Fluorescence and sensitization performance of phenylene-vinylene-substituted polythiophene

A new kind of polythiophene derivative, Poly(3-{2-[4-(2-ethylhexyloxy)-phenyl]-vinyl}-2,2′-bithiophene) (PTh), was applied in dye-sensitized solar cell to extend the light response of nanocrystalline TiO2 electrode. UV-vis absorption and fluorescence spectra were employed to investigate the interaction of PTh with nanocrystalline TiO2. The absorption coefficient of the PTh was high in visible part of spec- trum, and the fluorescence emission of the PTh can be efficiently quenched by TiO2 nanoparticles ow- i...     

Comparison between P25 and anatase-based TiO<Subscript>2</Subscript> quasi-solid state dye sensitized solar cells

Pure anatase TiO2 films have been made via hydration of titanium isopropoxide using a sol-gel tech-nique, while mixed TiO2 films which contained both anatase and rutile TiO2 were made from commercial P25 powder. Quasi-solid state dye-sensitized solar cells were fabricated with these two kinds of mesoporous films and a comparison study was carried out. The result showed that the open-circuit photovoltages （Voc） for both kinds of cells were essentially the same, whereas the short-circuit photo-currents （1sc） of the anatase-based cells were about 33% higher than that of the P25-based cells. The highest photocurrent intensity of the anatase-based cell was 6.12 mA/cm^2 and that of the P25-based cell was 4.60 mA/cm^2. Under an illumination with the light intensity of 30 mW/cm^2, the corresponding energy conversion efficiency was measured to be 7.07% and 6.89% for anatase-based cells and P25-based cells, respectively.     

Modification of TiO2 nanotubes arrays by CdS and their photoelectrocatalytic hydrogen generation properties

In order to realize hydrogen generation under visible light, novel CdS/TiO2 nanotubes arrays are developed by electrochemical anodizaUon of Ti in 0.15 mol/L NHTF ＋ 0.08 mol/L H2C2O4 electrolyte. The diameter of the nanotube is 80-100 nm and the length is approximately 550 nm. The CdS nano-particles are deposited on the TiO2 nanotubes arrays by chemical bath deposition （CBD） in the ammonia-thiourea system. A 300 W Xe lamp is used as the light source, CdS/TiO2 nanotube arrays are used as the photoanode with the application of 1.0 V bath voltage, and 0.1 mol/L Na2S ＋ 0.04 mol/L Na2SO3 solution is used as the electrolyte, then the rate of photoelectrocatalytic hydrogen generation is 245.4 μL/（h·cm^2）. This opens new perspectives for photoelectrocatalytic hydrogen generation by using CdS/TiO2 nanotubes arrays.     

Preparation and performance of dye-sensitized solar cells based on ZnO-modified TiO<Subscript>2</Subscript> electrodes

The ZnO-modified TiO₂ electrode was prepared by adding Zn(CH₃COO)₂·2H₂O to the TiO₂ colloid during the sol-gel production process, and was used in dye-sensitized solar cells (DSCs). The open circuit voltage (V _OC) and fill factor (ff) of the cells were improved significantly. The performances of the ZnO-modified TiO₂ electrode such as dark current, transient photocurrent, impedance, absorption spectra, and flat band potential (V _fb) were investigated. It is found that the interface charge recombination impedance increases and V _fb shifts about 200 mV toward the cathodic potential. The effect mechanism of ZnO modification on the performance of DSCs may be that ZnO occupies the surface states of the TiO₂ film.     

TiO2-based building materials: Above and beyond traditional applications

In the 1910s, TiO₂ began to be used in building materials as pigments and opacifier due to its excellent optical property. Since the photocatalytic property of TiO₂ was observed in 1972, its application field was expanded to air cleaning and sterilization. Thereafter, people added TiO₂ into building materials to develop novel and facile building materials. These materials were widely used for air cleaning, sterilization, self-cleaning, anti-fogging, decoration, and building cooling. The combination of building and other functions can serve simultaneously. Although TiO₂-based building materials have bright prospects, some aspects such as improving the stability and enhancing photoactive performance of the materials are of importance for future research. Supported by the National High Technology Research and Development Program (“863” Program) of China (Grant No. 2007AA061402), Chinese Key Technology Research and Development Program of the Eleventh Five-year Plan (Grant No. 2006BAJ02A08), Hangzhou Science & Technology Development Program (Grant No. 20061133B27) and Research Fund for the Doctoral Program of Higher Education (Grant No. 20070335197)     

Preparation of Zn-doped TiO2 nanotubes electrode and its application in pentachlorophenol photoelectrocatalytic degradation

Zn-doped titanium oxide （TiO2） nanotubes electrode was prepared on a titanium plate by direct anodic oxidation and immersing method in sequence. Field emission scanning electron microscopy （FESEM） showed that the Zn-doped TiO2 nanotubes were well aligned and organized into high density uniform arrays with diameter ranging from 50 to 90 nm. The length and the thickness were about 200 and 15 nm respectively. TiO2 anatase phase was identified by X-ray diffraction （XRD）. X-ray photoelectronspectroscopy （XPS） indicated that Zn ions were mainly located on the surface of TiO2 nanotubes in form of ZnO clusters. Compared with TiO2 nanotubes electrode, about 20 nm red shift in the spectrum of UV-vis absorption was observed. The degradation of pentachlorophenol （PCP） in aqueous solution under the same condition （initial concentration of PCP： 20 mg/L; concentration of Na2SO4：0.01 mol/L and pH： 7.03） was carried out using Zn-doped TiO2 nanotubes electrode and TiO2 nanotubes electrode. The degradation rates of PCP using Zn-doped TiO2 nanotubes electrode were found to be twice and 5.8 times as high as that using TiO2 nanotubes electrode by UV radiation （400 μw/cm^2） and visible light radiation （4500 μw/cm^2）, respectively. 73.5% of PCP was removed using Zn-doped TiO2 nanotubes electrode against 45.5% removed using TiO2 nanotubes electrode in 120 min under UV radiation. While under visible light radiation, the degradation efficiency of PCP was 18.4% using Zn-doped TiO2 nanotubes electrode against 3.2% using TiO2 nanotubes electrode in 120 min. The optimum concentration of Zn doping was found to be 0.909%. The PCP degradation efficiencies of the 10 repeated experiments by Zn-doped TiO2 nanotubes electrode were rather stable with the deviation within 3.0%.     

Si衬底掺杂浓度对InGaN/Si异质单结太阳电池性能的影响

【目的】研究p-Si衬底掺杂浓度对InGaN/Si异质单结太阳电池性能的影响,为制备高效太阳电池提供理论基础。【方法】将器件的n-InGaN掺杂浓度固定为10~(16 )cm~(-3),在改变p-Si衬底掺杂浓度N_A的情况下,采用一维光电子和微电子器件结构分析模拟软件(AMPS-1D)对InGaN/Si异质单结太阳电池器件的各项性能参数进行模拟。【结果】随着掺杂浓度N_A的升高,电池的电流密度J_(SC)和填充因子FF随之升高,当到达一定高的掺杂浓度范围时(N_A5.00×10~(17)cm~(-3)),J_(SC)基本保持不变,约为28.12mA/cm~2,FF保持在0.85左右且变化不大。开路电压V_(OC)和光电转换效率E_(ff)与掺杂浓度的大小呈正相关关系,随着N_A的增大,V_(OC)、E_(ff)缓慢增大。【结论】高掺杂浓度下的太阳电池具有较好的光电转换效率。低掺杂浓度的太阳电池光电转换效率较低,这是因为其对应的尖峰势垒高度和宽度均较大,影响了光生载流子的输运。     

Photovoltaic properties of MEH-PPV/TiO2 nanocomposites

Photovoltaic properties of photodiodes based on nano-TiO2 and poly[2-methoxy,5-（2＇-ethlhexyloxy）-p-phenylenevinylene] （MEH-PPV） composites are investigated. By comparing composite devices with the same weight of TiO2 （nanoparticles and nanotubes）：MEH-PPV, it was found that the device with TiO2 nanotubes exhibited better performance. By further optimizing the weight radio of TiO2 nanotubes： MEH-PPV, we gained the device with a short circuit current density of 9.27μA/cm^2 with a light intensity of 16.7mW/cm^2 at the 500 nm wavelength, the highest open-circuit voltage of 1.1V, and a photosensitivity of 332 at reverse bias of -0.6V. The photosensitivity is improved by a factor of 33 compared with the undoped MEH-PPV device.     

Preparation and magnetic properties of CoFe2O4/TiO2 composite films

Using （Ti（OC4H9）4） and metal chlorates as starting materials, CoFe2O4/TiO2 composite films were prepared by sol-gel method. The effects of heat treatment temperature and pH of the precursor on microstructure and magnetic properties were studied. The phase structure of the samples was examined by X-ray diffraction. The microstructure was examined by scanning electron microscope, atomic force microscope and polarized microscope. The magnetic property was measured by vibrating sample magnetometer. The results show that the crystals of different phases grow up independently. CoFe2O4 is uniformly embedded into the TiO2 matrix in the prepared composite films, and the growth of composite films is dependent on the heat treatment temperatures and PH of the precursor. The average size of CoFe2O4 crystal is 19 nm in Nanocomposite film prepared when the heat treatment temperature is 800℃ and the pH of the precursor is between 2 and 3. The magnetism of the composite films is enhanced as the heat treatment temperature increases.     

TiO<Subscript>2</Subscript>@MgO core-shell film: Fabrication and application to dye-sensitized solar cells

In this study,TiO2@MgO core-shell film was obtained by using a simple chemical bath deposition method to coat a thin MgO film around TiO2 nanoparticles. The core-shell configuration was characterized by X-ray diffractometer (XRD),scanning elec-tron microscopy (SEM),energy dispersive X-ray spectroscopy (EDX),and high-resolution transmission electron microscopy (HRTEM). Lattice fringes were observed for the TiO2 particles,and the MgO shell showed an amorphous structure,revealing a clear distinction between the core and shell materials. Applying the core-shell film as photoanode to the dye-sensitized solar cells (DSSCs),it shows a superior performance compared to the pure TiO2 electrode. Under the illumination of simulated sunlight (75 mW-cm-2),the short circuit photocurrent (Jsc),the open circuit photovoltage (Voc),and the fill factor (fF) are 8.80 mA-cm-2,646 mV,and 0.69,respectively,and the conversion efficiency (η) in-creased by 21.8% (from 4.32% to 5.26%) when dipping for opti-mum condition.     

Compression behavior and equation of state of Ni77P23 amorphous alloy

The compression behavior of Ni77P23 amorphous alloy is investigated at room temperature in a diamond-anvil cell instrument using insitu high pressure energy dispersive X-ray diffraction with a syn- chrotron radiation source. The equation of state is determined by fitting the experimental data accord- ing to Birch-Murnaghan equation: -ΔV/V0=0.08606P-3.2×10-4P2 5.7×10-6P3. It is found that the structure of Ni77P23 amorphous alloy is stable under pressures up to 30.5 GPa.     

Magnetoelectric and converse magnetoelectric res ponses in TbxDy1-xFe2-y alloy ＆ Pb（Mg1/3Nb2/3）（1-x）TixO3 crystal laminated composites

Measured results of magnetoelectric （ME） and converse magnetoelectric （CME） effects of TbxDy1-xFe2-y/ Pb（Mg1/3Nb2/3）（1-x）TixO3/TbxDy1-xFe2-y （TD/PMNT/TD） and PMNT/TD/PMNT laminated composites are presented. ME effect was determined by measuring laminate voltage output under a Helmholtz-generated AC field biased by a DC field （0-1 kOe） （1Oe = 79.58 A/m）. The CME effect was measured by recording the voltage induced in a solenoid encompassing the ME sample while exposed to a DC bias field and PMNT layer driven by a 10 V AC source. The ME and CME responses in the two laminated structure are linear. The highest values of ME coefficients in TD/PMNT/TD and PMNT/TD/PMNT composites are 384 mV/Oe and 158 mV/Oe, respectively, while the highest values of CME coefficients in the two composites are 118 mG/V and 162 mG/V （1 G=10^-4 T）, respectively.     

Fabrication of the 19-filament Fe/Cu clad MgB2 wire via in situ powder-in-tube method

Using commercial amorphous B powder (92% in purity) and Mg powder (99% in purity) as starting materials, 19-filament Fe/Cu clad MgB2 wires were fabricated by an in situ powder-in-tube method. Heat treatment was performed at 700℃ for 1 h under an argon gas atmosphere. The influence of Mg/B ratio on the microstructure and superconducting properties of the wires was investigated. It was found that the major phases of MgB2 wires were MgB2 accompanied with relatively small amounts of MgO and Fe2B impurities. With 5% excess Mg addition, the onset TC slightly decreased. However, the transport JC at 4.2 K and 4 T reached 1.07×104 A·cm-2, increasing by a factor of 1.4 compared to the stoichiometric sample. Moreover, the Mg1.05B2 sample showed an improved field dependence of JC, suggesting that less voids and smaller grain size of the Mg1.05B2 core lead to better grain connectivity and stronger flux pinning.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase in MnO2 nanosheet film

A novel material MnO2 nanosheet has been used as the support matrix for the immobilization of horseradish peroxidase （HRP）. HRP entrapped in MnO2 nanosheet film exhibits facile direct electron transfer with the electron transfer rate constant of 6.86 s^-1. The HRP/MnO2 nanosheet film gives a reversible redox couple with the apparent formal peak potential （E^0＇） of -0.315 V （vs. Ag/AgCl） in pH 6.5 phosphate buffer solution （PBS）. The formal potential E^0＇ of HRP shifts linearly with pH with a slope of -53.75 mV.pH^-1, denoting that an electron transfer accompanies single-proton transportation. The immobilized HRP shows an electrocatslytic activity to the reduction of H2O2. The response time of the biosensor for H2O2 is less than 3 s, and the detection limit is 0.21 μmol · L^-1 based on signal/noise = 3.     

Theoretical study of adsorption and dissociation of NH3 on the Ir{110}（1×2） surface

The adsorption and dissociation of NH3 on Ir{110}（1×2） have been investigated using the density- functional calculations at a coverage of 0.25 ML. The adsorption sites, energy, and geometries were obtained for NH3, NH2, and H adsorptions on the surface. The transition state for NH3 dissociation on Ir{110}（1×2） was also identified. It was found that NH3 is adsorbed preferentially at the ridge atop site, while NH2 and H are adsorbed at the ridge bridge site. The activation barrier of NH3 dissociation is 78.4 kJ/mol, which is very close to the NH3 adsorption energy of 90.0 kJ/mol. This indicates that the desorption and dissociation of NH3 on Ir{110}（1×2） are very competitive, which is consistent with the recent experimental results.     

Dielectric properties of low dielectric constant Ba0.60Sr0.40Mg0.15Ti0.85O3-Mg2TiO4 composite thin films for tunable applications

Ba0.60Sr0.40Mg0.15Ti0.85O3-xmol%Mg2TiO4 （x = 0-40 mol%） （BSTM-MT） composite thin films were fabricated by sol-gel method. The precursor solution of these composite thin films was prepared through mixing the Ba0.80Sr0.40Mg0.15Ti0.85O3 and Mg2TiO4 solution. The microstructures and dielectric tunability of composite thin films were investigated. The dielectric constant of composite thin films can be tailored from 155 to 55 by changing the concentration of Mg2TiO4. The dielectric loss of these composite thin films were still kept below 0.01 and the tunability was above 20% at a dc-applied electric field of 500 kV/cm. Suitable dielectric constant, low dielectric loss, and high tunability of this kind of composite thin films can be useful for potential microwave tunable applications.     

Effect of the contact distance on transport properties of an orsanic molecular device

Using a spatially symmetric phenyldithiolate molecule sandwiched between two gold electrodes as model system and through shifting one electrode from symmetric contact site to form asymmetric contact, we investigated the properties of electronic transport in such a device by the first-principles. It was found that the/（G ）-V characteristics of a device show significant asymmetry and the magnitudes of current and conductance depend remarkably on the variation of molecule-metal distance at one of the two contacts. Namely, an asymmetric contact would lead to the weak rectifying effects on the current-voltage characteristics of a molecular device. The analysis shows that the HOMO is responsible for the resonant tunneling and its shift due to the charging of the device while the bias voltage is the intrinsic origin of asymmetric/（G）- Vcharacteristics.     

Optimization of polymer electrolytes for quasi-solidstate dye-sensitized solar cells

The dye-sensitized nanocrystalline TiO2 thin filmsolar cells (DSSCs) have attracted much attention since1990s[1— , due to their high light to electrical energy 4]conversion efficiency. So far, many studies have beenmade on the use of liquid electrolytes such as acetonitrile,3-methoxypropionitrile and a mixture of ethylene/pro-pylene carbonate (EC/PC) containing I? /I3 redox cou-?ple. A light to electrical energy conversion efficiency of7%— 12% has been obtained for DSSC using liquid e…     

Fabrication and superconducting properties of nano-SiC doped MgB2 tapes

Nano-SiC doped MgB2 tapes were prepared by the in situ powder-in-tube method. Heat treatment was performed at 650℃ for 1 h. XRD data indicate that SiC particles had reacted with the MgB2 during sintering process. MgB2 core seemed to be denser after SiC doping, and the critical temperature was slightly depressed. The critical current density Jc of the SiC doped tapes was significantly enhanced in magnetic fields up to 14 T compared to the undoped ones. For the 5% SiC doped samples, Jc was in- creased by a factor of 32 at 4.2 K, 10 T. The enhancement of Jc-B properties in SiC doped MgB2 tapes is considered to be due to the enhancement of grain linkages and the introduction of effective flux pining centers. The substitution of B by C in MgB2 grains is thought to be the main reason for the improve- ment of the flux pinning ability in SiC doped MgB2 tapes.     

Graded bandgap semiconductor thin film photoelectrodes

A graded bandgap oxide semiconductor thin film electrode was designed in order to obtain a photoelec-trochemically stable photoelectrode, with wide absorption range. The graded bandgap Ti_1−x V _x O₂ film electrode was prepared by heating the stacked layers of V/Ti in varying ratios, which were coated on the substrate by the sol-gel method using the starting solution with various V/Ti ratios. XPS result showed that the composition gradient was achieved for the film. The Ti_1−x V _x O₂ film electrode was found to be photoelectrochemically stable. Its photovoltage was about 360 mV. Obvious visible light photoresponse was observed for the Ti_1−x V _x O₂ film electrode. Compared with the pure TiO₂ electrode, the photocurrent onset potential of the Ti_1−x V _x O₂ film electrode was shifted positively, probably because the accumulation of vanadium at the electrode surface causes the recombination of the electrons and holes, and the lowest level of the conduction band of Ti_1−x V _x O₂ is lower than that of TiO₂. Impedance analysis showed that the donor density of the Ti_1−x V₂O₂ film electrode was higher than that of TiO₂ film electrode.