Current Research Progress in Magnesium Borohydride for Hydrogen Storage (A review)

Hydrogen storage in solid-state materials is believed to be a most promising hydrogen-storage technology for high efficiency, low risk and low cost. Mg(BH₄)₂ is regarded as one of most potential materials in hydrogen storage areas in view of its high hydrogen capacities(14.9 wt% and 145–147 kg cm^-3). However, the drawbacks of Mg(BH₄)₂ including high desorption temperatures(about 250°C–580°C), sluggish kinetics, and poor reversibility make it...     

Hydrogen absorption-desorption characteristic of (Ti0.85Zr0.15)1.1Cr1-xMoxMn based alloys with C14 Laves phase

The microstructure and hydrogen absorption-desorption characteristic of (Ti_0.85Zr_0.15)_1.1Cr_1-xMo_xMn (x ?= ?0.05, 0.1, 0.15, 0.2 ?at.%) alloys were investigated. The results showed that the corresponding alloys were determined as a single phase of C14-type Laves structure. With the increase of Mo content, the maximum and reversible hydrogen absorption capacity decreased, the slope factor H_f increased. Among the studied alloys, (Ti_0.85Zr_0.15)_1.1Cr_0.95Mo_0.05Mn had the best overall properties for practical application of hydrogen storage materials. The maximum and reversible hydrogen storage capacity were 1.76 ?wt% and 1.09 ?wt%, the slope factor H_f was 0.51, and its dissociation enthalpy (ΔH_d) and entropy change (ΔS_d) were 23.1 ?kJ ?mol^?1H₂, 93.8J ?K^?1mol^?1H₂ at 303K, respectively. By studying the dissociation pressures of the synthesized metal hydrides, it was found that Mo had a special effect on the dissociation pressure of Ti–Zr–Cr–Mo–Mn alloys. Among the four alloys, (Ti_0.85Zr_0.15)_1.1Cr_0.95Mo_0.05Mn alloy had the largest hydrogen absorption capacity and the fastest hydrogen desorption rate, which can meet the commercialization demand of hydrogen fuel cell hydrogen supply system.     

二维Ti3C2Tx MXene材料的制备与工艺优化

二维（2D）过渡金属碳/氮化物（MXene）材料是当前最受关注的二维材料之一,其中二维碳化钛（Ti₃C₂T_x MXene）材料的研究最为广泛。该材料目前主要通过刻蚀三元碳化物或氮化物（MAX相）后进一步插层得到,因此MAX相材料的纯度和制备工艺条件直接决定了Ti₃C₂T_x MXene材料的物化性质。主要完成了不同Ti₃AlC₂ MAX相材料的筛选,选择氢氟酸（HF）刻蚀,并优化了不同的插层方法,制备了一系列Ti₃C₂T_x MXene材料。通过X射线衍射（XRD）、场发射扫描电镜（FESEM）、透射电子显微镜（TEM）、原子力显微镜（AFM）和X射线光电子能谱（XPS）等表征,确定使用原位锂离子（Li⁺）插层法可有效获得单层Ti₃C₂T_x MXene材料。制备的单层Ti₃C₂T_x MXene材料的表面平整,片径约为150 nm,厚度约为2 nm。同时,创新性地采用涡旋震荡辅助材料分层,极大地缩短了超声时间,提高了单层Ti₃C₂T_x MXene材料的产率（可达70%）,并且可以避免材料氧化,为Ti₃C₂T_x MXene材料未来应用提供了新方法。     

Ameliorating mechanical properties and reducing anisotropy of as-extruded Mg-1.0Sn-0.5Ca alloy via Al addition

Effects of Al addition to a Mg–Sn–Ca ternary alloy on its microstructure and tensile properties after extrusion were studied via extrusion of Mg-1.0 Sn-0.5 Ca-x Al(x = 0, 0.8, 2.4 wt%) sheets and analysis of the extruded materials.The results showed that Al addition not only refined the grain size(from 9.8 ± 0.7 μm to 8.3 ± 0.4 μm and7.6 ± 0.5 μm) but also accelerated the generation of more second phase(from 0.98 to 1.72 and 4.32%). Except for the CaMgSn and Mg₂Ca in Mg-1.0Sn-0.5 Ca a...     

Enhanced hydrogen storage properties of NaBH4–Mg(BH4)2 composites by NdF3 addition

As two important members of complex hydrides,Mg(BH₄)₂ and Na BH₄ have a high gravimetric capacity (14.9 and10.8 wt%,respectively).In this study,the Mg(BH₄)₂ was synthesized by the ion exchange method.Afterwards,the Mg(BH₄)₂ and Na BH₄ composites with different amounts (30,40 and 50 wt%) of NdF₃ were prepared by mechanical milling.Effects of the Nd F₃ on the microstructural evolution and ...     

Corrosion resistance and thermal stability of sputtered Fe44Al34Ti7N15 and Al61Ti11N28 thin films for prospective application in oil and gas industry

Fe-and Al-based thin-film metallic glass coatings (Fe₄₄Al₃₄Ti₇N₁₅ and Al₆₁Ti₁₁N₂₈) were fabricated using magnetron co-sputtering technique, and their corrosion performances compared against wrought 316L stainless steel. The results of GI-XRD and XPS analyses demonstrated amorphous structure and oxide layer formation on the surface of the fabricated thin films, respectively. The potentiodynamic (PD) polarization test in chloride-thiosulfate (NH₄Cl ​+ ​Na₂S₂O₃) solution revealed lower corrosion current (I_corr) (0.42 ​± ​0.02 ​μA/cm² and 0.086 ​± ​0.001 ​μA/cm² Vs. 0.76 ​± ​0.05 ​μA/cm²), lower passivation current (I_pass) (1.45 ​± ​0.03 ​μA/cm² and 1.83 ​± ​0.07 ​μA/cm² Vs. 1.98 ​± ​0.04 ​μA/cm²), and approximately six-fold higher breakdown potential (E_bd) for Fe- and Al-based coatings than those of wrought 316L stainless steel. Electrochemical Impedance Spectroscopy (EIS) of both films showed 4- and 2-fold higher charge transfer resistance (R_ct), 7- and 2.5-times higher film resistance (R_f), lower film capacitance values (Q_f) (10 ​± ​2.4 ​μS-s^acm^-2, and 5.41 ​± ​0.8 ​μS-s^acm^-2 Vs. 18 ​± ​2.21 ​μS-s^acm^-2), and lower double-layer capacitance values (Q_dl) (31.33 ​± ​4.74 ​μS-s^acm^-2, and 15.3 ​± ​0.48 ​μS-s^acm^-2 Vs. 43 ​± ​4.23 ​μS-s^acm^-2), indicating higher corrosion resistance of the thin films. Cyclic Voltammetry (CV) scan exhibited that the passive films formed on the Fe- and Al-based coatings were more stable and less prone to pitting corrosion than the wrought 316L stainless steel. The surface morphology of both films via SEM endorsed the CV scan results, showing better resistance to pitting corrosion. Furthermore, the thermal analysis via TGA and DSC revealed the excellent thermal stability of the thin films over a wide temperature range typically observed in oil-gas industries.     

Synthesis of amorphous SeP2/C composite by plasma assisted ball milling for high-performance anode materials of lithium and sodium-ion batteries

To promote substantially the performances of red phosphorous(P) anode for lithium and sodium-ion batteries, a simple plasma assisted milling(P-milling) method was used to in-situ synthesize SeP₂/C composite. The results showed that the amorphous SeP₂/C composite exhibits the excellent lithium and sodium storage performances duo to the small nano-granules size and complete combination of selenium(Se) and phosphorous(P) to generate Se–P alloy phase. It was observed that insid...     

Towards understanding the influence of Mg content on phase transformations in the La3-xMgxNi9 alloys by in-situ neutron powder diffraction study

The present work is focused on the studies of the phase-structural transformations in the La_3-xMg_xNi₉ (x = 1.0, 1.1 and 1.2) alloys as active materials of negative electrodes in the Nickel-Metal Hydride(Ni/MH) batteries. The phase equilibria and phase-structural transformations in the alloys were probed by in situ neutron powder diffraction(NPD) at the temperatures ranging from 300 K to 1273 K using the measurements of the equilibrated alloys at 8 setpoint temper...     

Microstructure and electrical conductivity of 10% Yb-doped SrCeO3 ceramics

As a candidate material for hydrogen separation, Yb-doped SrCeO₃ has attracted increasing attention in recent decades. In the present study, Yb-doped SrCe_0.9Yb_0.1O_3-α ceramics were prepared by the dry pressing and sintering approach, with the microstructure evolution and the micro morphology investigated. It was indicated that the ceramics sintered in air were of a pure perovskite structure, and that the sintering temperature had a significant effect on the growth of ceramic grains. The average grain size increased from 1 ​μm to 10 ​μm with an increase in sintering temperature from 1300 to 1500 ​°C. Further investigation of the thermodynamics and kinetics of grain growth revealed that the grain boundary diffusion was the main driving force of grain growth during solid phase sintering, with a grain growth index of 4 and an activation energy of approximately 61.23 ​kJ ​mol⁻¹. These results illustrate an obvious tendency of grain size growth. By electrochemical workstation with different atmospheres the effects of sintering temperature on the conductivity were characterized in the temperature range of 700–900 ​°C. The electrical conductivities σ of SrCe_0.9Yb_0.1O_3-α ceramics in different atmospheres were as follows: σ(wet hydrogen) ​> ​σ(dry hydrogen) ​> ​σ(dry air) ​> ​σ(wet air). In the test atmosphere containing water and hydrogen the conductivity of protons increased with increasing temperature because of the protons jump between lattices in the form of interstitial hydrogen ions or bare protons.     

Hydrogen absorption-desorption cycle decay mechanism of palladium nanoparticle decorated nitrogen doped graphene

As a hydrogen storage material, palladium nanoparticle decorated nitrogen doped graphene (Pd/N-rGO) has drawn much attention owing to its high absorption capacity at moderate conditions. However, its hydrogen absorption-desorption cycle performance, which is essential for their practical application, has been rarely studied. In this paper, a simple and convenient high temperature thermal reduction method was used to synthesize nitrogen-doped graphene decorated with Pd nanoparticles (Pd/N-rGO). Taken it as a representative, the hydrogen absorption-desorption cycle performance of Pd/N-rGO was investigated. The results showed that after three cycles the hydrogen storage capacity dropped from 2.9 ​wt% to 0.8 ​wt% at 25 ​°C and 4 ​MPa pressure. It was found that the palladium nanoparticles shed from Pd/N-RGO sheet after cycle performance test, and then agglomerated. These phenomena will weaken the hydrogen spillover effect, leading to the decrease of hydrogen storage capacity. Meanwhile, decreased defects reduce the hydrogen absorption sites, which will thus deteriorate the hydrogen storage capacity.     

Hydrogen storage performance of LaNi3.95Al0.75Co0.3 alloy with different preparation methods

Rare-earth AB₅-type La–Ni–Al hydrogen storage alloys are widely studied due to their extensive application potentials in hydrogen isotope storage, hydrogen isotope isolation and hydrogen compressors, etc. Good hydriding/dehydriding kinetics, easily activation, high reversibility are important factors for their practical application. However, their overall hydrogen storage performance, especially plateau pressure and hydrogen absorption/desorption durability need to be further optimized. In this study, the microstructures and the hydrogen storage properties of as-cast, annealed, and melt-spun LaNi_3.95Al_0.75Co_0.3 alloys were investigated. The experimental results of XRD and SEM showed that all alloys contained a pure CaCu₅ type hexagonal structure LaNi₄Al phase. The cell volume increased in an order of annealed ?> ?melt-spun ?> ?as-cast, resulting in a lower hydrogen absorption/desorption plateau pressure and a more stable hydride phase. The hydrogen storage capacity of three alloys was almost the same. The slope factor of the annealed and melt-spun alloys is smaller than the as-cast alloy, indicating that heat-treatment process can make the alloys more uniform. For the cycle stability of the alloys, the hydrogen absorption rate of the annealed alloy and melt-spun alloy was much faster than that of the as-cast alloy after 500 cycles. The melt-spun alloy showed high pulverization resistance during hydrogen absorption/desorption, and exhibited an excellent cycling retention of 99% after 500 cycles, suggesting that melt-spinning process can enhance the cycle stability and improve the cycle life of the alloy.     

Spectroscopic properties of Er3+/Ho3+/Tm3+ doped α-SiAlON ceramics under 793 ​nm excitation

This paper reports the first demonstration of super broadband infrared downshifting emission extending from 1640 ​nm to 2200 ​nm with the full width at half maximum of ∼ 417 ​nm in lanthanides (Er³⁺, Ho³⁺, and Tm³⁺)-doped α-SiAlON ceramics upon 793 ​nm excitation. Using α-Si₃N₄ ceramic as a precursor the lanthanides-doped α-SiAlON ceramics were synthesized by the hot-press method. The lanthanides induced no significant secondary phases in the sintered α-SiAlON ceramics. Strong two-photon upconversion emission bands centered at 547, 671 and 694 ​nm have also been observed upon 793 ​nm excitation. The time-resolved measurements of the upconversion emissions confirm that the efficient energy transfer among the Er³⁺, Ho³⁺ and Tm³⁺ ions as well as the ground state absorption in Er³⁺ and Tm³⁺ are responsible for the observed spectroscopic properties.     

Effects of heat treatment on microstructure and mechanical properties of SLMed Sc-modified AlSi10Mg alloy

The influence of heat treatments on the microstructures and mechanical properties of the selective laser melting manufactured AlSi10Mg alloy modified with Sc was systematically investigated. The results showed that the addition of Sc element introduced primary Al₃ Sc, which increased the heterogeneous nucleation during the solidification of AlSi10Mg alloy, and then the ultrafine network eutectic structure was obtained, and hence the tensile strength was improved significantly(nearly 2...     

Nickel-introduced structurally ordered PtCuNi/C as high performance electrocatalyst for oxygen reduction reaction

Designing highly active and durable oxygen reduction reaction (ORR) electrocatalysts is essential for developing efficient proton-exchange membrane fuel cells (PEMFCs). In this work, ordered PtCuNi/C nanoparticles (NPs) were synthesized using an impregnation reduction method. This study shows that the incorporation of Ni in ordered PtCu/C can effectively adjust the electronic structure of Pt, thereby optimizing oxygen binding energy for the ORR. The obtained intermetallic ordered PtCuNi/C NPs significantly improved ORR activity and durability compared to ordered PtCu/C. Specifically, PtCu_0·5Ni_0·5/C-700 shows a mass activity of 1.29 ​A ​mg _Pt⁻¹ ​at 0.9 ​V vs. reversible hydrogen electrode (RHE), which is about 9.2 times higher than that of commercial Pt/C. PtCu_0.5Ni_0.5/C-700 is also shown to be competent cathode catalyst for a single-cell system exhibiting high power density (461 ​mW ​cm⁻²). This work demonstrates that ordered PtCu_0·5Ni_0·5/C-700 can be used as a highly active and durable ORR catalyst in PEMFCs.     

Catalytic effect of a novel MgC_(0.5)Co_3 compound on the dehydrogenation of MgH_2

The application of magnesium hydride(MgH₂) is limited due to the high reaction temperature and slow kinetics during dehydrogenation. In order to ameliorate the dehydrogenation property of MgH₂, MgC_0.5Co₃ compound with induction and catalytic effects was introduced into the Mg/MgH₂ system via ball-milling and hydriding combustion methods in present study. Compared to the pure MgH₂,the initial hydrogen desorption temperature of MgH<...     

Large specific surface area S-doped Fe–N–C electrocatalysts derived from Metal–Organic frameworks for oxygen reduction reaction

It is highly desired but challenging to develop platinum group metal-free electrocatalysts for oxygen reduction reaction (ORR), which can promote the commercialization of fuel cell technology. To achieve this target, we report a one-step doping method to prepare S-doped Fe–N–C catalysts using zeolite imidazole framework (ZIF-8) and iron (III) thiocyanate (Fe(SCN)₃) as precursor. Different from conventional doping approach, i.e. physical mixing, Fe(SCN)₃ is in-situ added during ZIF-8 formation which would encapsulate Fe(SCN)₃ molecules inside ZIF-8 to avoid structure destruction and create potential replacement of Zn ions by Fe ions to form uniform Fe–N₄ complexes. As a result, the prepared S-doped Fe–N–C catalysts own large specific surface areas with a maximum value of 1326 ​m² ​g⁻¹ and a dual-scale porous structure that benefits mass transport. Significantly, the composition-optimized catalyst exhibits superior ORR activity in both 0.1 ​M HClO₄ electrolyte and 0.1 ​M KOH electrolyte, in which the half-wave potential reaches 0.81 ​V and 0.92 ​V (vs. RHE), respectively. Remarkable stability is also attained, which loses 2 ​mV only after 10000 potential cycles in O₂-saturated 0.1 ​M HClO₄ and remains almost constant in O₂-saturated 0.1 ​M KOH, surpassing commercial Pt/C catalyst in both acidic and alkaline medium.     

镁基储氢材料的研究进展

从镁基储氢材料体系入手,综述了该体系的研究情况及近期进展．对镁基储氢材料进行了合理的分类,将其分为单质镁储氢材料、镁基储氢合金和镁基储氢复合材料．并结合各类镁基储氢材料的国内外研究状况,指出要改善镁基储氢材料的储氢性能,必须走多元合金化的路线并在学习有关理论的基础上,采用优化合金成分与新的合成方法来进一步提高材料的储氢性能．     

Magnetic field induced synthesis of (Ni,Zn)Fe2O4 spinel nanorod for enhanced alkaline hydrogen evolution reaction

Recently, the introduction of external fields(light, thermal, magnetism, etc.) during electrocatalysis reactions gradually becomes a new strategy to modulate the catalytic activities. In this work, an external magnetic field was innovatively employed for the synthesis progress of(Ni, Zn)Fe₂O₄spinel oxide(M-(Ni, Zn)Fe₂O₄). Results indicated the magnetic field(≤250 m T) would affect the morphology of catalyst due to the existing Fe ions, inducing the M-(...     

Thermal damage and ablation behavior of plasma sprayed Ba2SmTaO6 coatings irradiated by high power continuous laser

Ba₂SmTaO₆ laser protection coatings of ≈200 μm thickness were deposited onto stainless steel surfaces by air plasma spraying, and the laser irradiation resistance of the coatings was investigated. For laser irradiation with a laser power density less than 1000 W/cm², the coatings kept intact. For a laser power density exceeding 1500 W/cm², the Ba₂SmTaO₆ coatings underwent recrystallization, grain growth occurred, and certain spray...     

Linear and non-linear pseudocapacitances with or without diffusion control

Pseudocapacitance is an important reversible charge storage mechanism in many electrode materials. Although the concept was first proposed in early 1960s, it has been more widely studied following the observation of rectangular cyclic voltammograms(CVs) when testing some transition metal oxides and electronically conducting polymers, and the association with supercapacitor. However, interpretation of pseudocapacitance is inconsistent in the literature. Although all agree that materials are pseud...