Comparative study on the corrosion behavior of X52, 3Cr,and 13Cr steel in an O_2–H_2O–CO_2 system: products,reaction kinetics,and pitting sensitivity

The corrosion behaviors of X52, 3Cr low-alloy steel, and 13Cr stainless steel were investigated in an O_2–H2O–CO_2 environment at various temperatures and O_2–CO_2 partial-pressure ratios. The results showed that the corrosion rates of X52, 3Cr, and 13Cr steels increased with increasing temperature. The corrosion rates slowly increased at temperatures less than 100°C and increased sharply when the temperature exceeded 100°C. In the absence of O_2, X52, 3Cr, and 13Cr exhibited uniform corrosion morphology and Fe CO3 was the main corrosion product. When O_2 was introduced into the system, various forms of Fe_2O_3 appeared on the surface of the samples. The Cr content strongly influenced the corrosion resistance. The 3Cr steel with a low Cr content was more sensitive to pitting than the X52 or 13Cr steel. Thus, pitting occurred on the surface of 3Cr when 1.25 MPa of O_2 was added; this phenomenon is related to the non-uniform distribution of Crin 3Cr.     

Passivation method of 317L stainless steel used in medicine

The electrochemical performance of 317L stainless steel used in medicine under different conditions of passivation (different contents of HNO₃ solution, different passivation time and different passivation temperatures) was studied. The results show that the pitting potential of 317L stainless steel used in medicine can reach about 1.0 V (SCE) when electrochemically tested in 0.9% NaCl solution after the steel was passivated in 30% HNO₃ solution at 35℃ for 6 h, which indicates that the passivation film has a relatively strong resistance to corrosion. The results also show that the corrosion resistance of the passivation film on the surface of 317SS can be increased after suitable amount of K₂Cr₂O₇ is added into HNO₃ passivation solution.     

Effects of silty sand on CO<Subscript>2</Subscript> corrosion behavior of low-Cr tubing steel

An experimental study was carried out to assess the effects of silty sand on the CO 2 corrosion behavior of 1 wt% Cr (1Cr) and 3 wt% Cr (3Cr) tubing steel under 0.5 MPa CO 2 at 100°C and 1.5 m/s flow velocity.The 1Cr and 3Cr specimens both suffered general corrosion,but the surface was coarser in the pure CO 2 corrosion environment.Under silty sand conditions,severe pitting corrosion occurred on the 1Cr specimens and some acicular pitting appeared on the 3Cr specimens.The average corrosion rates of 1Cr and 3Cr steels increased by factors of 3 and 1.6,respectively.The corrosion products were analyzed by scanning electron microscopy (SEM),energy dispersive spectroscopy (EDS),X-ray diffraction (XRD),and electrical impedance spectroscopy (EIS).The results show that silty sand acts as an inclusion in corrosion product films and reduces the homogeneity and density of the products,rather than abrading the corrosion film.Ion-diffusion channels may build up around the irregular silty sand;this would degrade the protective capabilities of the product films and aggravate corrosion.     

Relationship between the specific surface area of rust and the electrochemical behavior of rusted steel in a wet-dry acid corrosion environment

The relationship between the specific surface area (SSA) of rust and the electrochemical behavior of rusted steel under wet-dry acid corrosion conditions was investigated. The results showed that the corrosion current density first increased and then decreased with increasing SSA of the rust during the corrosion process. The structure of the rust changed from single-layer to double-layer, and the γ-FeOOH content decreased in the inner layer of the rust with increasing corrosion time; by contrast, the γ-FeOOH content in the outer layer was constant. When the SSA of the rust was lower than the critical SSA corresponding to the relative humidity during the drying period, condensed water in the micropores of the rust could evaporate, which prompted the diffusion of O₂ into the rust and the following formation process of γ-FeOOH, leading to an increase of corrosion current density with increasing corrosion time. However, when the SSA of the rust reached or exceeded the critical SSA, condensate water in the micro-pores of the inner layer of the rust could not evaporate which inhibited the diffusion of O₂ and decreased the γ-FeOOH content in the inner rust, leading to a decrease of corrosion current density with increasing corrosion time.     

Corrosion behavior of low alloy steels in a wet–dry acid humid environment

The corrosion behavior of corrosion resistant steel (CRS) in a simulated wet–dry acid humid environment was investigated and compared with carbon steel (CS) using corrosion loss, polarization curves, X-ray diffraction (XRD), scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), N₂ adsorption, and X-ray photoelectron spectroscopy (XPS). The results show that the corrosion kinetics of both steels were closely related to the composition and compactness of the rust, and the electrochemical properties of rusted steel. Small amounts of Cu, Cr, and Ni in CRS increased the amount of amorphous phases and decreased the content of γ-FeOOH in the rust, resulting in higher compactness and electrochemical stability of the CRS rust. The elements Cu, Cr, and Ni were uniformly distributed in the CRS rust and formed CuFeO₂, Cu₂O, CrOOH, NiFe₂O₄, and Ni₂O₃, which enhanced the corrosion resistance of CRS in the wet–dry acid humid environment.     

Fabrication of high nitrogen austenitic stainless steels with excellent mechanical and pitting corrosion properties

A series of high nitrogen austenitic stainless steels were successfully developed with a pressurized electroslag remelting furnace. Nitride additives and deoxidizer were packed into the stainless steel pipes, and then the stainless steel pipes were welded on the surface of an electrode with low nitrogen content to prepare a compound electrode. Using Si₃N₄ as a nitrogen alloying source, the silicon contents in the ingots were prone to be out of the specification range, the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved with FeCrN as a nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen content of 1.21wt% can be obtained. The 18Cr18Mn2Mo0.9N high nitrogen austenitic stainless steel exhibits high strength and good ductility at room temperature. The steel shows typical ductile-brittle transition behavior and excellent pitting corrosion resistance properties.     

Flow-accelerated corrosion behavior of 13Cr stainless steel in a wet gas environment containing CO<Subscript>2</Subscript>

This work investigated the flow-accelerated corrosion (FAC) behavior of 13Cr in a wet CO₂-containing environment at different flowing gas velocities and impinging angles, with the natural-gas pipeline environment simulated by a self-assembled impingement jet system. Surface morphology determination, electrochemical measurements, and hydromechanics numerical analysis were carried out to study the FAC behavior. The results demonstrate that pitting corrosion was the primary mode of corrosion in 13Cr stainless steel. High-flow-rate gas destroyed the passive film and decreased the pitting potential, resulting in more serious corrosion. The corrosion degree with various impact angles showed the following order: 90° > 60° > 45°. The shear force and the electrolyte from the flowing gas were concluded to be the determinant factors of FAC, whereas the shear force was the main factor responsible for destroying the passive film.     

Glass-forming ability,microhardness, corrosion resistance,and dealloying treatment of Mg60-xCu40Ndx alloy ribbons

The influence of Nd addition on the glass-forming ability (GFA), microhardness, and corrosion resistance of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25, at%) alloys were investigated by differential scanning calorimetry, Vickers-type hardness tests, and electrochemical methods. The results suggest that the GFA and microhardness of the amorphous alloys increase until the Nd content reaches 20at%. The corrosion potential and corrosion current density obtained from the Tafel curves indicate that the Mg₃₅Cu₄₀Nd₂₅ ternary alloy exhibits the best corrosion resistance among the investigated alloys. Notably, nanoporous copper (NPC) was synthesized through a single-step dealloying of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25) ternary alloys in 0.04 mol·L-1 H₂SO₄ solution under free corrosion conditions. The influence of dealloying process parameters, such as dealloying time and temperature, on the microstructure of the ribbons was also studied using the surface diffusivity theory. The formation mechanism of dealloyed samples with a multilayered structure was also discussed.     

9Cr?5Si?3Al铁素体耐热钢的高温氧化行为

To improve the oxidation properties of ferritic heat-resistant steels, an Al-bearing 9Cr?5Si?3Al ferritic heat-resistant steel was designed. We then conducted cyclic oxidation tests to investigate the high-temperature oxidation behavior of 9Cr?5Si and 9Cr?5Si?3Al ferritic heat-resistant steels at 900 and 1000°C. The characteristics of the oxide layer were analyzed by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The results show that the oxidation kinetics curves of the two tested steels follow the parabolic law, with the parabolic rate constant k_p of 9Cr?5Si?3Al steel being much lower than that of 9Cr?5Si steel at both 900 and 1000°C. The oxide film on the surface of the 9Cr?5Si alloy exhibits Cr₂MnO₄ and Cr₂O₃ phases in the outer layer after oxidation at 900 and 1000°C. However, at oxidation temperatures of 900 and 1000°C, the oxide film of the 9Cr?5Si?3Al alloy consists only of Al₂O₃ and its oxide layer is thinner than that of the 9Cr?5Si alloy. These results indicate that the addition of Al to the 9Cr?5Si steel can improve its high-temperature oxidation resistance, which can be attributed to the formation of a continuous and compact Al₂O₃ film on the surface of the steel.     

Corrosion properties of bio-oil and its emulsions with diesel

Bio-oil is a new liquid fuel but very acidic. In this study, bio-oil pyrolyzed from rice husk and two bio-oil/diesel emulsions with bio-oil concentrations of 10 wt% and 30 wt% were prepared. Tests were carried out to determine their corrosion properties to four metals of aluminum, brass, mild steel and stainless steel at different temperatures. Weight loss of the metals immersed in the oil samples was recorded. The chemical states of the elements on metal surface were analyzed by X-ray photoelectron spectroscopy （XPS）. The results indicated that mild steel was the least resistant to corrosion, followed by aluminum, while brass exhibited slight weight loss. The weight loss rates would be greatly enhanced at elevated temperatures. Stainless steel was not affected under any conditions. After corrosion, in- creased organic deposits were formed on aluminum and brass, but not on stainless steel. Mild steel was covered with many loosely attached corrosion materials which were easy to be removed by washing and wiping. Significant metal loss was detected on surface of aluminum and mild steel. Zinc was etched away from brass surface, while metallic copper was oxidized to Cu20. Increased Cr203 and NiO were presented on surface of stainless steel to form a compact passive protection film. The two emulsions were less corrosive than the bio-oU. This was due to the protection effect of diesel. Diesel was the continuous phase in the emulsions and thus could limit the contact area between bio-oil and metals.     

Comparative study on the corrosion behavior of X52, 3Cr,and 13Cr steel in an O2–H2O–CO2 system: products,reaction kinetics,and pitting sensitivity

The corrosionbehaviors of X52, 3Cr low-alloy steel, and 13Cr stainless steel were investigated inanO2–H2O–CO2 environment at varioustemperaturesand O2–CO2partial-pressure ratios. The results showed thatthe corrosion rates of X52, 3Cr, and 13Cr steels in-creased with increasing temperature. The corrosion ratesslowly increased at temperaturesless than100℃ and increased sharply when the temperature exceeded100℃. In the absence of O2, X52, 3Cr, and 13Cr exhibited uniform corrosion morphology and FeCO3 was the main corrosion product. When O2 was introduced into the system, various forms of Fe2O3 appeared on the surface of the samples. The Cr content strongly influenced the corrosion resistance. The 3Cr steel with a low Cr content was more sensitive to pitting than the X52 or 13Cr steel. Thus, pitting occurred on the surface of 3Cr when 1.25 MPa of O2 was added; this phenomenon is related to the non-uniform distribution of Cr in 3Cr.     

Mineral-phase evolution and sintering behavior of MO-SiO2-Al2O3-B2O3 (M=Ca,Ba) glass-ceramics by low-temperature liquid-phase sintering

In this work, network former SiO₂ and network intermediate Al₂O₃ were introduced into typical low-melting binary compositions CaO·B₂O₃, CaO·2B₂O₃, and BaO·B₂O₃ via an aqueous solid-state suspension milling route. Accordingly, multiple-phase aluminosilicate glass-ceramics were directly obtained via liquid-phase sintering at temperatures below 950℃. On the basis of liquid-phase sintering theory, mineral-phase evolutions and glass-phase formations were systematically investigated in a wide MO-SiO₂-Al₂O₃-B₂O₃ (M=Ca, Ba) composition range. The results indicate that major mineral phases of the aluminosilicate glass-ceramics are Al₂₀B₄O₃₆, CaAl₂Si₂O₈, and BaAl₂Si₂O₈ and that the glass-ceramic materials are characterized by dense microstructures and excellent dielectric properties.     

Investigation of the deterioration of passive films in H<Subscript>2</Subscript>S-containing solutions

The effect of H₂S on the corrosion behavior of 316L stainless steel was investigated using electrochemical methods by changing the gas condition from CO₂ to H₂S and then back to CO₂. The presence of H₂S showed an acceleration effect on the corrosion of 316L stainless steel in comparison with CO₂. The acceleration effect remained even after the complete removal of H₂S by CO₂, indicating that the passive film was irreversibly damaged. X-ray photoelectron spectroscopy (XPS) analysis indicated that the passive film was composed of Cr₂O₃, Fe₂O₃, and FeS₂ after being immersed in H₂S-containing solutions. The semiconducting property of the passive film was then investigated by using the Mott-Schottky approach. The presence of sulfides resulted in higher acceptor and donor densities and thus was responsible for the deterioration of passive films.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

Synthesis of LiCo<Subscript>0.3</Subscript>Ni<Subscript>0.7</Subscript>O<Subscript>2</Subscript> as cathode materials for lithium ion batteries by citric acid-assisted sol-gel method

The synthesis process of LiCo0.3Ni0.7O2 was investigated by FT-IR, mass spectroscopy, elemental analysis, SEM, BET, TG/DTA and XRD in this paper. The results revealed that lithium and transition metal ions were trapped homogeneously on an atomic scale throughout the precursor. Li2CO3, NiO and CoO are the intermediate products obtained after decomposition of the precursor and Li2CO3 undergoes direct reactions with NiO and CoO to form LiCo0.3Ni0.7O2. Moreover, the kinetics of formation of LiCo0.3Ni0.7O2 by dtrate sol-gel method is faster than the case of the conventional solid-state reaction between lithium carbonate and corresponding reactants. The single phase of LiCo0.3Ni0.7O2 was synthesized at temperature as low as 550℃. The discharge capacity of LiCo0.3Ni0.7O2 increases from 127 to 185 mAh/g as the caldnation temperature increasing from 550 to 750℃. After 100 cycles, the discharge capacity of the sample calcined at 750℃ is 155 mAh/g. The electrochemical study shows that the LiCo0.3Ni0.7O2 has high discharge capacity and good cycling behavior for lithium ion batteries.     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

Fabrication and properties of aluminum silicate fibrous materials with <Emphasis Type="Italic">in situ</Emphasis> synthesized K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> whiskers

To improve their mechanical and thermal insulation properties, aluminum silicate fibrous materials with in situ synthesized K₂Ti₆O₁₃ whiskers were prepared by firing a mixture of short aluminum silicate fibers and gel powders obtained from a sol-gel process. During the preparation process, the fiber surface was coated with K₂Ti₆O₁₃ whiskers after the fibers were subjected to a heat treatment carried out at various temperatures. The effects of process parameters on the microstructure, compressive strength, and thermal conductivity were analyzed systematically. The results show that higher treatment temperatures and longer treatment durations promoted the development of K₂Ti₆O₁₃ whiskers on the surface of aluminum silicate fibers; in addition, the intersection structure between whiskers modulated the morphology and volume of the multi-aperture structure among fibers, substantially increasing the fibers' compressive strength and reducing their heat conduction and convective heat transfer at high temperatures.     

Characteristics of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, MnS,and TiN inclusions in the remelting process of bearing steel

The Al₂O₃, MnS, and TiN inclusions in bearing steel will deteriorate the steel's mechanical properties. Therefore, elucidating detailed characteristics of these inclusions in consumable electrode during the electroslag remelting process is important for achieving a subsequently clean ingot. In this study, a confocal scanning violet laser microscope was used to simulate the remelting process and observe, in real time, the behaviors of inclusions. The obtained images show that, after the temperature exceeded the steel solidus temperature, MnS and TiN inclusions in the specimen began to dissolve. Higher temperatures led to faster dissolution, and the inclusions disappeared before the steel was fully liquid. In the case of an observed Al₂O₃ inclusion, its shape changed from angular to a smooth ellipsoid in the region where the solid and liquid coexisted and it began to dissolve as the temperature continued to increase. This dissolution was driven by the difference in oxygen potential between the inclusion and the liquid steel.