Effects of aging treatment and heat input on the microstructures and mechanical properties of TIG-welded 6061-T6 alloy joints

Aging treatment and various heat input conditions were adopted to investigate the microstructural evolution and mechanical properties of TIG welded 6061-T6 alloy joints by microstructural observations, microhardness tests, and tensile tests. With an increase in heat input, the width of the heat-affected zone (HAZ) increases and grains in the fusion zone (FZ) coarsen. Moreover, the hardness of the HAZ decreases, whereas that of the FZ decreases initially and then increases with an increase in heat input. Low heat input results in the low ultimate tensile strength of the welded joints due to the presence of partial penetrations and pores in the welded joints. After a simple artificial aging treatment at 175℃ for 8 h, the microstructure of the welded joints changes slightly. The mechanical properties of the welded joints enhance significantly after the aging process as few precipitates distribute in the welded seam.     

Influence of CO2 laser welding parameters on the microstructure, metallurgy, and mechanical properties of Mg-Al alloys

This study investigated the microstructural characteristics, metallurgy, microhardness, and tensile strength of AZ31 and AZ61 magnesium alloy weldments, fabricated in a CO₂ laser welding process with the adjustment of various parameters. The results show that the AZ31 weldment contains equiaxed grains within the fusion zone (FZ). By contrast, the FZ of the AZ61 weldment contains refined cellular grains and the partially melted zone (PMZ) contains bulk grains. We infer that the difference in aluminum content between the two magnesium alloys results in different supercooling rates and solid grain structures. For both weldments, the ultimate tensile strength (UTS) decreases following the CO₂ laser welding process. However, no significant difference is noted between the UTS of the two weldments, suggesting that tensile strength is insensitive to the Al content of the magnesium alloy. The CO₂ laser welding process is shown to increase the microhardness of both magnesium alloys. Furthermore, grain refinement is responsible for the maximum hardness in the FZ of both weldments. The AZ61 weldment has a higher content of Al, resulting in a greater grain refinement.     

First-principles calculations of the β′-Mg<Subscript>7</Subscript>Gd precipitate in Mg-Gd binary alloys

The metastable β’ phase is often the most effective hardening precipitate in Mg-Gd based alloys.In this paper,the structural,elastic and electronic properties of the recently identified β’-Mg7Gd precipitate in Mg-Gd binary alloys were investigated using first-principles calculations based on density functional theory.The lattice mismatches between the coherent β’-Mg7Gd precipitate and α-Mg matrix are discussed and used to rationalize the experimentally observed morphology of the precipitate.The mechanical properties were investigated through analysis of the single-crystal elastic constants and the polycrystalline elastic moduli.It is found that β’-Mg7Gd is brittle in nature.Strong covalent bonding in β’-Mg7Gd,as inferred from its electronic structure,further explains its mechanical properties.Our theoretical results show good agreement with experimental measurements.     

Rapid solidification of undercooled Al-Cu-Si eutectic alloys

Under the conventional solidification condition, a liquid aluminium alloy can be hardly undercooled because of oxidation. In this work, rapid solidification of an undercooled liquid Al_80.4Cu_13.6Si₆ ternary eutectic alloy was realized by the glass fluxing method combined with recycled superheating. The relationship between superheating and undercooling was investigated at a certain cooling rate of the alloy melt. The maximum undercooling is 147 K (0.18T _E). The undercooled ternary eutectic is composed of α(Al) solid solution, (Si) semiconductor and θ(CuAl₂) intermetallic compound. In the (Al+Si+θ) ternary eutectic, (Si) faceted phase grows independently, while (Al) and θ non-faceted phases grow cooperatively in the lamellar mode. When undercooling is small, only (Al) solid solution forms as the leading phase. Once undercooling exceeds 73 K, (Si) phase nucleates firstly and grows as the primary phase. The alloy microstructure consists of primary (Al) dendrite, (Al+θ) pseudobinary eutectic and (Al+Si+θ) ternary eutectic at small undercooling, while at large undercooling primary (Si) block, (Al+θ) pseudobinary eutectic and (Al+Si+θ) ternary eutectic coexist. As undercooling increases, the volume fraction of primary (Al) dendrite decreases and that of primary (Si) block increases. Supported by the National Natural Science Foundation of China (Grant Nos. 50121101, 50395105) and the Doctorate Foundation of Northwestern Polytechnical University (Grant No. CX200419)     

Mg/Al异种材料瞬间液相过冷连接工艺研究

采用瞬间液相过冷连接工艺对AZ31镁合金和5083铝合金进行连接实验,研究保温扩散时间t2对焊缝微观组织及力学性能的影响。利用SEM,EDS,XRD和微观硬度计对接头剖面的微观组织和力学性能进行表征;在拉伸试验机上测试接头拉伸强度,利用SEM对断口形貌进行分析。研究结果表明:采用瞬间液相过冷连接工艺可以实现Mg/Al异种材料的有效连接;随着保温扩散时间t2的增加,接头的抗拉强度随之提高,当t2=30 min时,接头抗拉强度最高达到20.5 MPa;拉伸断口形貌具有明显的脆性断裂的特征,铝合金侧主要有解理面和撕裂棱组成,而镁合金侧属于典型的沿晶断裂形貌;在接头处形成MgAl,Mg2Al3,Mg0.44Al0.56和Mg17Al12金属间化合物,结合界面的微观维氏硬度最高达320。     

Effects of the types of overlap on the mechanical properties of FSSW welded AZ series magnesium alloy joints

The effects of the types of overlap on the mechanical properties of the friction stir spot welding (FSSW) welded AZ series magnesium alloy joints were investigated by microstructural observations, microhardness tests, and tensile tests. The results show that the microstructure of the stir zone adjacent to the periphery of the rotating pin is mainly composed of the upper sheet. The average distance D between the longitudinal segment of the curved interface and the keyhole periphery, the tensile shear force, and the microhardness of the stir zone of the FSSW welded AZ61 alloy joint are the highest in all samples. During FSSW of AZ31 and AZ61 dissimilar magnesium alloys, the irregular deformation of the longitudinal segment of the curved interface appears, while the microhardness of the stir zone is higher when AZ61 alloy is the upper sheet. Moreover, the microhardness of the stir zone increases initially and then decreases sharply in the longitudinal test position.     

Effects of gadolinium addition on the microstructure and mechanical properties of Mg-9Al alloy

This research aims to study the significance of Gd addition (0wt%-2wt%) on the microstructure and mechanical properties of Mg-9Al alloy. The effect of Gd addition on the microstructure was investigated via X-ray diffraction (XRD), optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The Mg-9Al alloy contained two phases, α-Mg and β-Mg17Al12. Alloying with Gd led to the emergence of a new rectangular-shaped phase, Al₂Gd. The grain size also decreased marginally upon Gd addition. The ultimate tensile strength and microhardness of Mg-9Al alloy increased by 23% and 19%, respectively, upon 1.5wt% Gd addition. We observed that, although Mg-9Al-2.0Gd alloy exhibited the smallest grain size (181 μm) and the highest dislocation density (5.1×1010 m-2) among the investigated compositions, the Mg-9Al-1.5Gd alloy displayed the best mechanical properties. This anomalous behavior was observed because the Al₂Gd phase was uniformly distributed and present in abundance in Mg-9Al-1.5Gd alloy, whereas it was coarsened and asymmetrically conglomerated in Mg-9Al-2.0Gd.     

2024-T42铝合金点焊接头性能研究

为改善高强铝合金接头连接性能,提高焊接质量,研究了2024-T42铝合金回填式搅拌摩擦点焊(RFSSW)、电阻点焊和铆接3种不同接头的连接性能,采用显微组织观察试验、拉伸试验、拉剪试验和显微硬度试验等方法,对接头组织和性能进行表征与分析.结果 表明:RFSSW接头的力学性能最优,拉剪性能达到7.23 kN,较铆接和电阻...     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Influence of stacking fault energy on formation of long period stacking ordered structures in Mg–Zn–Y–Zr alloys

The influence of alloying elements on the stacking fault energy (SFE) of Mg–Y–Zn–Zr alloys was calculated by using first-principles, and the microstructure of as-cast Mg-1.05Y-0.79Zn-0.07Zr (mole fraction, %) alloy prepared by conventional casting was investigated by SEM, TEM and HRTEM. The block-like long period stacking ordered (LPSO) phase, the lamellar LPSO phase and stacking faults were observed simultaneously and the lamellar LPSO structure and stacking faults were both formed on (0001)_α-Mg habit plane and grown or extended along [01i0]_α-Mg direction. The calculation results by the first-principles showed that the addition of Y can sharply decrease the stacking fault energy of the Mg–Zn–Y–Zr alloy, while Zn slightly increases the stacking fault energy of the alloy. The influence of stacking fault energy on the formation of LPSO was discussed. It shows that LPSO may nucleate directly through stacking faults and the lower stacking fault energy was in favor of formation of LPSO.     

Microstructure s and mechanical properties of Ti3Al/Ni-based superalloy joints arc welded with Ti –Nb and Ti– Ni – Nb filler alloys

Dissimilar joining of Ti3Al-based alloy to Ni-based superalloy has been carried out using gas tungsten arc(GTA) welding technology with Ti–Nb and Ti–Ni–Nb filler alloys.The joint welded with the Ti–Nb filler alloy contained much less interfacial brittle phases than the one using the Ti–Ni–Nb filler alloy.The average room-temperature tensile strength of the joint welded with Ti–Nb was 202 MPa and the strength value of the one welded with Ti–Ni–Nb was 128 MPa.For both fillers,the weak links of the dissimilar joints were the weld/In718 interfaces.The presence of TiNi,TiNi3 and Ni3Nb intermetallic compounds in the joint welded with Ti–Ni–Nb induced microcracks at the weld/In718 interface and deteriorated the mechanical properties of the joint.And the adoption of the Ti–Nb filler alloy decreased the formation tendency of interfacial brittle phases to some extent and thus enhanced the tensile strength of the joint.     

Preparation and properties of the Ni-Al/Fe-Al intermetallics composite coating produced by plasma cladding

A novel approach to produce an intermetallic composite coating was put forward. The microstructure, microhardness, and dry-sliding wear behavior of the composite coating were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS) analysis, microhardness test, and ball-on-disc wear experiment. XRD results indicate that some new phases FeAl, Fe_0.23Ni_0.77Al, and Ni₃Al exit in the composite coating with the Al₂O₃ addition. SEM results show that the coating is bonded with carbon steel metallurgically and exhibits typical rapid directional solidification structures. The Cr₇C₃ carbide and intermetallic compounds co-reinforced composite coating has a high average hardness and exhibits an excellent wear resistance under dry-sliding wear test compared with the Cr₇C₃ carbide-reinforced composite coating. The formation mechanism of the intermetallic compounds was also investigated.     

Ti6Al4V和Al2A12的扩散连接界面组织及力学性能

采用热等静压(HIP)工艺连接Al2A12和Ti6Al4V两种不同的航空航天用材料.利用扫描电镜、能谱仪和X射线衍射仪观察连接过渡区的微观组织和组成的演化,并测试其主要的力学性能.结果表明:采用热等静压制备这两种材料的界面连接好;Ti/Al反应层界面处形成了不同的金属间化合物,例如,Al3Ti、TiAl2和TiAl;连接接头处硬度为163HV,界面连接处剪切强度达到了23MPa,比只添加镀层而无中间层的连接强度提高了约17.9%,但低于带有中间层的连接强度.由于过烧和孔隙的形成使得断裂方式是脆性断裂.由此可知,在热等静压成形过程中异种材料的元素发生了相互扩散,在扩散连接处形成了不同的金属间化合物,这些金属间化合物影响连接处的力学性能.     

Effects of Sn addition on microstructure and mechanical properties of Mg- Zn-Al alloys

The effects of Sn addition(0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in cast and extruded states were investigated, and the mechanical properties of as-extruded Mg-4Zn-1.5Al-xSn studied. The experimental results showed that the as-cast Mg-4Zn-1.5Al alloy was composed of two phases α-Mg and Mg_(32)(Al, Zn)_(49), while Sn-containing alloys consisted of α-Mg, Mg_(32)(Al, Zn)_(49) and Mg_2Sn phases, and Mg_(32)(Al, Zn)_(49) was not detected after extruding due to that the most of them dissolved into the matrix during the homogenized treatment. The addition of Sn refined the grains of as-cast and as-extruded Mg-Zn-Al alloys obviously. It was noted that the basal texture intensity reduced with increasing Sn content significantly in as-extruded Mg-Zn-Al alloys. The tensile tests results indicated that Sn addition improve the tensile strength of the extruded alloys,while it had a harmful effect on the ductility. When the addition of Sn was 2 wt%, the ultimate tensile strength(UTS), yield strength(YS) and elongation(ε_f) of the alloy were 280 MPa, 147 MPa and 17.4%, respectively.     

Characteristics of AZ31 Mg alloy joint using automatic TIG welding

The automatic tungsten-inert gas welding (ATIGW) of AZ31 Mg alloys was performed using a six-axis robot. The evolution of the microstructure and texture of the AZ31 auto-welded joints was studied by optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and electron backscatter diffraction. The ATIGW process resulted in coarse recrystallized grains in the heat affected zone (HAZ) and epitaxial growth of columnar grains in the fusion zone (FZ). Substantial changes of texture between the base material (BM) and the FZ were detected. The {0002} basal plane in the BM was largely parallel to the sheet rolling plane, whereas the c-axis of the crystal lattice in the FZ inclined approximately 25° with respect to the welding direction. The maximum pole density increased from 9.45 in the BM to 12.9 in the FZ. The microhardness distribution, tensile properties, and fracture features of the AZ31 auto-welded joints were also investigated.     

Microstructure and mechanical properties of the welding joint filled with microalloying 5183 aluminum welding wires

In this study, 7A52 aluminum alloy sheets of 4 mm in thickness were welded by tungsten inert gas welding using microalloying welding wires containing traces of Zr and Er. The influence of rare earth elements Zr and Er on the microstructure and mechanical properties of the welded joints was analyzed by optical microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, hardness testing, and tensile mechanical properties testing. Systematic analyses indicate that the addition of trace amounts of Er and Zr leads to the formation of fine Al₃Er, Al₃Zr, and Al₃(Zr,Er) phases that favor significant grain refinement in the weld zone. Besides, the tensile strength and hardness of the welded joints were obviously improved with the addition of Er and Zr, as evidenced by the increase in tensile strength and elongation by 40 MPa and 1.4%, respectively, and by the welding coefficient of 73%.     

Mg-8Zn-4Al-(0～1)Sr镁合金铸态组织中的第二相研究

通过扫描电镜观察(SEM)、能谱分析(EDS)、X射线衍射分析(XRD)以及差热分析(DSC)等实验手段,系统地研究了添加微量Sr元素(质量分数0～1%)对铸态Mg-8Zn-4Al(ZA84)镁合金组织中的第二相种类的影响,并阐明了第二相形成与演变的内在机理。实验结果表明:未添加Sr元素的铸态Mg-8Zn-4Al合金组织由Q准晶相和少量Mg_(32)(Al, Zn)_(49)相组成。添加Sr元素后,合金铸态组织中均存在Al_4Sr和Mg_(32)(Al, Zn)_(49)相;其中Al_4Sr相随Sr含量增加而增加,Mg_(32)(Al, Zn)_(49)相随Sr含量增加而减少。在Mg_(32)(Al, Zn)_(49)相中Sr元素以未固溶和固溶两种形式存在,其中未固溶Sr元素的Mg_(32)(Al, Zn)_(49)相具有相对较高的Zn原子浓度和较低的Al原子浓度。相关结果将为第二相析出强化型Mg-8Zn-4Al合金的高强化与耐热化设计提供必要的理论支撑。     

Acylation of nitriles to β-ketonitriles catalyzed by a heterometallic alkoxide cluster of neodymium and sodium： NdNa8（O^tBu）10（OH）

Catalytic acylation of nitriles with esters in the presence of 10 mol% NdNa8(OtBu)10(OH) is developed.The procedure is suitable for both enolizable and nonenolizable esters and affords β-ketonitriles in moderate to high yields.The heterometallic alkoxide cluster NdNa8(OtBu)10(OH) is structurally characterized by X-ray diffraction,and a mechanism for the production of β-ketonitriles using the cluster is proposed and verified.     

A Novel Degradation Pathway of Zn（dmid） （ phen）2 in Pyridine

The light-oxidation degradation processes of Zn(dmid)(phen)2(dmid = 4, 5-dimercapto-1,3-dithiole-2 one, phen = 1,10-phenanthroaline) in pyridine solvent has been monitored, h has been found under the light, dmid^2- of Zn(dmid)(phen)2 in pyridine solution could generate NCS^- and NCS^-replaces dmid^2- to form Zn(NCS)2 (phen)2 simultaneously. The crystal structure of Zn(NCS)2 (phen)2 has been determined. In the crystal of Zn(NCS)2 (phen)2. two NCS^- ligands are arranged in syn-configuration, and there is strong π-π interaction between the two adjacent parallel phen.     

Effect of sintering temperature on phase evolution of Al_(86)Ni_6Y_(4.5)Co_2La_(1.5) bulk amorphous composites synthesized via mechanical alloying and spark plasma sintering

Al_(86)Ni_6Y_(4.5)Co_2La_(1.5) amorphous powders were synthesized by mechanical alloying for 200 h. Subsequent consolidation was performed via spark plasma sintering in the temperature range of 250 ℃ to 500 ℃ at the pressure of 500 MPa. The role of viscous flow on densification was investigated by studying the viscosity change of the amorphous phase at different consolidation temperatures. The decrease in viscosity at higher sintering temperatures resulted in better particle bonding and densification of consolidated samples. The formation of only FCC Al was observed in the consolidated samples at sintering temperatures ≤ 300 ℃ and the intermetallic phases formed at temperatures ≥ 400 ℃. The mechanical properties of the bulk samples were measured by Vickers microhardness and nanoindentation tests. The testing results showed that the average values of microhardness, nanohardness and elastic modulus of the sample consolidated at 500 ℃ were 3.06 ± 0.14 GPa,4.85 ± 1.14 GPa and 89.53 ± 9.25 GPa, respectively. The increase in hardness and elastic modulus of the higher temperature consolidated samples is attributed to the improvement in particle bonding, densification and distribution of various hard intermetallic phases in the amorphous matrix.