalskii from the Lake Qinghai and partial samples of the G. eckloni from the Yellow River. Lineage B contained the remaining samples of G. eckloni from the Yellow River. Lineage C was composed of a monophyletic group by G. eckloni from the Qaidam Basin. Analysis of molecular variance (AMOVA) indicated that most of genetic variations were detected within these three mtDNA lineages (93.12%), suggesting that there are three different lineages of Gymnocypris in this region. Our Cyt b sequence data showed that G. przewalskii was not a polytypic species, and G. scolistomus was neither an independent species nor a subspecies of G. eckloni. The divergent mtDNA lineages of G. eckloni from the Yellow River suggested that gene flow between the different populations was restricted to a certain extent by several gorges on the upper reach of the Yellow River. Lineage B of G. eckloni might be the genetic effect from the ancestor which was incorporated with the endemic schizothoracine fishes when the headward erosion of the Yellow River reached to its current headwaters of late. The G. eckloni from Basin Qaidam was a monophyletic group (lineage C) and F_st values within G. eckloni from the Yellow River were higher than 0.98, suggesting that the gene flow has been interrupted for a long time and the G. eckloni from Basin Qaidam might have been evolved into different species by ecology segregation. The correlation between the rakers number of Gymnocypris and population genetic variation was not significant. All Gymnocypris populations exhibited a low nucleotide diversity (π = 0.00096–0.00485). Therefore the Gymnocypris populations from Basin Qaidam could have experienced severe bottleneck effect in history. Our result suggested Gymnocypris populations of Basin Qaidam should give a high priority in conservation programs.     

Parameter-Dependent Third-Order Susceptibility of InxGa1-xN/GaN Parabolic Quantum Dots

The electron states confined in wurtzite InxGa1-xN/GaN strained quantum dots （QDs） have been investigated in the effective -mass approximation by solving the Schrtdinger equation, in which parabolic confined potential and strong built-in electric field effect （due to the piezoelectricity and spontaneous polarization） have been taken into account. The real part Rex^（3）（0,0,ω） and the imaginary part Imx^（3）（0,0,ω） of the third-order susceptibil- ity describe quadratic electro-optic effects and electro-absorption process of the QDs respectively. And both of them have been calculated in directions parallel and vertical to z axis. Furthermore, the study shows Rex^（3）（0,0,ω） and Imx^（3）（0,0,ω） increase under resonant conditions with the QDs＇ radius and height increase, and the same results occur when the content increase. In addition, the resonant position shift to the lower energy region when the parabolic frequencies increase.     

The Reverse Hoelder Classes in Martingale Setting

In martingale setting, it has been shown that Ap weights can be factorized in terms of A1 weights. This factorization benefits many problems very much. ]n this paper, the new class of RH~ plays the same role for RHs, which makes the reverse HOlder inequalities hold with exponent s＞1, that the class A1 does for Ap class. Therefore, the Jones‘ factorization theorem for Ap weights was extended to include some information about the reverse HOlder classes. And it is the most convenient obiect in weight theory indeed.     

Generalized Intersection Bodies with Parameter

AIn 2005, the classical intersection bodies and L_p intersection bodies were extended. Afterwards, the concept of general L_p intersection bodies and the generalized intersection bodies was introduced. In this paper, we define the generalized bodies with parameter. Besides, we establish the extremal values for volume, Brunn-Minkowski type inequality for radial combination and L_p harmonic Blaschke combination of this notion.