Preparation of titanium dioxide from titania-rich slag by molten NaOH method

Preparing titanium dioxide from titania-rich slag (TiO₂ 73wt%) by molten NaOH method has been developed. The effects of temperature and reaction time on the titanium conversion were investigated. The results showed that temperature had significant influence on the titanium conversion as well as the structure of the product. About 92% of titanium in the titania-rich slag could be converted after reacting with NaOH at 500℃ for 1 h. Metatitanic acid was formed through the steps of washing treatment, acid dissolution, and hydrolysis. Well-dispersed spherical titanium dioxide particles with an average size of 0.1-0.4 μm can be obtained by calcination of metatitanic acid. In addition, the content of titanium dioxide in the product is up to 98.6wt%, which can be used as pigments after further treatment of coating and crushing.     

Behavior of NiCrAlY coating on the TC6 titanium alloy

A NiCrAlY coating was deposited on the TC6 titanium substrate by arc ion plating (ALP). The structure and morphologies of the NiCrAlY coating were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the influence of vacuum heat treatment on the element diffusion behavior was studied. The results showed that the γ'-Ni₃Al phase was precipitated on the NiCrAlY coating after heat treatment. The Ni₃(AI,Ti), TiNi, and Ti₂Ni intermetallic layers appeared at the interface from the outside to the inside at 700℃, and the thickness of the intermetallic layers increased with the increase in temperature. At 700℃ Ti and Ni were the major diffusion elements, and the diffusion of Cr was observed when the heat treatment temperature increased up to 870℃. The violent inward diffusion of Ni at 950℃ resulted in the degradation of the NiCrAlY coating.     

Preparation and performance of a cold gas dynamic sprayed high-aluminum bronze coating

By mixing preheated high-aluminum bronze powders with different amounts of Al₂O₃ powder, a low-pressure cold-sprayed coating was prepared and sprayed onto a Cr12MoV steel substrate. The hardness of the coating and the bonding strength between the coating and the substrate were tested with a HV-1000 microhardness tester and a mechanical universal testing machine. The surface microstructure, cross-section and tensile fracture surface of the coating were observed with a scanning electron microscope (SEM). Correspondingly, the influences of the preheat treatment temperature of the bronze powder and the Al₂O₃ content on the coating performance were investigated. The results indicate that the hardness of bronze powders decreased and the coating deposition rate increased after the preheating treatment of the bronze powder. The Al₂O₃ content in the mixed powders contributed to the deformation of bronze powders during the spraying process. This trend resulted in varied performance of the coating.     

Comparative study on the corrosion behavior of X52, 3Cr,and 13Cr steel in an O2-H2O-CO2 system:products,reaction kinetics,and pitting sensitivity

The corrosion behaviors of X52, 3Cr low-alloy steel, and 13Cr stainless steel were investigated in an O₂-H₂O-CO₂ environment at various temperatures and O₂-CO₂ partial-pressure ratios. The results showed that the corrosion rates of X52, 3Cr, and 13Cr steels increased with increasing temperature. The corrosion rates slowly increased at temperatures less than 100℃ and increased sharply when the temperature exceeded 100℃. In the absence of O₂, X52, 3Cr, and 13Cr exhibited uniform corrosion morphology and FeCO₃ was the main corrosion product. When O₂ was introduced into the system, various forms of Fe₂O₃ appeared on the surface of the samples. The Cr content strongly influenced the corrosion resistance. The 3Cr steel with a low Cr content was more sensitive to pitting than the X52 or 13Cr steel. Thus, pitting occurred on the surface of 3Cr when 1.25 MPa of O₂ was added; this phenomenon is related to the non-uniform distribution of Cr in 3Cr.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

Effect of niobium alloying level on the oxidation behavior of titanium aluminides at 850°C

This work addresses the alloying of titanium aluminides used in aircraft engine applications and automobiles. The oxidation resistance behavior of two titanium aluminides of α₂ + γ(Ti₃Al + TiAl) and orthorhombic Ti₂NbAl, recognized as candidates for high-temperature applications, was investigated by exposure of the alloys for 100 h in air. Thus, oxidation resistance was expressed as the mass gain rate, whereas surface aspects were analyzed using scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy, and the type of oxidation products was analyzed by X-ray diffraction and Raman spectroscopy. The orthorhombic Ti₂NbAl alloy was embrittled, and pores and microcracks were formed as a result of oxygen diffusion through the external oxide layer formed during thermal oxidation for 100 h.     

Synthesis of titanium oxycarbonitride by carbothermal reduction and nitridation of ilmenite with recycling of polyethylene terephthalate (PET)

An innovative and sustainable carbothermal reduction and nitridation (CTRN) process of ilmenite (FeTiO₃) using a mixture of polyethylene terephthalate (PET) and coal as the primary reductant under an H₂-N₂ atmosphere was proposed.The use of PET as an alternative source of carbon not only enhances the porosity of the pellets but also results in the separation of Fe from titanium oxycarbonitride (TiO_xC_yN_z) particles because of the differences in surface tension.The experiments were carried out at 1250℃ for 3 h using four different PET contents ranging from 25wt% to 100wt% in the reductant.X-ray diffraction (XRD),scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDX),and LECO elemental analysis were used to study the phases and microstructures of the reduced samples.In the case of 75wt% PET,iron distinctly separated from the synthesized TiO_xC_yN_z phase.With increasing PET content in the sample,the reduction and nitridation rates substantially increased.The synthesis of an oxycarbonitride with stoichiometry of TiO_0.02C_0.13N_0.85 with minimal intermediate titanium sub-oxides was achieved.The results also showed that the iron particles formed from CTRN of FeTiO₃ exhibited a spherical morphology,which is conducive for Fe removal via the Becher process.     

Experimental and numerical study on plasma nitriding of AISI P20 mold steel

In this study, plasma nitriding was used to fabricate a hard protective layer on AISI P20 steel, at three process temperatures (450°C, 500°C, and 550°C) and over a range of time periods (2.5, 5, 7.5, and 10 h), and at a fixed gas N₂:H₂ ratio of 75vol%:25vol%. The morphology of samples was studied using optical microscopy and scanning electron microscopy, and the formed phase of each sample was determined by X-ray diffraction. The elemental depth profile was measured by energy dispersive X-ray spectroscopy, wavelength dispersive spectroscopy, and glow dispersive spectroscopy. The hardness profile of the samples was identified, and the microhardness profile from the surface to the sample center was recorded. The results show that ε-nitride is the dominant species after carrying out plasma nitriding in all strategies and that the plasma nitriding process improves the hardness up to more than three times. It is found that as the time and temperature of the process increase, the hardness and hardness depth of the diffusion zone considerably increase. Furthermore, artificial neural networks were used to predict the effects of operational parameters on the mechanical properties of plastic mold steel. The plasma temperature, running time of imposition, and target distance to the sample surface were all used as network inputs; Vickers hardness measurements were given as the output of the model. The model accurately reproduced the experimental outcomes under different operational conditions; therefore, it can be used in the effective simulation of the plasma nitriding process in AISI P20 steel.     

采用HVOF涂层提高异种合金825和AISI 321 CO2激光焊件在900°C腐蚀盐环境中的热腐蚀性能

This study investigated the hot corrosion performance of a dissimilar weldment of Ni-based superalloy and stainless steel joined by CO₂-laser welding and improved by high-velocity oxy-fuel (HVOF) coating in a Na₂SO₄?60wt%V₂O₅ environment at 900°C. A dissimilar butt joint of AISI 321 and alloy 825 was fabricated by CO₂-laser welding with low heat input after obtaining the optimum welding parameters by bead-on-plate trials. The metallurgical and mechanical properties of the laser weldment were evaluated. The tensile test results indicated the occurrence of fracture in the base metal AISI 321 side. The HVOF process was employed to coat Ni?20wt%Cr on the weldment. To evaluate the surface morphology of the corrosion products formed on the uncoated and Ni?20wt%Cr-coated weldments, scanning electron microscopy (SEM) analysis was performed. Energy-dispersive spectroscopy (EDS) was used to determine the different elements present on the surface scales. The existence of oxide phases on the weldments was determined by X-ray diffraction (XRD). The cross sections of the weldments were characterized by SEM with EDS line mapping analysis. The results indicated that the Ni?20wt%Cr-coated weldment exhibited superior hot corrosion resistance due to the development of Cr₂O₃ and NiCr₂O₄ protective oxide scales.     

Effects of HNO3 concentration on the pit morphologies of aluminum foil etched in HNO3–HCl and HNO3–H2SO4–HCl solutions

In this work, the effects of HNO₃ concentration on the pit morphologies of high-cubic-texture aluminum foil etched in HNO₃–HCl and HNO₃–H₂SO₄–HCl solutions were investigated. When the aluminum foil was etched in HNO₃–HCl solutions, the morphologies of pits transformed from irregular tunnels to typical tunnels (as inverted pyramids) and shallow cuboids as the HNO₃ concentration in the etchant solution was increased. However, as the HCl concentration in the etchant solution was increased, the morphologies of pits transformed from shallow cuboids to typical tunnels (as inverted pyramids) and irregular tunnels. When the aluminum foil was etched in n N HNO₃–(7.2?n) N H₂SO₄–0.8 N HCl solutions, the morphologies of the pits transformed from typical tunnels (i.e., the number of sub-tunnels formed on the main tunnels increased) to irregular tunnels (corrugated tunnels and polyline tunnels) as the HNO₃ concentration in the etchant solution was increased. These effects are attributed primarily to corrosion on the (100) and (010) faces of pits being accelerated and to the (001) faces being prone to passivation to different degrees when various concentrations of HNO₃ are added to the etchant solutions.     

氧化铁/氧化锌超疏水复合材料的制备及其光催化性能

A facile approach was developed to construct Fe₂O₃-modified ZnO micro/nanostructures with excellent superhydrophobicity and photocatalytic activities. The effects of stearic acid (SA) and Fe₂O₃ on the morphological characteristics, water contact angle (WCA), and photocatalytic degradation were investigated. Superhydrophobicity results showed that WCA increased from 144° ± 2° to 154° ± 2° when the weight of SA increased from 5 to 20 mg because of the formation of a hierarchical or rough structure. Furthermore, Fe₂O₃-modified ZnO micro/nanostructure surfaces before and after SA treatment (20 mg) were chosen to evaluate the photodegradation of methylene blue (MB) dye under the support of visible light. MB degraded after 80 min of irradiation, and its photodegradation efficiencies were 91.5% at the superhydrophobic state and 92% at the hydrophilic state. This improvement in photocatalytic activity at both states might be attributed to an increase in surface area and improvement in charge carrier separation.     

利用氧化基粉煤灰粉和医疗废弃物颗粒开发无电镀镍基复合涂层 (Ni–P/粉煤灰和Ni-P/Ni–P/SiO2–Al2O3)

Recycling and reusing materials from waste have become a nexus in the development of sustainable materials, leading to more balanced technologies. In this study, we developed a composite coating by co-depositing recycled ceramic particles, pulverised fly ash (PFA) and medical ceramics (MC), into a nickel–phosphorus matrix using a typical electroless plating process. Scanning electron microscopy (SEM) images indicated well-dispersed particles in the Ni–P matrix. However, compared with the MC particles, the PFA particles were distributed scantily with a lower content in the matrix, which could be due to the less impingement effect during the co-deposition. A modified microstructure with refined grains was obtained for the PFA-incorporated composite coating, as seen in the SEM micrograph. The X-ray diffraction result of the MC-incorporated composite coating showed the formation of Ni_xSi_y phases in addition to the typical Ni₃P phases for the heat-treated electroless Ni–P coatings. Upon heat treatment, the PFA-reinforced composite coating, due to a modified microstructure, exhibited a higher microhardness up to HK_0.05 818, which is comparable to that of the traditional SiC particle-embedded composite coating (HK_0.05 825). The findings can potentially open up a new strategy to further advance the green approach for industrial surface engineering.     

SrF2颗粒涂覆增强Si/C负极电化学性能

The silicon-based material exhibits a high theoretical specific capacity and is one of the best anode for the next generation of advanced lithium-ion batteries (LIBs). However, it is difficult for the silicon-based anode to form a stable solid-state interphase (SEI) during Li alloy/de-alloy process due to the large volume change (up to 300%) between silicon and Li_4.4Si, which seriously limits the cycle life of the LIBs. Herein, we use strontium fluoride (SrF₂) particle to coat the silicon?carbon (Si/C) electrode (SrF₂@Si/C) to help forming a stable and high mechanical strength SEI by spontaneously embedding the SrF₂ particle into SEI. Meanwhile the formed SEI can inhibit the volume expansion of the silicon?carbon anode during the cycle. The electrochemical test results show that the cycle performance and the ionic conductivity of the SrF₂@Si/C anode has been significantly improved. The X-ray photoelectron spectroscopy (XPS) analysis reveals that there are fewer electrolyte decomposition products formed on the surface of the SrF₂@Si/C anode. This study provides a facile approach to overcome the problems of Si/C electrode during the electrochemical cycling, which will be beneficial to the industrial application of silicon-based anode materials.     

Fabrication and thermal stability of Ni-P coated diamond powder using electroless plating

Ni-P coated diamond powder was fabricated successfully by using electroless plating. Effects of active solutions, plating time, reaction temperature, and the components of the plating bath on the Ni-P coating were investigated systematically. Moreover, a study on the thermal stability of Ni-P coated diamond under various atmospheres was performed. The results indicate that Pd atoms absorbed on the diamond surface as active sites can consequently enhance the deposition rate of Ni effectively. The optimized plating bath and reaction conditions improve both the plating speed and the coverage rate of Ni-P electroless plating on the diamond surface. Compared to the diamond substrate, the diamond coated with Ni-P films exhibits very high thermal stability and can be processed up to 900℃ in air and 1300℃ in protective atmosphere such as H₂.     

Effect of the CaO/SiO2 mass ratio and FeO content on the viscosity of CaO-SiO2-“FeO”-12wt%ZnO-3wt%Al2O3 slags

An effective process for recycling lead from hazardous waste cathode ray tubes (CRTs) funnel glass through traditional lead smelting has been presented previously. The viscous behavior of the molten high lead slag, which is affected by the addition of funnel glass, plays a critical role in determining the production efficiency. Therefore, the viscosities of the CaO-SiO₂-"FeO"-12wt%ZnO-3wt%Al₂O₃ slags were measured in the current study using the rotating spindle method. The slag viscosity decreases as the CaO/SiO₂ mass ratio is increased from 0.8 to 1.2 and also as the FeO content is increased from 8wt% to 20wt%. The breaking temperature of the slag is lowered substantially by the addition of FeO, whereas the influence of the CaO/SiO₂ mass ratio on the breaking temperature is complex. The structural analysis of quenched slags using Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy reveals that the silicate network structure is depolymerized with increasing CaO/SiO₂ mass ratio or increasing FeO content. The[FeO₆]-octahedra in the slag melt increase as the CaO/SiO₂ mass ratio or the FeO content increases. This increase can further decrease the degree of polymerization (DOP) of the slag. Furthermore, the activation energy for viscous flow decreases both with increasing CaO/SiO₂ mass ratio and increasing FeO content.     

HOT CORROSION OF A PLASMA SPRAYED CoNiCrAlTaSiY COATING

Hot corrosion(HC) of the APS(atomospheric plasma spraying)CoNiCrAlTaSiY coating on a nickel-base superalloy GH864 has been studied. The effect of laser-treatment on hot corrosion resistance was also examined.It was shown that CoNiCrAlTaSiY coating had superior properties in resistance to hot corrosion due to the readiness of the formation of a protective Cr₂O₃ scale on the coating surface.A model for the mechanism of hot corrosion of this coating has been suggested. Hot corrosion resistance of this coating was significantly increased by the laser treatment simply because the surface of the as sprayed coating was densified by the high power laser beam.     

Si/Al、Na/Al和H2O/Na2O摩尔比对无机铝硅酸盐涂层甲醛阻隔性能的影响

Wood-based panels containing urea-formaldehyde resin result in the long-term release of formaldehyde and threaten human health. In this study, inorganic aluminosilicate coatings prepared by combining metakaolin, silica fume, NaOH, and H₂O were applied to the surfaces of wood-based panels to obstruct formaldehyde release. The Si/Al, Na/Al, and H₂O/Na₂O molar ratios of the coatings were regulated to investigate their effects on the structure and formaldehyde-resistant barrier properties of coatings. Results showed that the cracks in the coatings gradually disappeared and the formaldehyde resistance rates of the barrier increased as the Si/Al molar ratio was increased from 1.6 to 2.2. This value also increased as the Na/Al molar ratio was increased from 0.9 to 1.2 because of the improvement of the degree of polymerization. As the H₂O/Na₂O molar ratio was increased from 12 to 15, the thickness of the dry film decreased gradually and led to the reduction in the formaldehyde resistance rate. When the Si/Al, Na/Al, and H₂O/Na₂O molar ratios were 2.2, 1.2, and 12, respectively, the inorganic aluminosilicate coating showed good performance as a formaldehyde-resistant barrier and its formaldehyde resistance rate could reach up to 83.2%.     

Influence of oxide scales on the corrosion behaviors of B510L hot-rolled steel strips

The influence of oxide scales on the corrosion behaviors of B510L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of oxide scales on the surface and cross sections of the hot-rolled steel. Raman spectroscopy and X-ray diffraction were used for the phase analysis of the oxide scales and corrosion products. The corrosion potential and impedance were measured by anodic polarization and electrochemical impedance spectroscopy. According to the results, oxide scales on the hot-rolled strips mainly comprise iron and iron oxides. The correlation between mass gain and test time follows a power exponential rule in the damp-heat test. The corrosion products are found to be mainly composed of γ-FeOOH, Fe₃O₄, α-FeOOH, and γ-Fe₂O₃. The contents of the corrosion products are different on the surfaces of the steels with and without oxide scales. The steel with oxide scales is found to show a higher corrosion resistance and lower corrosion rate.     

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

In this work, an in situ synthesized TiC-reinforced metal matrix composite (MMC) coating of approximately 350–400μm thick-ness was fabricated on a gray cast iron (GCI) substrate by plasma transferred arc (PTA) surface alloying of Ti–Fe alloy powder. Microhard-ness tests showed that the surface hardness increased approximately four-fold after the alloying treatment. The microstructure of the MMC coating was mainly composed of residual austenite, acicular martensite, and eutectic ledeburite. Scanning electron microscopy (SEM) and X-ray diffraction analyzes revealed that the in situ TiC particles, which were formed by direct reaction of Ti with carbon originally contained in the GCI, was uniformly distributed at the boundary of residual austenite in the alloying zone. Pin-on-disc high-temperature wear tests were performed on samples both with and without the MMC coating at room temperature and at elevated temperatures (473 K and 623 K), and the wear behavior and mechanism were investigated. The results showed that, after the PTA alloying treatment, the wear resistance of the sam-ples improved significantly. On the basis of our analysis of the composite coatings by optical microscopy, SEM with energy-dispersive X-ray spectroscopy, and microhardness measurements, we attributed this improvement of wear resistance to the transformation of the microstruc-ture and to the presence of TiC particles.     

Grafting modification on the surface of titanium dioxide by polystyrene

Based on the technology of titanium dioxide grafting modification with polystyrene (PS), the modification mechanisms are studied and the polystyrene-grafting states on the surface of titanium dioxide have been set up. Under the synergistic actions of mechanical force, chemistry and heat, macromolecular free radicals of PS are created, at the same time, the O-O bonds of titanium dioxide are broken and the oxide free radicals produced, and the numbers of oxygen atom are increased and crystal lattice defects rich electrons are formed on the surface of titanium dioxide. The radical polymerization is the main reaction between PS and titanium dioxide and C-O bonds form in the process of modification. Multi-sites chemical adsorption also exists besides grafting between PS and titanium dioxide.