Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

功能梯度Ni?W/Er2O3稀土纳米颗粒复合膜的电沉积

Multi-layered functionally graded (FG) structure Ni?W/Er₂O₃ nanocomposite films were prepared by continuously changing the deposition parameters, in which the Er₂O₃ and W contents varied with thickness. The microstructure and chemical composition of the electrodeposited Ni?W/Er₂O₃ films were determined by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The anti-corrosion and wear properties of the electrodeposition films were investigated by electrochemical measurement and ball-on-disk friction test. The microhardness distribution of the cross section of nanocomposites was measured by nanoindentation. The results showed that with decreasing agitation rate or increasing average current density, the contents of Er₂O₃ nanoparticles and tungsten were distributed in a gradient along the thickness, and the contents on the surface were larger. By comparison, FG Ni?W/Er₂O₃ films had better anti-corrosion and wear properties than the uniform Ni?W/Er₂O₃ films. Atomic force microscopy (AFM) and profilometry measurements indicated that Er₂O₃ nanoparticles had an effect on the surface roughness.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> magnetic composite nanoparticles by a one-pot process

Fe₃O₄@SiO₂ core–shell composite nanoparticles were successfully prepared by a one-pot process. Tetraethyl-orthosilicate was used as a surfactant to synthesize Fe₃O₄@SiO₂ core–shell structures from prepared Fe₃O₄ nanoparticles. The properties of the Fe₃O₄ and Fe₃O₄@SiO₂ composite nanoparticles were studied by X-ray diffraction, transmission electron microscopy, energy dispersive spectroscopy, and Fourier transform infrared spectroscopy. The prepared Fe₃O₄ particles were approximately 12 nm in size, and the thickness of the SiO₂ coating was approximately 4 nm. The magnetic properties were studied by vibrating sample magnetometry. The results show that the maximum saturation magnetization of the Fe₃O₄@SiO₂ powder (34.85 A·m2·kg–1) was markedly lower than that of the Fe₃O₄ powder (79.55 A·m2·kg–1), which demonstrates that Fe₃O₄ was successfully wrapped by SiO₂. The Fe₃O₄@SiO₂ composite nanoparticles have broad prospects in biomedical applications; thus, our next study will apply them in magnetic resonance imaging.     

Enhanced microwave absorption properties of rod-shaped Fe2O3/Fe3O4/ MWCNTs composites

A novel type of composite absorber,i.e.Fe_2O_3/Fe_3O_4/MWCNTs composites(0%,1.7%and 5%MWCNTs),with microwave absorption properties was successfully fabricated by a facile hydrothermal method.The preparedα-Fe_2O_3/Fe_3O_4nanoparticles displayed rod-shaped morphology.The complex permittivity and permeability of the Fe_2O_3/Fe_3O_4/MWCNTs composites distinctly increased,furthermore,with the introduction of MWCNTs,the Fe_2O_3/Fe_3O_4/MWCNTs composites exhibited fine microwave absorption performance with strong absorption and wide absorption band.In particular,for Fe_2O_3/Fe_3O_4/1.7%MWCNTs composite with an absorber thickness of 2.5 mm,the reflection loss(RL)reached a minimum of-44.1 d B at 10.4 GHz and the effective absorption bandwidth(RL-10 d B)covered 3.3 GHz.The enhanced microwave absorption performance of the Fe_2O_3/Fe_3O_4/MWCNTs composites was attributed to the high dielectric loss and improved impedance matching which was closely related to the rod-shaped morphology of Fe_2O_3,Fe_3O_4and the introduction of MWCNTs.     

Synthesis and application of bilayer-surfactant-enveloped Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles: water-based bilayer-surfactant-enveloped ferrofluids

Superparamagnetic carbon-coated Fe₃O₄ nanoparticles with high magnetization (85 emu·g-1) and high crystallinity were synthesized using polyethylene glycol-4000 (PEG (4000)) as a carbon source. Fe₃O₄ water-based bilayer-surfactant-enveloped ferrofluids were subsequently prepared using sodium oleate and PEG (4000) as dispersants. Analyses using X-ray photoelectron spectroscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy indicate that the Fe₃O₄ nanoparticles with a bilayer surfactant coating retain the inverse spinel-type structure and are successfully coated with sodium oleate and PEG (4000). Transmission electron microscopy, vibrating sample magnetometry, and particle-size analysis results indicate that the coated Fe₃O₄ nanoparticles also retain the good saturation magnetization of Fe₃O₄ (79.6 emu·g-1) and that the particle size of the bilayer-surfactant-enveloped Fe₃O₄ nanoparticles is 42.97 nm, which is substantially smaller than that of the unmodified Fe₃O₄ nanoparticles (486.2 nm). UV–vis and zeta-potential analyses reveal that the ferrofluids does not agglomerate for 120 h at a concentration of 4 g·L-1, which indicates that the ferrofluids are highly stable.     

Reaction mechanism for in-situ β-SiAlON formation in Fe3Si-Si3N4-Al2O3 composites

In this work, Fe₃Si-Si₃N₄-Al₂O₃ composites were prepared at 1300℃ in an N₂ atmosphere using fused corundum and tabular alumina particles, Al₂O₃ fine powder, and ferrosilicon nitride (Fe₃Si-Si₃N₄) as raw materials and thermosetting phenolic resin as a binder. The effect of ferrosilicon nitride with different concentrations (0wt%, 5wt%, 10wt%, 15wt%, 20wt%, and 25wt%) on the properties of Fe₃Si-Si₃N₄-Al₂O₃ composites was investigated. The results show that the apparent porosity varies between 10.3% and 17.3%, the bulk density varies from 2.94 g/cm3 and 3.30 g/cm3, and the cold crushing strength ranges from 67 MPa to 93 MPa. Under the experimental conditions, ferrosilicon nitride, whose content decreases substantially, is unstable; part of the ferrosilicon nitride is converted into Fe₂C, whereas the remainder is retained, eventually forming the ferrosilicon alloy. Thermodynamic assessment of the Si₅AlON₇ indicated that the ferrosilicon alloy accelerated the reactions between Si₃N₄ and α-Al₂O₃ fine powder and that Si in the ferrosilicon alloy was nitrided directly, forming β-SiAlON simultaneously. In addition, fused corundum did not react directly with Si₃N₄ because of its low reactivity.     

Phosphate enrichment mechanism in CaO–SiO2–FeO–Fe2O3–P2O5 steelmaking slags with lower binary basicity

The addition of silica to steelmaking slags to decrease the binary basicity can promote phosphate enrichment in quenched slag samples. In this study, we experimentally investigated phosphate enrichment behavior in CaO–SiO₂–FeO–Fe₂O₃–P₂O₅ slags with a P₂O₅ content of 5.00% and the binary basicity B ranging from 1.0 to 2.0, where the (%Fe_tO)/(%CaO) mass percentage ratio was maintained at 0.955. The experimental results are explained by the defined enrichment degree R_C2S-C3P of solid solution 2CaO·SiO₂–3CaO·P₂O₅ (C₂S–C₃P), where R_C2S-C3P is a component of the developed ion and molecule coexistence theory (IMCT)–N_i model for calculating the mass action concentrations N_i of structural units in the slags on the basis of the IMCT. The asymmetrically inverse V-shaped relation between phosphate enrichment and binary basicity B was observed to be correlated in the slags under applied two-stage cooling conditions. The maximum content of P₂O₅ in the C₂S–C₃P solid solution reached approximately 30.0% when the binary basicity B was controlled at 1.3.     

Comparative study on the corrosion behavior of X52, 3Cr,and 13Cr steel in an O2-H2O-CO2 system:products,reaction kinetics,and pitting sensitivity

The corrosion behaviors of X52, 3Cr low-alloy steel, and 13Cr stainless steel were investigated in an O₂-H₂O-CO₂ environment at various temperatures and O₂-CO₂ partial-pressure ratios. The results showed that the corrosion rates of X52, 3Cr, and 13Cr steels increased with increasing temperature. The corrosion rates slowly increased at temperatures less than 100℃ and increased sharply when the temperature exceeded 100℃. In the absence of O₂, X52, 3Cr, and 13Cr exhibited uniform corrosion morphology and FeCO₃ was the main corrosion product. When O₂ was introduced into the system, various forms of Fe₂O₃ appeared on the surface of the samples. The Cr content strongly influenced the corrosion resistance. The 3Cr steel with a low Cr content was more sensitive to pitting than the X52 or 13Cr steel. Thus, pitting occurred on the surface of 3Cr when 1.25 MPa of O₂ was added; this phenomenon is related to the non-uniform distribution of Cr in 3Cr.     

Effect of Fe2O3 on the size and components of spinel crystals in the CaO-SiO2-MgO-Al2O3-Cr2O3 system

size of spinel crystals in the CaO-SiO₂-MgO-Al₂O₃-Cr₂O₃ system was investigated using lab experiments carried out in a carbon tube furnace. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD) were used to analyze the microstructure, components, and the mineral phases of synthetic slags. FactSage 7.1 was used to calculate the crystallization process of the molten slag. The results showed that the addition of Fe₂O₃ promoted the precipitation of spinel crystals and inhibited the formation of dicalcium silicate. The size of spinel crystals increased from 2.74 to 8.10 μm and the contents of chromium and iron in the spinel varied as the Fe₂O₃ addition was increased from 0 to 20wt%. Fe₂O₃ thermodynamically provided the spinel-forming components to enhance the formation of FeCr₂O₄, MgFe₂O₄, and Fe₃O₄. The addition of Fe₂O₃ increased the fraction of liquid phase in a certain temperature range and promoted diffusion by decreasing the slag's viscosity. Therefore, Fe₂O₃ is beneficial to the growth of spinel crystals in stainless steel slag.     

Microwave absorption properties of SiC@SiO_2@Fe_3O_4 hybrids in the 2–18 GHz range

To enhance the microwave absorption performance of silicon carbide nanowires(SiCNWs), SiO_2 nanoshells with a thickness of approximately 2 nm and Fe_3O_4 nanoparticles were grown on the surface of SiCNWs to form SiC@SiO_2@Fe_3O_4 hybrids. The microwave absorption performance of the SiC@SiO_2@Fe_3O_4 hybrids with different thicknesses was investigated in the frequency range from 2 to 18 GHz using a free-space antenna-based system. The results indicate that SiC@SiO_2@Fe_3O_4 hybrids exhibit improved microwave absorption. In particular, in the case of an SiC@SiO_2 to iron(III) acetylacetonate mass ratio of 1:3, the microwave absorption with an absorber of 2-mm thickness exhibited a minimum reflection loss of-39.58 d B at 12.24 GHz. With respect to the enhanced microwave absorption mechanism, the Fe_3O_4 nanoparticles coated on SiC@SiO_2 nanowires are proposed to balance the permeability and permittivity of the materials, contributing to the microwave attenuation.     

Microwave absorption properties of SiC@SiO2@Fe3O4 hybrids in the 2–18 GHz range

To enhance the microwave absorption performance of silicon carbide nanowires (SiCNWs), SiO2 nanoshells with a thickness of approximately 2 nm and Fe3O4 nanoparticles were grown on the surface of SiCNWs to form SiC@SiO2@Fe3O4 hybrids. The microwave absorption performance of the SiC@SiO2@Fe3O4 hybrids with different thicknesses was investigated in the frequency range from 2 to 18 GHz using a free-space antenna-based system. The results indicate that SiC@SiO2@Fe3O4 hybrids exhibit improved microwave absorption. In particular, in the case of an SiC@SiO2 to iron(III) acetylacetonate mass ratio of 1:3,themicrowave absorption with an absorber of 2-mm thickness exhibited a minimum reflection loss of?39.58 dB at 12.24 GHz. With respect to the enhanced microwave absorption mechanism, the Fe3O4 nanoparticles coated on SiC@SiO2 nanowires are proposed to balance the permeability and permittivity of the materials, contributing to the microwave attenuation.     

Synthesis of highly ordered SnO2／Fe2O3 composite nanowire arrays by electrophoretic deposition method

Highly ordered SnO2/Fe2O3 composite nanowire arrays have been synthesized by electrophoretic deposition method. The morphology and chemical composition of SnO2/Fe2O3 composite nanowire arrays are characterized by SEM, TEM, EDX, XPS, and XRD. The results show that the SnO2/Fe2O3 composite nanowires are about 180 nm in width and tens of microns in length, and they are composed of small nanoparticles of tetraganal SnO2 and rhombohedral α-Fe203 with diameters of 10-15nm. The SnO2/Fe2O3 composite nanowires are formed by a series of chemical reactions.     

Analysis of the factors affecting the magnetic characteristics of nano-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> particles

We prepared Fe3O4 nanoparticles using chemical coprecipitation and studied the factors affecting the magnetic characteristics of nano-Fe3O4 particles.We identified four factors and three levels of an orthogonal experiment and investigated these four factors that affect the magnetic characteristics of the Fe3O4 particles.We obtained important information from this investigation.The Fe3+ to Fe2+ molar ratio,the iron precursor salt,the amount of surfactant and the amount of alkali were found to be important.We also studied the influence of the order of alkali and surfactant addition,the aging time and the stirring speed on the magnetic characteristics of the nano-Fe3O4 particles.The Fe3O4 preparation process was also analyzed.     

Rational construction of NiCo_2O_4@Fe_2O_3 core-shell nanowire arrays for high-performance supercapacitors

Fe_2O_3 electrode materials exhibit excellent electrochemical performance in electrochemical energy storage system. However, its poor electrical conductivity limits its future practical application. The binder-free Ni Co_2O_4@Fe_2O_3 composites was reasonably designed and fabricated on carbon fiber paper with NiCo_2 O_4 nanowires as conductive scaffold in the present investigation. The three-dimensional nanostructure of the porous Fe_2O_3 nanorods coated the Ni Co2 O4 nanowire arrays showed the fascinating electrochemical performance, including high specific capacitance of 262 m F/cm2 at a current density of 1 m A/cm2, and remarkable cycle stability with～74.2% capacitance retention after 4000 cycles. The excellent pseudocapacitance performance of NiCo_2O_4@Fe_2O_3 composite materials is due to synergistic effect between NiCo_2O_4 and Fe_2O_3. The results of the present work show that NiCo_2O_4@Fe_2O_3 core-shell composite electrode is expected to exhibit excellent performance in the field of supercapacitors.     

Tailoring impedance match and enhancing microwave absorption of Fe3O4/ Bi24Fe2O39/Bi hollow porous microrods by controlling their composition

A self-assembly/precipitate conversion/decomposition process was developed for the controllable synthesis of Fe_3O_4/Bi_(24)Fe_2O_(39)/Bi hollow porous microrods(HPMRs).The results demonstrated that the crystal size,component,and performances of HPMRs could be effectively modulated via changing Fe~(2+)/Bi~(3+)molar ratio(γ).Fe_3O_4/Bi_(24)Fe_2O_(39)/Bi HPMRs exhibited ferromagnetic behavior at room temperature.As Bi and Bi_(24)Fe_2O_(39)contents increased withγ,the saturation magnetization M_sand attenuation constantly decreased,whereas coercivity H_cand impedance matching ratio increased.Compounding Fe_3O_4with small quantities of Bi and Bi_(24)Fe_2O_(39)into HPMRs can significantly enhance microwave absorption.Fe_3O_4/Bi_(24)Fe_2O_(39)/Bi HPMRs formed atγ=1:0.25 exhibited the optimum microwave absorption performance.The minimum R_Lwas-47.3 dB at8.72 GHz,corresponding to 2.4 mm sample thickness.The absorption band with the reflection loss below-20 dB was up to 14.0 GHz for the absorber with a thickness of 1.4-8.0 mm.The results demonstrate that the introduction of electromagnetic transparent materials(Bi_(24)Fe_2O_(39)or Bi)can improve the microwave absorption performances of Fe_3O_4 composites owing to enhanced impedance matching rather than attenuation constant.     

Structural and electrical properties of HCl-polyaniline-Ag composites synthesized by polymerization using Ag-coated (NH4)2S2O8 powder

Ag nanoparticles were sputter-deposited on ammonium persulfate ((NH₄)₂S₂O₈) powder to obtain (NH₄)₂S₂O₈-Ag powder, which was used to synthesize the HCl-doped polyaniline-Ag (HCl-PANI-Ag) composite via a polymerization procedure. The Ag nanoparticles were dispersed in the HCl-PANI matrix, and their sizes mainly ranged from 3 to 6 nm. The Ag nanoparticles did not affect the structure of emeraldine salt in the composite, and they increased the ordered crystalline regions in the HCl-PANI matrix. The HCl-PANI-Ag composite had a conductivity of (6.8 ±0.1) S/cm, which is about four times larger than that of the HCl-PANI. The charge transport mechanism in the composite is explained by the three-dimensional Mott variable-range hopping (3D-Mott-VRH).