Effect of slag composition on the cleanliness of 28MnCr5 gear steel in the refining processes

The equilibrium reaction between CaO—Al₂O₃—SiO₂—MgO slag and 28MnCr5 molten steel was calculated to obtain the suitable slag composition which is effective for decreasing the oxygen content in molten steel. The dissolved oxygen content [O] in molten steel under different top slag conditions was calculated using a thermodynamic model and was measured using an electromotive force method in slag–steel equilibrium experiments at 1873 K. The relations among [O], the total oxygen content (T.O), and the composition of the slag were investigated. The experimental results show that both [O] and T.O decrease with decreasing SiO₂ content of the slag and exhibit different trends with the changes in the CaO/Al₂O₃ mass ratio of the slag. Increasing the CaO/Al₂O₃ mass ratio results in a decrease in [O] and an increase in T.O. To ensure that T.O ≤ 20 ppm and [O] ≤ 10 ppm, the SiO₂ content should be controlled to <5wt%, and the CaO/Al₂O₃ mass ratio should be in the range from 1.2 to 1.6.     

Microstructure of Ni–Al powder and Ni–Al composite coatings prepared by twin-wire arc spraying

Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni₃Al, Al₂O₃, and NiO. The Ni–Al phase and a small amount of Al₂O₃ particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al₂O₃. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni₃Al in addition to a small amount of Al and Al₂O₃, and NiAl and Ni₃Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl₃ precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.     

Effect of Fe2O3 on the size and components of spinel crystals in the CaO-SiO2-MgO-Al2O3-Cr2O3 system

size of spinel crystals in the CaO-SiO₂-MgO-Al₂O₃-Cr₂O₃ system was investigated using lab experiments carried out in a carbon tube furnace. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD) were used to analyze the microstructure, components, and the mineral phases of synthetic slags. FactSage 7.1 was used to calculate the crystallization process of the molten slag. The results showed that the addition of Fe₂O₃ promoted the precipitation of spinel crystals and inhibited the formation of dicalcium silicate. The size of spinel crystals increased from 2.74 to 8.10 μm and the contents of chromium and iron in the spinel varied as the Fe₂O₃ addition was increased from 0 to 20wt%. Fe₂O₃ thermodynamically provided the spinel-forming components to enhance the formation of FeCr₂O₄, MgFe₂O₄, and Fe₃O₄. The addition of Fe₂O₃ increased the fraction of liquid phase in a certain temperature range and promoted diffusion by decreasing the slag's viscosity. Therefore, Fe₂O₃ is beneficial to the growth of spinel crystals in stainless steel slag.     

Primary beneficiation of tantalite using magnetic separation and acid leaching

Primary beneficiation was successfully performed prior to dissolution of manganotantalite (sample A) and ferrotantalite (sample C) samples obtained from two different mines in the Naquissupa area, Mozambique. Magnetic separation removed the majority of iron and titanium, whereas H₂SO₄ leaching removed a large portion of thorium and uranium in these samples. Analytical results indicated that 64.14wt% and 72.04wt% of the total Fe and Ti, respectively, and ~2wt% each of Nb₂O₅ and Ta₂O₅ were removed from sample C (ferrotantalite) using the magnetic separation method, whereas only 9.64wt% and 8.66wt% of total Fe₂O₃ and TiO₂, respectively, and ~2wt% each of Nb₂O₅ and Ta₂O₅ were removed from sample A (manganotantalite). A temperature of 50°C and a leaching time of 3 h in the presence of concentrated H₂SO₄ were observed to be the most appropriate leaching conditions for removal of radioactive elements from the tantalite ores. The results obtained for sample A under these conditions indicated that 64.14wt% U₃O₈ and 60.77wt% ThO₂ were leached into the acidic solution, along with 4.45wt% and 0.99wt% of Nb₂O₅ and Ta₂O₅, respectively.     

AISI 321不锈钢钢钢包精炼过程中钙含量对夹杂物的影响

The effect of three heat processes with different calcium contents on the evolution of inclusions during the ladle furnace refining process of AISI 321 stainless steel was investigated. The size, morphology, and composition of the inclusions were analyzed by scanning electron microscopy and energy-dispersive X-ray spectroscopy. After the addition of aluminum and titanium, the primary oxide in the AISI 321 stainless steel was an Al₂O₃–MgO–TiO_x complex oxide, in which the mass ratio of Al₂O₃/MgO was highly consistent with spinel (MgO·Al₂O₃). After calcium treatment, the calcium content in the oxide increased significantly. Thermodynamic calculations show that when the Ti content was 0.2wt%, the Al and Ca contents were less than 0.10wt% and 0.0005wt%, respectively, which was beneficial for the formation of liquid inclusions in molten steel. Moreover, the modification mechanism of calcium on TiN-wrapped oxides in combination with temperature changes was discussed.     

Electrical conductivity of molten LiF-DyF3-Dy2O3-Cu2O system for Dy-Cu intermediate alloy production

Dy-Cu intermediate alloys have shown substantial potential in the field of magnetostrictive and magnetic refrigerant materials. Therefore, this study focused on investigating the electrical conductivity of molten-salt systems for the preparation of Dy-Cu alloys and on optimizing the corresponding operating parameters. The electrical conductivity of molten LiF-DyF₃-Dy₂O₃-Cu₂O systems was measured from 910 to 1030℃ using the continuously varying cell constant method. The dependencies of the LiF-DyF₃-Dy₂O₃-Cu₂O system conductivity on the melt composition and temperature were examined herein. The optimal operating conditions for Dy-Cu alloy production were determined via analyses of the electrical conductivity and activation energies for conductance, which were calculated using the Arrhenius equation. The conductivity of the molten system regularly increases with increasing temperature and decreases with increasing concentration of Dy₂O₃ or Cu₂O or both. The activation energy E_κ of the LiF-DyF₃-Dy₂O₃ and LiF-DyF₃-Cu₂O molten-salt systems increases with increasing Dy₂O₃ or Cu₂O content. The regression functions of conductance as a function of temperature (t) and the addition of Dy₂O₃ (W(Dy₂O₃)) and Cu₂O (W(Cu₂O)) can be expressed as κ=-2.08435 + 0.0068t-0.18929W(Dy₂O₃)-0.07918W(Cu₂O). The optimal electrolysis conditions for preparing the Dy-Cu alloy in LiF-DyF₃-Dy₂O₃-Cu₂O molten salt are determined to be 2.0wt% ≤ W(Dy₂O₃) + W(Cu₂O) ≤ 3.0wt% and W(Dy₂O₃):W(Cu₂O)=1:2 at 970 to 1000℃.     

Reaction behavior of trace oxygen during combustion of falling FeSi75 powder in a nitrogen flow

To explore the reaction behavior of trace oxygen during the flash combustion process of falling FeSi75 powder in a nitrogen flow, a flash-combustion-synthesized Fe-Si₃N₄ sample was heat-treated to remove SiO₂. The samples before and after the treatment were investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, and the formation mechanism of SiO₂ was investigated. The results show that SiO₂ in the Fe-Si₃N₄ is mainly located on the surface or around the Si₃N₄ particles in dense areas, existing in both crystalline and amorphous states; when the FeSi75 particles, which are less than 0.074 mm in size, fell in up-flowing hot N₂ stream, trace oxygen in the N₂ stream did not significantly hinder the nitridation of FeSi75 particles as it was consumed by the surface oxidation of the generated Si₃N₄ particles to form SiO₂. At the reaction zone, the oxidation of Si₃N₄ particles decreased the oxygen partial pressure in the N₂ stream and greatly reduced the opportunity for FeSi75 particles to be oxidized into SiO₂; by virtue of the SiO₂ film developed on the surface, the Si₃N₄ particles adhered to each other and formed dense areas in the material.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

Effect of thermal oxidation on the surface characteristics and corrosion behavior of a Ta-implanted Ti-50.6Ni shape memory alloy

A NiTi shape memory alloy (SMA) modified by Ta ion implantation was subjected to oxidation treatment in air at 723 and 873 K. Atomic force microscopy (AFM), Auger electron spectroscopy (AES), and grazing incidence X-ray diffraction (GIXRD) measurements were conducted to investigate the surface characteristics, including surface topography, elemental depth profiles, and surface phase structures. The surface roughness of the Ta-implanted NiTi increases after oxidation, and the higher the oxidation temperature is, the larger the value is. The surface of the Ta-implanted NiTi oxidized at 723 K is a nanolayer mainly composed of TiO₂/Ta₂O₅ and TiO with depressed Ni content. The Ta-implanted NiTi oxidized at 873 K is mainly covered by rutile TiO₂ in several micrometers of thickness. Potentiodynamic polarization tests indicated that the corrosion resistance of the Ta-implanted NiTi was improved after thermal oxidation at 723 K, but a negative impact was found for the Ta-implanted NiTi oxidized at 873 K.     

Effect of NaNO<Subscript>3</Subscript> concentration on anodic electrochemical behavior on the Sb surface in NaOH solution

The effect of NaNO₃ concentration on the anodic electrochemical behavior of antimony in 4 M NaOH solution was investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) analyses. The mechanism of NO₃- concentration effect on the anodic electrochemical behavior of antimony was proposed, and its availability was confirmed by experimental results. The effect of NaNO₃ on the anodic behavior of antimony in NaOH solution can be interpreted as a stepwise formation of different antimony compounds with different NaNO₃ concentrations. Metallic antimony is apt to be oxidized into Sb₂O₃ within the NaNO₃ concentration range of 0-0.48 M. NaSbO₃ can be found on the antimony surface when the NaNO₃ concentration increases gradually. Insoluable NaSbO₃ inhibits the anodic oxidation of antimony due to its shielding effect on the mass transport of the reactants and products. Surface morphology and composition were analyzed by X-ray photoelectron spectroscopy (XPS), scanning electronic microscopy (SEM), and electron dispersion spectroscopy (EDS) analyses. Results indicate that the anodic oxidation layer is composed of Sb₂O₃, NaSbO₃, and Sb. The atomic proportion of antimony in the form of NaSbO₃ increases with increasing NaNO₃ concentration due to the powerful oxidizing property of NaNO₃.     

Effect of Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on the oxidation induration mechanism of Hongge vanadium titanomagnetite pellets

As part of a research project to develop a novel clean smelting process for the comprehensive utilization of Hongge vanadium titanomagnetite (HVTM), in this study, the effect of Cr₂O₃ addition on the oxidation induration mechanism of HVTM pellets (HVTMPs) was investigated in detail. The results showed that the compressive strength of the HVTMPs was greatly weakened by the Cr₂O₃ addition, mainly because of a substantial increase in the porosity of the HVTMPs. The Cr₂O₃ addition marginally affected the phase composition but greatly affected the microstructural changes of the HVTMPs. Increased amounts of Cr₂O₃ resulted in a decrease in the uniform distribution of the hematite grains and in an increase in the Fe-Cr solid solutions (Fe_1.2Cr_0.8O₃ and Fe_0.7Cr_1.3O₃) embedded in the hematite grains. Moreover, the compact hematite was destroyed by forming a dispersed structure and the hematite recrystallization was hindered during the oxidation induration, which adversely affected the compressive strength. On the basis of these results, a schematic was formulated to describe the oxidation induration mechanism with different amounts of added Cr₂O₃. This study provides theoretical and technical foundations for the effective production of HVTMPs and a reference for chromium-bearing minerals.     

Carbothermic reduction of vanadium titanomagnetite with the assistance of sodium carbonate

The carbothermic reduction of vanadium titanomagnetite concentrate(VTC)with the assistance of Na₂CO₃was conducted in an argon atmosphere between 1073 and 1473 K.X-ray diffraction and scanning electron microscopy were used to investigate the phase transformations during the reaction.By investigating the reaction between VTC and Na₂CO₃,it was concluded that molten Na₂CO₃broke the structure of titanomagnetite by combining with the acidic oxides(Fe₂O₃,TiO₂,Al₂O₃,and SiO₂)to form a Na-rich melt and release FeO and MgO.Therefore,Na₂CO₃accelerated the reduction rate.In addition,adding Na₂CO₃also benefited the agglomeration of iron particles and the slag–metal separation by decreasing the viscosity of the slag.Thus,Na₂CO₃assisted carbothermic reduction is a promising method for treating VTC at low temperatures.     

Enhanced photocatalytic activity of electrochemically synthesized aluminum oxide nanoparticles

In this study, aluminum oxide (Al₂O₃) nanoparticles (NPs) were synthesized via an electrochemical method. The effects of reaction parameters such as supporting electrolytes, solvent, current and electrolysis time on the shape and size of the resulting NPs were investigated. The Al₂O₃ NPs were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, thermogravimetric analysis/differential thermal analysis, energy-dispersive X-ray analysis, and ultraviolet–visible spectroscopy. Moreover, the Al₂O₃ NPs were explored for photocatalytic degradation of malachite green (MG) dye under sunlight irradiation via two processes: adsorption followed by photocatalysis; coupled adsorption and photocatalysis. The coupled process exhibited a higher photodegradation efficiency (45%) compared to adsorption followed by photocatalysis (32%). The obtained kinetic data was well fitted using a pseudo-first-order model for MG degradation.     

Effect of diboron trioxide on the crushing strength and smelting mechanism of high-chromium vanadium-titanium magnetite pellets

The effect of diboron trioxide (B₂O₃) on the crushing strength and smelting mechanism of high-chromium vanadium-titanium magnetite pellets was investigated in this work. The main characterization methods were X-ray fluorescence, inductively coupled plasma-atomic emission spectroscopy, mercury injection porosimetry, X-ray diffraction, metallographic microscopy, and scanning electron microscopy-energy-dispersive X-ray spectroscopy. The results showed that the crushing strength increased greatly with increasing B₂O₃ content and that the increase in crushing strength was strongly correlated with a decrease in porosity, the formation of liquid phases, and the growth and recrystallization consolidation of hematite crystalline grains. The smelting properties were measured under simulated blast furnace conditions; the results showed that the smelting properties within a certain B₂O₃ content range were improved and optimized except in the softening stage. The valuable element B was easily transformed to the slag, and this phenomenon became increasingly evident with increasing B₂O₃ content. The formation of Ti(C,N) was mostly avoided, and the slag and melted iron were separated well during smelting with the addition of B₂O₃. The size increase of the melted iron was consistent with the gradual optimization of the dripping characteristics with increasing B₂O₃ content.     

Properties of a reaction-bonded β-SiAlON ceramic doped with an FeMo alloy for application to molten aluminum environments

An FeMo-alloy-doped β-SiAlON (FeMo/β-SiAlON) composite was fabricated via a reaction-bonding method using raw materials of Si, Al₂O₃, AlN, FeMo, and Sm₂O₃. The effects of FeMo on the microstructure and mechanical properties of the composite were investigated. Some properties of the composite, including its bending strength at 700℃ and after oxidization at 700℃ for 24 h in air, thermal shock resistance and corrosion resistance to molten aluminum, were also evaluated. The results show that the density, toughness, bending strength, and thermal shock resistance of the composite are obviously improved with the addition of an FeMo alloy. In addition, other properties of the composite such as its high-temperature strength and oxidized strength are also improved by the addition of FeMo alloy, and its corrosion resistance to molten aluminum is maintained. These findings indicate that the developed FeMo/β-SiAlON composite exhibits strong potential for application to molten aluminum environments.     

功能梯度Ni?W/Er2O3稀土纳米颗粒复合膜的电沉积

Multi-layered functionally graded (FG) structure Ni?W/Er₂O₃ nanocomposite films were prepared by continuously changing the deposition parameters, in which the Er₂O₃ and W contents varied with thickness. The microstructure and chemical composition of the electrodeposited Ni?W/Er₂O₃ films were determined by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The anti-corrosion and wear properties of the electrodeposition films were investigated by electrochemical measurement and ball-on-disk friction test. The microhardness distribution of the cross section of nanocomposites was measured by nanoindentation. The results showed that with decreasing agitation rate or increasing average current density, the contents of Er₂O₃ nanoparticles and tungsten were distributed in a gradient along the thickness, and the contents on the surface were larger. By comparison, FG Ni?W/Er₂O₃ films had better anti-corrosion and wear properties than the uniform Ni?W/Er₂O₃ films. Atomic force microscopy (AFM) and profilometry measurements indicated that Er₂O₃ nanoparticles had an effect on the surface roughness.     

Microstructure and properties of mullite-based porous ceramics produced from coal fly ash with added Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Using coal fly ash slurry samples supplemented with different amounts of Al₂O₃, we fabricated mullite-based porous ceramics via a dipping-polymer-replica approach, which is a popular method suitable for industrial application. The microstructure, phase composition, and compressive strength of the sintered samples were investigated. Mullite was identified in all of the prepared materials by X-ray diffraction analysis. The microstructure and compressive strength were strongly influenced by the content of Al₂O₃. As the Al/Si mole ratio in the starting materials was increased from 0.84 to 2.40, the amount of amorphous phases in the sintered microstructure decreased and the compressive strength of the sintered samples increased. A further increase in the Al₂O₃ content resulted in a decrease in the compressive strength of the sintered samples. The mullite-based porous ceramic with an Al/Si molar ratio of 2.40 exhibited the highest compressive strength and the greatest shrinkage among the investigated samples prepared using coal fly ash as the main starting material.     

TiO2对含铬高钛熔分渣熔化性能和黏度的影响

A study on the melting and viscosity properties of the chromium-containing high-titanium melting slag (CaO–SiO₂–MgO–Al₂O₃–TiO₂–Cr₂O₃) with TiO₂ contents ranging from 38.63wt% to 42.63wt% was conducted. The melting properties were investigated with a melting-point apparatus, and viscosity was measured using the rotating cylinder method. The FactSage 7.1 software and X-ray diffraction, in combination with scanning electron microscopy–energy-dispersive spectroscopy (SEM–EDS), were used to characterize the phase equilibrium and microstructure of chromium-containing high-titanium melting slags. The results indicated that an increase in the TiO₂ content led to a decrease in the viscosity of the chromium-containing high-titanium melting slag. In addition, the softening temperature, hemispheric temperature, and flowing temperature decreased with increasing TiO₂ content. The amount of crystallized anosovite and sphene phases gradually increased with increasing TiO₂ content, whereas the amount of perovskite phase decreased. SEM observations revealed that the distribution of the anosovite phase was dominantly influenced by TiO₂.     

Activity coefficients of NiO and CoO in CaO-Al2O3-SiO2 slag and their application to the recycling of Ni-Co-Fe-based end-of-life superalloys via remelting

To design optimal pyrometallurgical processes for nickel and cobalt recycling, and more particularly for the end-of-life process of Ni-Co-Fe-based end-of-life (EoL) superalloys, knowledge of their activity coefficients in slags is essential. In this study, the activity coefficients of NiO and CoO in CaO-Al₂O₃-SiO₂ slag, a candidate slag used for the EoL superalloy remelting process, were measured using gas/slag/metal equilibrium experiments. These activity coefficients were then used to consider the recycling efficiency of nickel and cobalt by remelting EoL superalloys using CaO-Al₂O₃-SiO₂ slag. The activity coefficients of NiO and CoO in CaO-Al₂O₃-SiO₂ slag both show a positive deviation from Raoult's law, with values that vary from 1 to 5 depending on the change in basicity. The activity coefficients of NiO and CoO peak in the slag with a composition near B=(%CaO)/(%SiO₂)=1, where B is the basicity. We observed that controlling the slag composition at approximately B=1 effectively reduces the cobalt and nickel oxidation losses and promotes the oxidation removal of iron during the remelting process of EoL superalloys.     

Influence of oxide scales on the corrosion behaviors of B510L hot-rolled steel strips

The influence of oxide scales on the corrosion behaviors of B510L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of oxide scales on the surface and cross sections of the hot-rolled steel. Raman spectroscopy and X-ray diffraction were used for the phase analysis of the oxide scales and corrosion products. The corrosion potential and impedance were measured by anodic polarization and electrochemical impedance spectroscopy. According to the results, oxide scales on the hot-rolled strips mainly comprise iron and iron oxides. The correlation between mass gain and test time follows a power exponential rule in the damp-heat test. The corrosion products are found to be mainly composed of γ-FeOOH, Fe₃O₄, α-FeOOH, and γ-Fe₂O₃. The contents of the corrosion products are different on the surfaces of the steels with and without oxide scales. The steel with oxide scales is found to show a higher corrosion resistance and lower corrosion rate.