Interface microstructure and formation mechanism of ultrasonic spot welding for Al–Ti dissimilar metals

The present study focuses on interface microstructure and joint formation. AA6061 aluminum alloy(Al) and commercial pure titanium(Ti) joints were welded by ultrasonic spot welding(USW). The welding energy was 1100–3200 J. The Al–Ti joint appearance and interface microstructure were observed mainly via optical microscopy and field emission scanning electron microscopy. Results indicated that a good joint can be achieved only with proper welding energy of 2150 J. No significant intermetallic compound(IMC) was found under all conditions. The high energy barriers of Al–Ti and difficulties in diffusion were the main reasons for the absence of IMC according to kinetic analysis. The heat input is crucial for the material plastic flow and bonding area, which plays an important role in the joint formation.     

Effect of ECAP temperature on microstructure and mechanical properties of Al–Zn–Mg–Cu alloy

The effect of equal channel angular pressing(ECAP) at different temperatures(room temperature, 120,150 and 180 °C) on microstructure and mechanical properties of Al-7075 solid solution alloy was investigated. Microstructure of the specimens was examined using orientation imaging microscopy,transmission electron microscopy as well as X-ray diffractometer, and mechanical properties were measured by Vickers microhardness and tensile tests. Microstructural investigations showed that after3 or 4 passes of ECAP, fi ne grains with average grain sizes in range of 300–1000 nm could be obtained at different ECAP temperatures. Increasing ECAP temperature from 120 to 180 °C caused a decrease in mechanical properties as a result of increasing grains and precipitates sizes, decreasing fraction of high angle boundaries and also transformation of η′ into η phase, while increasing ECAP temperature from RT to 120 °C leads to an increase in mechanical properties due to the formation of small η′ precipitates. So it can be concluded that ECAP process at 120 °C is the optimum process for attaining maximum mechanical properties. Quantitative estimates of various strengthening mechanisms revealed that the improvement of mechanical properties was mainly attributed to grain re fi nement strengthening, precipitation strengthening and dislocation strengthening.     

Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

Tailoring of microstructure and martensitic transformation of nanocrystalline Ti–Ni-Hf shape memory thin film

The amorphous Ti-Ni-Hf thin films with the specific compositions were prepared from single Ti-Ni-Hf alloy target by adjusting processing parameters of direct current magnetron sputtering deposition. Prior to the crystallization,a glass transition occurred in the present Ti-Ni-Hf thin films. The annealed Ti-Ni-Hf thin films were characterized by the nano-crystalline. With the annealing temperature increasing, the grain size firstly increased and then decreased owing to the presence of(Ti,Hf)_2Ni precipitate. Two endothermic and exothermic peaks corresponding to B19'■B2 martensitic transformation in heating and cooling curves were observed for the Ti-Ni-Hf thin films with the lower annealing temperature and shorter annealing time, which was closely related to the inhomogeneous composition. However, the Ti-Ni-Hf thin films annealed at higher annealing temperature and longer annealing time showed the single stage B19'■B2 martensitic transformation. In addition, the martensitic transformation temperatures firstly increased and then decreased with the annealing temperatures rising.     

Effect of Zn addition on microstructure and mechanical properties of an Al–Mg–Si alloy

In the present work, an Al–0.66Mg–0.85Si–0.2Cu alloy with Zn addition was investigated by electron back scattering diffraction(EBSD), high resolution electron microscopy(HREM), tensile and Erichsen tests. The mechanical properties of the alloy after pre-aging met the standards of sheet forming. After paint baking, the yield strength of the alloy was improved apparently. GP(Ⅱ) zones and η’phases were formed during aging process due to Zn addition. With the precipitation of GP zones, β″ phases, GP(Ⅱ) zones and η’phases, the alloys displayed excellent mechanical properties.     

Effects of solidification parameters on microstructure and mechanical properties of continuous columnar-grained Cu–Al–Ni alloy

Effects of melt temperature and casting speed on microstructure and mechanical properties of Cu-14%Al-3.8%Ni(mass fraction) alloy wires fabricated by continuous unidirectional solidification technology were investigated.It was found that the average size of columnar grain in the alloy decreased and grain boundary turned clear and straight with increasing the casting speed at a given melt temperature.When the melt temperature was up to 1 280℃,theβ_1 phase gradually transformed into lozenged and lanciformγ...     

Stability of thermal cycling and high temperature mechanical properties for Ti–V–Al–B lightweight shape memory alloy

The microstructure of the Ti–V–Al shape memory alloy with refined grain and in-situ TiB phase was modified by doping minor Boron (B), which contributes to the superior mechanical performances and strain recovery characteristics. Compared with other quaternary Ti–V–Al-X alloys, the Ti–V–Al–B alloy showed the largest ultimate tensile stress due to the solution strengthening, grain refinement and precipitation strengthening of in-situ TiB phase. Moreover, the Ti–V–Al alloy added 0.1 ?at.%B possessed the maximum yield stress of 701 ?MPa and the largest tensile fracture strain of 27.6% at the temperature of 150 ?°C. Meanwhile, the excellent strain recovery characteristics with fully recoverable strain of 4% could be obtained due to B addition. Besides, B addition suppressed the precipitation of ω phase during thermal cycling and further improved the thermal cycling stability of the Ti–V–Al alloy.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Saturation phenomenon of Ce and Ti in the modification of Al–Zn–Si filler metal

Cerium and titanium were added to an Al–42Zn–6.5Si brazing alloy, and the subsequent microstructures of the brazing alloy and the 6061 Al alloy brazing seam were investigated. The microstructures of filler metals and brazed joints were characterized by scanning electron microscopy and X-ray energy dispersion spectrometry. A new Ce–Ti phase formed around the silicon phase in the modified filler metal and this saturation phenomenon was analyzed. Interestingly, following brazing of the 6061 alloy, there is no evidence of the Ce–Ti phase in the brazing seam. Because of the mutual solubility of the brazing alloy and base metal, the quantity of the solvent increases, and the solute Ce and Ti atoms assume an undersaturated state.     

Influence of different rolling processes on microstructure and strength of the Al–Cu–Li alloy AA2195

The influence of different rolling processes on precipitation behaviour, crystallography texture, grain morphology, and their consequent effects on tensile properties for Al–Cu–Li alloy AA2195 was investigated in the present work. The H-T8 samples (hot rolled ?+ ?T8) presented better tensile strength and ductility (with serious strength anisotropy) than the HC-T8 samples (hot rolled ?+ ?cold rolled ?+ ?T8), due to their different microstructures and textures. The higher dislocation density was found in the H-T8 samples, which promoted the nucleation of main strengthening phase T₁ in the matrix and suppressed the grain boundary precipitation, resulted in better strength and ductility. The increase of the dynamic recovery (DRV) during hot rolling enhanced the generation of Brass texture, and brought serious strength anisotropy. The cold rolling was performed after the hot-rolling process for the HC-T8 samples which increased deformation energy and resulted in full recrystallization of the deformed microstructure during the following solution treatment. The formation of recrystallized microstructure reduced the dislocation density and the heterogeneous precipitate nucleation positions which limited the strengthening phase precipitation in matrix and accelerated the precipitation along grain boundaries, resulted in fewer T₁ precipitates, coarse grain-boundary precipitates (GBPs), and wider precipitate-free zones (PFZs). The localized strain may be concentrated on the grain boundary to induce the dislocation pile-up, breaking of the GBPs, and intergranular fracture during stretching.     

A Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous filler metal for improving the strength of Ti–6Al–4V alloy brazing joint

Ti_(50)Zr_(27)Cu_8Ni_4Co_3Fe_2Al_3Sn_3(at%) amorphous filler metal with low Cu and Ni contents in a melt-spun ribbon form was developed for improving mechanical properties of Ti–6Al–4V alloy brazing joint through decreasing brittle intermetallics in the braze zone. Investigation on the crystallization behavior of the multicomponent Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous alloy indicates the high stability of the supercooled liquid against crystallization that favors the formation of amorphous structure. The Ti–6Al–4V joint brazed with this Ti-based amorphous filler metal with low total content of Cu and Ni at 1203K for 900s mainly consists of α-Ti, β-Ti,minor Ti–Zr-rich phase and only a small amount of Ti_3Cu intermetallics, leading to the high shear strength of the joint of about 460 MPa. Multicomponent composition design of amorphous alloys is an effective way of tailoring filler metals for improving the joint strength.     

Rapid directionally solidified microstructure characteristic and fracture behaviour of laser melting deposited Nb–Si–Ti alloy

Aiming at achieving fine and directionally-solidified microstructure of Nb-Si based alloy,Nb,Si and Ti powder particles were utilized as the raw materials,and laser melting deposition(LMD) experiments were conducted with1500 W and 2000 W laser power,respectively.The microstructure characteristic,micro-hardness,and indentation fracture toughness were examined by scanning electron microscope(SEM),X-ray energy dispersive spectrometer(XEDS) and X-ray diffraction(XRD).The results showed that the two ...     

Preparation and mechanism study of bulk pure rare-earth metals with amorphous and nanocrystalline structures

The preparation and the mechanism study of bulk pure rare-earth metals with amorphous and nanocrystalline structures, which were produced by spark plasma sintering (SPS), were carried out in this paper. With different processing parameters, the amorphous, two phases of amorphous and nanocrystalline, and complete nanocrystalline microstructures have been obtained. The nano-grain sizes in the bulk nanocrystalline materials are found smaller than the original powder particles sizes, which may change the conventional viewpoint that the grains in the sintered bulk are generally coarser than the raw powder particles. The technique developed in the present work can be extended to the preparation of many other nano bulk metal materials, and thus enables the studies of the nano-size effects on the physical, chemical and mechanical properties of bulk nano materials.     

Effect of rolling geometry on the mechanical properties,microstructure and recrystallization texture of Al–Mg–Si alloys

The effect of rolling geometry on mechanical properties, microstructure, and recrystallization texture of Al–Mg–Si alloys was studied by means of tensile tests, microstructural observations, and electron backscatter diffraction measurements. The results reveal that the elongation and the average plasticity strain ratio(r) values of the T4P(pre-aging plus natural aging)-treated alloy sheet with a rolling geometry value between 1 and 3 are somewhat higher than those of the T4P-treated sheet with a rolling geometry value between 3 and 6. The deformation and recrystallization microstructures of the sheet with a rolling geometry value between 1 and 3 are more uniform than those of the sheet with a rolling geometry value between 3 and 6. The former also possesses somewhat higher surface quality. H {001}110 and Goss {110}001 orientations are the main recrystallization texture components for the former case, whereas the latter case only includes H{001}110 orientation. Texture gradients are present in the two alloy sheets. Shear texture component F on the surface of the sheet with a rolling geometry value between 3 and 6 and its higher texture gradients have revealed that non-uniform deformation occurred during cold rolling. The effects of texture on the yield strength and r value were also discussed.     

Effects of alloying and high-temperature heat treatment on the microstructure of Nb–Ti–Si based ultrahigh temperatur e alloys

The phase co mpositions, microstructure and especi ally phase i nterfaces in the as-cast and heat-treated Nb– Ti–Si based ultrahigh temperature alloys have been investigated. It is shown that β(Nb,X)5Si3 and γ(Nb,X)5Si3 are the primary p hase s in the Nb–22Ti–16Si–5Cr–5Al (S1) (at%) and Nb–20Ti–16Si–6C r–4Al–5Hf–2B–0.06Y (S2) (at% ) alloys, respectively. The Nb solid solution (Nbss) is the primary phase in Nb–22Ti–14Si–5Hf–3Al–1. 5B –0.0 6Y (S3) (at%) alloy . An orientation relationship between Nbss and γ(Nb,X)5Si3 was determine d to be (1-10)Nb//(101-0)γ and [111]Nb//[0001]γ in the as-cast S2 and S3 alloys. Some original β(Nb,X)5Si3 transfor med into α(Nb,X)5Si3 because Al and Cr diffused from the β(Nb,X)5Si3 to Nbss during heattreatment at 1500 °C for 50 h in the S1 alloy. Mean while, Ti diffused from Nbss to β(Nb,X)5Si3, which induced a Ti to generate near the interface between Nbss and Ti-rich β(Nb,X)5Si3. The orientation relationship between the newl y-formed a Ti and previous Nbss was (110 )Nb//(1-10-1) αTi and [001]Nb//(12-3-1)αTi. Among the ( Nb,X)5Si3 phases , the contents o f Cr and Al in β(Nb,X)5Si3 are n earl y the same as those in γ(Nb,X)5Si3 but obviously hi gher than those in the α(Nb,X)5Si3, where as the content of Si in α(Nb,X)5Si3 is nearly the same a s that in γ(Nb,X)5Si3 but higher than that in the β(Nb,X)5Si3     

Further mechanism of α/β interphase boundary evolution and dynamic globularization of Ti–5Al–2Sn–2Zr–4Mo–4Cr at elevated temperature deformation

The evolution characterization of the α/β interphase boundaries of the isothermally compressed Ti–5Al–2Sn–2Zr–4Mo–4Cr with lamellar microstructure was carried out via electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). The effect of the α/β interphase boundary evolution on the dynamic globularization was discussed, and the nucleation model for the β recrystallized grain at the cusp of α lath in the late stage of deformation in terms of the classic nucleation theory was established. The mean α/β interface deviation angle from Burgers orientation relationship (BOR) increased continuously up to 18.9° with the increasing strain from 0.1 to 0.5, which was dominated by the continuous dynamic recrystallization. Restoration of BOR between α and β phases at the strains of 0.7 and 0.9 occurred due to the occurrence of recrystallized α and β grains following BOR, which was rationalized by a nucleation model considering the stored energy of deformation provided the driving force for nucleation at the cusp of α lath. Loss of coherency of α/β interphase boundaries at a strain about 0.3 was responsible for accelerating the dynamic globularization of α lamellae since the energy of α/β interphase boundaries increased up to the maximum value when the non-coherent α/β interphase boundaries were formed. Restoration of coherency of α/β interphase boundaries due to the recrystallization nucleation in the late stage of deformation did not substantially affect the dynamic globularization since the α/α intraphase high-angle boundaries (HAGBs) were formed and the most α/β interphase boundaries were non-coherent.     

Effect of particle size distribution on the microstructure,texture, and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure, texture, and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties, microstructure, and texture of the alloy. The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture. After the pre-aging treatment and natural aging treatment (T4P treatment), in contrast to the sheet with a uniform particle size distribution, the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio (r) and strain hardening exponent (n). After solution treatment, the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution. Additionally, they possess almost identical weak recrystallization textures, and their textures are dominated by CubeND {001}<310> and P {011}<122> orientations.     

Effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties,microstructure,and texture of the alloy.The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture.After the pre-aging treatment and natural aging treatment(T4 P treatment),in contrast to the sheet with a uniform particle size distribution,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio(r) and strain hardening exponent(n).After solution treatment,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution.Additionally,they possess almost identical weak recrystallization textures,and their textures are dominated by CubeND {001}310 and P {011}122 orientations.     

Effect of heat treatment on the microstructure and mechanical properties of structural steel–mild steel composite plates fabricated by explosion welding

Two dissimilar steel plates, structural steel and mild steel, were joined by explosion welding to form a composite. The composite was then heat-treated by quenching at 840°C for 30 min followed by tempering at 200°C for 3 h. The microstructure was investigated under an optical microscope and a scanning electron microscope. The mechanical properties were measured using Vickers microhardness and Charpy impact tests. The results show a deformed interface with typical wave features at the welding zone, but no defects were observed. Moreover,the ferrite in the parent plate in the weld zone was elongated due to the strong plastic deformation from the explosion. After heat treatment, the hardness of the flyer plate(structural steel) was over HV0.2 800, while that of the parent plate(mild steel) was HV0.2 200. The increase in hardness was due to the presence of martensite. Moreover, the average impact energy was increased from 18.5 to 44.0 J following heat treatment;this is because of the formation of recrystallized grains at the weld interface, which is due to the dynamic recovery and local recrystallization,and the strong elemental diffusion that occurred between the two plates.