Effect of Nb on the corrosion behavior of continuous bulk metallic glass-coated steel wire composites

(Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5)_100?xNb_x (at%, x=0 and 8) bulk metallic glasses (BMGs) were coated on the surface of Q195 steel wires by a continuous coating process. The potentiodynamic polarization tests of these BMGs were conducted in 3.5wt% NaCl aqueous solution. It is found that the addition of 8at% Nb into Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 alloy results in the improvement of corrosion resistance with the pitting potential of ?52 mV, the open circuit potential of ?446 mV, and the corrosion current density of 9.86×10?6 mA/cm2. This may be attributed to that Nb is beneficial to passivate and stabilize Zr and Ti.     

Effect of TRT process on GFA, mechanical properties and microstructure of Zr-based bulk metallic glass

The effect of yttrium addition on the glass-forming ability(GFA) and mechanical properties of the Zr-based (Zr_(0.525)Al_(0.1)Ti_(0.05)Cu_(0.179)Ni_(0.146))_(100-x)Y_x and(Zr_(0.55)Al_(0.15)Ni_(0.1)Cu_(0.2))_(100-x)Y_x(x=0,0.2,0.4 0.6,1,2) alloys was studied.Micro-alloying of 0.6%yttrium enhances the room temperature ductility as well as the GFA of the Zr-based alloys.The mechanism of enhancing the GFA and room temperature ductility was analyzed.It is indicated that proper yttrium addition stabilizes the...     

Centimeter-sized Ti-based bulk metallic glass with high specific strength

Based on the quaternary Ti₄₁Zr₂₅Be₂₉Al₅ glassy alloy with a critical diameter of 7 mm reported not long ago, an obvious enhancement of glass-forming ability (GFA) has been realized in this alloy by the addition of Cu element. A series of (Ti₄₁Zr₂₅Be₂₉Al₅)_100?xCu_x (x=0, 2, 5, 7, 9, 11 at%) glassy alloys have been developed and some of them can be cast into one-centimeter diameter fully glassy rods by copper mold suction casting. It has been found that Cu addition could stabilize the liquid phase and suppress the crystallization, resulting in improvement of the GFA of the alloy. The addition of Cu also increases the compressive strength of the alloy and the (Ti₄₁Zr₂₅Be₂₉Al₅)₉₁Cu₉ glassy alloy possesses a specific strength (defined as yield strength/density) of 4.13×10⁵ Nm/kg, which is much higher than most other reported centimeter-sized bulk metallic glasses. The present result suggests that the newly developed (Ti₄₁Zr₂₅Be₂₉Al₅)₉₁Cu₉ glassy alloy is a good candidate for structural applications because of its good glass-forming ability and mechanical properties.     

Glass-forming ability,microhardness, corrosion resistance,and dealloying treatment of Mg60-xCu40Ndx alloy ribbons

The influence of Nd addition on the glass-forming ability (GFA), microhardness, and corrosion resistance of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25, at%) alloys were investigated by differential scanning calorimetry, Vickers-type hardness tests, and electrochemical methods. The results suggest that the GFA and microhardness of the amorphous alloys increase until the Nd content reaches 20at%. The corrosion potential and corrosion current density obtained from the Tafel curves indicate that the Mg₃₅Cu₄₀Nd₂₅ ternary alloy exhibits the best corrosion resistance among the investigated alloys. Notably, nanoporous copper (NPC) was synthesized through a single-step dealloying of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25) ternary alloys in 0.04 mol·L-1 H₂SO₄ solution under free corrosion conditions. The influence of dealloying process parameters, such as dealloying time and temperature, on the microstructure of the ribbons was also studied using the surface diffusivity theory. The formation mechanism of dealloyed samples with a multilayered structure was also discussed.     

Microstructure, crystalline phase and electrical properties of Li0.06(Na0.5K0.5)0.94Nb(1−2x/5)Mg x O3 lead-free piezoelectric ceramics

MgO-modified Li_0.06(Na_0.5K_0.5)_0.94NbO₃ (L₆NKN) lead-free piezoelectric ceramics were synthesized by normal sintering at a relatively low temperature of 1000°C. The crystalline phase, microstructure, and electrical properties of the ceramics were investigated with a special emphasis on the influence of MgO content. The addition of MgO effectively improves the sinterability of the L₆NKN ceramics. X-ray diffraction analysis indicates that the morphotropic phase boundary (MPB) separating orthorhombic and tetragonal phases for the ceramics lies in the range of Mg doping content (x) from 0.3at% to 0.7at%. High electrical properties of the piezoelectric constant (d ₃₃=238 pC/N), planar electromechanical coupling coefficient (k _p=41.5%), relative dielectric constant (? _r=905), and remanent polarization (P _r=38.3 μC/cm²) are obtained from the specimen with x=0.5at%, which suggests that the Li_0.06(Na_0.5K_0.5)_0.94Nb_(1?2x/5)Mg _x O₃ (x=0.5at%) ceramic is a promising lead-free piezoelectric material.     

Effects of Cr and Mo elements on the microstructures and compressive properties of the in situ (TiC_xN_y–TiB_2)/Ni cermets

In-situ(TiC_xN_y–TiB_2)/Ni cermets with 70 wt%TiC_xN_y–TiB_2 were successfully fabricated by combustion synthesis and hot pressing sintering in Ni-Ti-B_4C-BN powder systems.The microstructures,density,compressive properties,and hardness of the TiC_xN_y–TiB_2/Ni cermets with the addition of 0–8 wt%Cr/Mo to the Ni-Ti-B_4C-BN powder systems were compared and analysed.The results showed that the ceramic particles distributed uniformly in the cermets,and the size of the ceramic particles reduced with the Cr/Mo addition.Both Cr and Mo addition can improve the hardness,compressive properties,and fracture strains of the cermets.The hardness,compressive strength,and fracture strain of the(TiC_xN_y–TiB_2)/(Ni+Cr)cermets increased from 1561 HV,2.94 GPa,and 2.9%to 1864 HV,3.65 GPa,and 3.4%,respectively when the Cr content increased to 5 wt%.The hardness and compressive strength of the(TiC_xN_y–TiB_2)/(Ni+Mo)cermets increased from 1561 HV and 2.94 GPa to 1902 HV and 3.43 GPa,respectively when the Mo content increased to 8 wt%.The cermets with Cr had better compressive properties than the cermets with Mo.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

Influence of yttrium on the structure and magnetostriction of Fe83Ga17 alloy

Polycrystalline Fe₈₃Ga₁₇ alloy rods with various amounts of yttrium were prepared by high vacuum induction melting. It is found that yttrium addition has a significant effect on the structure and magnetostriction of Fe₈₃Ga₁₇ alloy. The small addition of yttrium alters the solidification character and the grain shape of Fe₈₃Ga₁₇ alloy, and as a result, columnar grains with the ??100?? preferential direction are produced. Yttrium addition improves the magnetostrictive performance of the as-cast Fe₈₃Ga₁₇ alloy. The magnetostriction values of the as-cast alloy with 0.32at% and 0.64at% yttrium addition go up to 119×10^?6 and 137×10^?6 under 15 MPa compressive stress, respectively. The energy dispersive spectroscopy (EDS) result shows that almost all of the yttrium atoms exist in the Y₂Fe_17?x Ga _x phase. A small amount of this kind of secondary phase cannot obviously increase the saturate magnetic field.     

Effects of yttrium on the formation and magnetic properties of bulk metallic glassy (Fe,Co)-B-Si-Nb alloys

The bulk metallic glassy (BMG) rods of [(Fe_0.5Co_0.5)_0.72B_0.192Si_0.048Nb_0.04]_100-xY_x (x=0-6) and [(Fe_xCo_1-x)_0.72B_0.192Si_0.048Nb_0.04]₉₆Y₄ (x=0.5-0.8) were prepared by copper mold casting. The structure, thermal stability, and magnetic properties of the samples were studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and vibrating sample magnetometer (VSM). Adding 1at% to 6at% of yttrium, the bulk glassy alloy rods of [(Fe_0.5Co_0.5)_0.72B_0.192Si_0.048Nb_0.04]_100-xY_x(x=0-6) with the diameter of 3 mm were not formed, and the sample with 4at% of yttrium showed less crystalline phase than others. When the Fe/Co atomic ratio was between 5:5 and 7:3, the bulk glassy alloy rods of [(Fe_1-xCo_x)_0.72B_0.192Si_0.048Nb_0.04]₉₆Y₄ (x=0.5-0.8) with the diameter of 2 mm were fabricated. In the (Fe, Co)-B-Si-Nb-Y BMGs, when the Fe content increased, the thermal stability, the supercooled liquid region, and the glass-forming ability (GFA) decreased, but the saturation magnetization (M_s) increased.     

Formation and mechanical properties of Zr-based bulk metallic glass composites with high oxygen levels

Zr-based bulk metallic glass(BMG) composites with in situ formed Y 2 O 3 particle reinforcements were synthesized by proper additions of Y to ultrahigh-oxygen-containing glass-forming alloy precursors.Microstructures,thermal stabilities,and mechanical properties of the composites were investigated.Glass formation was greatly enhanced by Y additions in the alloys and the resultant particles were homogenously distributed in the glassy matrix,allowing for the fabrication of oxide dispersion strengthened BMG composites.The compressive strength and hardness increased by 10% and 20%,respectively,with the introduction of Y 2 O 3 particles.These results are significant for the design and production of Zr-based BMGs and BMG composites with improved properties using commercial high-oxygen content raw materials under industrial conditions.     

Correlation between the glass-forming ability and activation energy of crystallization for Zr75−x Ni25Al x metallic glasses

The thermal stability and the kinetics of glass transition and crystallization for Zr_75?x Ni₂₅Al _x (x = 8–15) metallic glasses were investigated using differential scanning calorimetry (DSC) under continuous heating conditions. The apparent activation energy of glass transition rises monotonously with the Al content increasing; the activation energy of crystallization increases with Al changing from 8at% to 15at%, and then decreases with Al further up to 24at%, which exhibits a good correlation to the thermal stability and the glass-forming ability (GFA). The Zr₆₀Ni₂₅Al₁₅ metallic glass with the largest supercooled liquid region and GFA possesses the highest activation energy of crystallization. The relation between the thermal stability, GFA and activation energy of crystallization was discussed in terms of the primary precipitated phases.     

玻璃粉对混凝土酸侵蚀性能的影响

采用试验方法,研究了玻璃粉替代胶凝材料在不同掺量(0、5%、8%、15%)时对混凝土抗压强度和耐酸侵蚀性的影响。对比了各个试样在5%H2SO4溶液和5%CH3COOH溶液中腐蚀28 d后的质量亏损和抗压强度损失,并采用SEM分析了试样腐蚀后的表面形貌。结果表明,玻璃粉有利于提高混凝土的耐H2SO4和CH3COOH侵蚀性,耐CH3COOH侵蚀差于耐H2SO4腐蚀,H2SO4侵蚀后的试样表面形成了大量石膏,CH3COOH侵蚀后试样表面疏松并出现了大量孔洞和裂纹。当玻璃粉掺量为8%时,试样的耐H2SO4和CH3COOH侵蚀性最佳。     

Microstructure and improved mechanical properties of ultrafine-grained Mo-12Si-8.5B (at.%) alloys with addition of ZrB2

Multi-hierarchical Mo-12Si-8.5B-x Zr B_2(x=0,0.5,1.0,1.5,2.5 wt%)alloys consisting of three ultrafine-grained(UFG,0.47–0.81μm)phases of Mo_5Si B_2(T2),Mo_3Si and Mo solid solution(α-Mo)were prepared by mechanical alloying following hot pressing.Microstructure observations showed that the intermetallic phases(Mo_3Si and T2)distributed dispersedly in the continuousα-Mo matrix associated with the homogeneously embedded nanoscaled particles(10–225 nm)in the grain interiors and at the grain boundaries.The Mo-12Si-8.5B-x Zr B_2alloys exhibited monotonically increasing compressive strength to 3.13 GPa with increasing content of Zr B_2,and the fracture toughness increased about 27%and reached at 11.5 MPa m~(1/2)at 1.0 wt%Zr B_2,rendering the Mo-12Si-8.5B-1.0 wt%Zr B_2alloy possessing the best combined mechanical properties of high strength and high toughness.The underlying reason for the superior mechanical properties of the Mo-12Si-8.5B-x Zr B_2alloys is that the dispersedly distributed nanosized particles in the UFG multi-phased-matrix can not only effectively block the dislocation motion to increase the strength but also store the dislocations to increase the strain hardening ability during mechanical deformation.     

Interfacial intermetallic compound growth and shear strength of low-silver SnAgCuBiNi/Cu lead-free solder joints

The growth rule of the interfacial intermetallic compound (IMC) and the degradation of shear strength of Sn-0.8Ag-0.5Cu-2.0Bi-0.05Ni (SACBN)/Cu solder joints were investigated in comparison with Sn-3.0Ag-0.5Cu (SAC305)/Cu solder joints aging at 373, 403, and 438 K. The results show that (Cu_1?x,Ni_x)₆Sn₅ phase forms between the SACBN solder and Cu substrate during soldering. The interfacial IMC thickens constantly with the aging time increasing, and the higher the aging temperature, the faster the IMC layer grows. Compared with the SAC305/Cu couple, the SACBN/Cu couple exhibits a lower layer growth coefficient. The activation energies of IMC growth for SACBN/Cu and SAC305/Cu couples are 111.70 and 82.35 kJ/mol, respectively. In general, the shear strength of aged solder joints declines continuously. However, SACBN/Cu solder joints exhibit a better shear strength than SAC305/Cu solder joints.     

Effects of phosphorus addition on the properties of Sn-9Zn lead-free solder alloy

This article explores the effects of phosphorus addition on the wettability between Sn-9Zn solder alloy and Cu substrates, the oxidation behavior and the corrosion behavior of Sn-9Zn solder alloy. Spreading test was used to characterize the wettability of Sn-9Zn-xP solder alloys to Cu substrates. The oxidation and corrosion behaviors of Sn-9Zn-xP solder alloys were determined by means of weight gaining, and secondary ion mass spectrometry was used to analyze the oxygen content. The role and mechanism of P in the solder alloys were also discussed. It is found that the addition of P can significantly improve the wettability of the solder alloys. Incorporating P into Sn-9Zn solder alloy obviously decreases the oxygen content and enhances the oxidation and corrosion resistance. Microstructure observations show that an appropriate amount of P can greatly refine coarse rod-like Zn-rich phases in Sn-9Zn solder alloy.     

Effect of Mo on properties of the industrial Fe-B-alloy-derived Fe-based bulk metallic glasses

The experimental results concerning the effects of Mo on the glass-forming ability (GFA), thermal stability, and mechanical, anticorrosion, and magnetic properties of an (Fe71.2B24Y4.8)96Nb4 bulk metallic glass (BMG) were presented. An industrial Fe-B alloy was used as the raw material, and a series of Fe-based BMGs were synthesized. In BMGs with the Mo contents of approximately 1at%-2at%, the cast alloy reached a critical diameter of 6 mm. The hardness and fracture strength also reached their maximum values in this alloy system. However, the anticorrosion and magnetic properties of the BMGs were not substantially improved by the addition of Mo. The low cost, good GFA, high hardness, and high fracture strength of the Fe-based BMGs developed in this work suggest that they are potential candidates for commercial applications.     

B对Zr-Ti-Ni-Cu-Be块状非晶合金热稳定性的影响

利用X射线衍射(XRD)及差热分析(DSC)等方法研究了添加B对Zr Ti Cu Ni Be块状非晶合金的形成、结晶及热稳定性的影响·结果表明:在Zr Ti Cu Ni Be合金系中添加B可明显改变该合金的玻璃转变温度Tg,一次结晶温度Tx及过冷液相区ΔT等参数·当y(B)≤3%时,B的添加可使合金保持块状非晶,提高Tg、Tx并扩大过冷液相区,使非晶热稳定性增加;当y(B)≥6%时,B的添加将诱导大量的粗大Zr2Cu及ZrB2等晶体的析出·由于它们非纳米晶,尺寸较大,形状不规整,不能作为非晶复合材料的增强体·     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Preparation and thermal stability of Pd<Subscript>40.5</Subscript>Ni<Subscript>40.5</Subscript>Si<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>P<Subscript>19−<Emphasis Type="Italic">x</Emphasis></Subscript> bulk metallic glasses

With the addition of Si to replace some P, Pd_40.5Ni_40.5Si _x P_19−x (x=0, 2.5, 5, 9.5, 14, and 19 in atomic number fraction) bulk glassy samples with the diameter of about 5 mm were successfully prepared by use of flux treatment and water quenching technology. With the increase of Si content, the glass forming ability of Pd_40.5Ni_40.5Si _x P_19−x increases first for low Si content and then decreases for high Si content (Si≥9.5at%). The Pd_40.5Ni_40.5Si ₅ P₁₄ glassy alloy possesses the largest supercooled liquid region ΔT of 119 K, the largest reduced glass transition temperature of 0.621, and the largest γ parameter of 0.460, indicating that this glassy alloy possesses very large glass forming ability and very high thermal stability.     

Effect of indium addition on the microstructural formation and soldered interfaces of Sn-2.5Bi-1Zn-0.3Ag lead-free solder

The microstructural formation and properties of Sn-2.5Bi-xIn-1Zn-0.3Ag (in wt%) alloys and the evolution of soldered interfaces on a Cu substrate were investigated. Apart from the relatively low melting point (about 195℃), which is close to that of conventional eutectic Sn-Pb solder, the investigated solder presents superior wettability, solderability, and ductility. The refined equiaxial grains enhance the mechanical properties, and the embedded bulk intermetallic compounds (IMCs) (Cu₆Sn₅ and Cu₅Zn₈) and granular Bi particles improve the joint reliability. The addition of In reduces the solubility of Zn in the β-Sn matrix and strongly influences the separation and growth behaviors of the IMCs. The soldered interface of Sn-2.5Bi-xIn-1Zn-0.3Ag/Cu consists of Cu-Zn and Cu-Sn IMC layers.