玉米秸秆还原浸出高铁低品位锰矿研究

采用"玉米秸秆硫酸预处理—浸出"工艺处理含Mn 9.63%(质量分数)的朝阳锰矿.通过试验考察用硫酸对玉米秸秆进行预处理的时间、秸秆用量、温度、硫酸浓度和浸出温度对锰浸出率的影响.试验表明,在秸秆用量2.5 g、时间10 min、硫酸浓度1.2 mol/L、温度80℃时预处理秸秆,浸出温度为90℃的条件下,锰的浸出率达92%,杂质铁溶出率仅为20%.玉米秸秆处理前后FTIR分析结果表明,对秸秆进行硫酸预处理能够破坏难降解的木质素结构,有利于提高锰的浸出效果.     

用硫酸亚铁浸出低品位锰矿

了用硫酸亚铁还原浸出低品位氧化锰矿的工艺过程，考察了硫酸亚铁的加入量、硫酸初浓度、瓜在温度和浸出的时间等各种工艺参数的影响，讨论了浸出过程的动力学，实验结果表明，在最佳实验条件下，锰的浸出率可达９８％以上，浸出反应速度可用ｌｎ方程描述。     

玉米秸秆和稻草-硫酸还原浸出低品位软锰矿

研究了以低品位软锰矿为原料,用玉米秸秆和稻草为混合还原剂,在硫酸介质中还原浸出锰的效果.通过单因素实验确定了玉米秸秆和稻草-硫酸还原浸锰的适宜工艺条件,该适宜工艺条件如下:软锰矿粒径为109μm,玉米秸秆和稻草的质量比为1∶1.5,玉米秸秆和稻草还原剂与软锰矿的质量比为3∶10,硫酸浓度为3.0 mol/L,液固比为10 m L/g,反应温度为90℃,反应时间为80 min.在适宜的浸出工艺条件下,软锰矿中锰的浸出率可达97%以上,锰的浸出效果较好.     

芦丁还原浸出低品位软锰矿的研究

为了研究糖蜜酒精废液中有机物还原浸出软锰矿的机理,采用芦丁为还原剂,在酸性介质中直接浸出低品位软锰矿。通过正交实验和单因素实验,研究了芦丁浓度、硫酸浓度、反应温度、浸出时间等因素对锰浸出率的影响,并对反应过程机理进行了初步探讨。实验结果表明,影响锰浸出率的主要因素依次为反应温度、硫酸浓度、浸出时间和芦丁浓度;当硫酸初始浓度2.35 mol/L,芦丁初始浓度0.041 mol/L,反应温度90℃,浸出时间90 m in时,锰浸出率达94.9%。     

用硫酸亚铁浸出同时沉淀铁矾法处理低品位锰矿

研究了用硫酸亚铁浸出同时沉淀黄钠铁矾的方法处理低品位软锰矿的过程．在该过程中,软锰矿中的ＭｎＯ２被还原成ＭｎＳＯ４同时ＦｅＳＯ４被氧化并以黄钠铁矾的形态沉淀．沉淀产生的酸可直接用于ＭｎＯ２浸出．考察了硫酸、硫酸亚铁和硫酸钠的加入量及温度等参数对锰浸出和沉铁效率的影响．讨论了过程动力学．实验结果表明,锰浸出率和沉铁效率（质量分数）在最佳条件下可分别达到９６％和９２％．     

生物质焦焙烧还原低品位软锰矿及其动力学

采用生物质焦和活性炭粉作还原剂,在管式炉中进行了低品位软锰矿焙烧还原对比试验.分别研究了焙烧温度、焙烧时间、生物质焦用量等条件对软锰矿还原率的影响,对焙烧产物进行了X射线衍射分析.结果表明,生物质焦在焙烧时间和还原效率上优于活性炭粉;软锰矿焙烧还原依次经历Mn O2→Mn2O3→Mn3O4→Mn O过程;在焙烧温度为800℃,焙烧时间为50 min,生物质焦用量为10%时,软锰矿还原率可达98%以上,在此基础上导出了还原动力学方程,并证实还原过程由界面化学反应控制,表观活化能为43.896 k J·mol-1.     

高铁锰矿直接还原及其还原行为

采用JSM-5600LV型扫描电镜和FEI-Sirion200场发射扫描电子显微镜分析高铁锰矿矿石性质结构,并对高铁锰矿直接还原进行研究。实验结果表明:赤铁矿和少量褐铁矿呈粒状(1~2μm)不均匀分布于板状的方铁锰矿中,其中49.53%(质量分数)的锰与铁氧化物以类质同象存在。热力学研究表明:在还原过程中,铁和锰的氧化物还原遵循逐级还原的原则,同时,锰的高价氧化物优先还原。通过SEM图分析可知,随着还原温度的升高,高铁锰矿在还原过程中,金属铁颗粒不断迁移、聚集、兼并长大,采用无烟煤在1 100℃还原,100 min时,铁氧化物中81.03%(质量分数)的铁还原成金属铁,金属铁中局部仍存在MnO。     

用草酸在硫酸溶液中从中性浸出渣中还原浸出铟

The present study evaluates the reductive leaching of indium from indium-bearing zinc ferrite using oxalic acid as a reducer in sulfuric acid solution. The effect of main factors affecting the process rate, including the oxalic-acid-to-sulfuric-acid ratio, stirring rate, grain size, temperature, and the initial concentration of synergic acid, was precisely evaluated. The results confirmed the acceptable efficiency of dissolving indium in the presence of oxalic acid. The shrinking-core model with a chemical-reaction-controlled step can correctly describe the kinetics of indium dissolution. On the basis of an apparent activation energy of 44.55 kJ/mol and a reaction order with respect to the acid concentration of 1.14, the presence of oxalic acid was found to reduce the sensitivity to temperature changes and to increase the effect of changes in acid concentration. Finally, the equation of the kinetic model based on the factors under study is presented.     

黄铁矿强化生物浸出低品位磷矿

进行了嗜酸氧化亚铁硫杆菌、嗜酸氧化硫硫杆菌与嗜酸氧化亚铁钩端螺旋菌的混合菌强化浸出低品位磷矿的实验研究.结果表明:由于试样中硫含量低,不利于该磷矿的生物浸出.提出了在浸矿体系中添加黄铁矿来强化浸出的措施.考察了细菌种类、磷矿与黄铁矿配比以及初始Fe2+质量浓度等参数对磷浸出率的影响.采用驯化菌浸出该磷矿,能获得最佳的浸出效果,其适宜的工艺参数为初始Fe2+质量浓度9g.L-1、磷矿与黄铁矿质量比1:2.5,经过20d浸出,磷的浸出率可达95%.     

含铁低品位氧化锌矿石浸出研究

针对含铁低品位氧化锌矿石,进行了碱性浸出与硫酸浸出研究.其中碱性浸出主要考察了采用不同浸出剂时浸出时间以及采用氨水——氯化铵作浸出剂时浸出温度对锌、铁浸出率的影响;硫酸浸出主要考察了硫酸初始浓度、矿浆液固比以及不同硫酸初始浓度时浸出温度和不同浸出温度时浸出时间对锌、铁浸出率的影响.研究结果表明,碱性浸出时锌浸出率不到5...     

Hydrometallurgical leaching and kinetic modeling of low-grade manganese ore with banana peel in sulfuric acid

Manganese was leached from a low-grade manganese ore(LGMO) using banana peel as the reductant in a dilute sulfuric acid medium. The effects of banana peel amount, H_2SO_4 concentration, reaction temperature, and time on Mn leaching from the complex LGMO were studied. A leaching efficiency of ～98% was achieved at a leaching time of 2 h, banana peel amount of 4 g, leaching temperature of 120°C,manganese ore amount of 5 g, and sulfuric acid concentration of 15 vol%. The phase, microstructural, and chemical analyses of LGMO samples before and after the leaching process confirmed the successful leaching of manganese. Furthermore, the leaching process followed the shrinking core model and the leaching rate was controlled by a surface chemical reaction(1-(1-x)~(1/3)=kt) mechanism with an apparent activation energy of 40.19 k J·mol~(-1).     

Preparation of manganese sulfate from low-grade manganese carbonate ores by sulfuric acid leaching

In this study, a method for preparing pure manganese sulfate from low-grade ores with a granule mean size of 0.47 mm by direct acid leaching was developed. The effects of the types of leaching agents, sulfuric acid concentration, reaction temperature, and agitation rate on the leaching efficiency of manganese were investigated. We observed that sulfuric acid used as a leaching agent provides a similar leaching efficiency of manganese and superior selectivity against calcium compared to hydrochloric acid. The optimal leaching conditions in sulfuric acid media were determined; under the optimal conditions, the leaching efficiencies of Mn and Ca were 92.42% and 9.61%, respectively. Moreover, the kinetics of manganese leaching indicated that the leaching follows the diffusion-controlled model with an apparent activation energy of 12.28 kJ·mol-1. The purification conditions of the leaching solution were also discussed. The results show that manganese dioxide is a suitable oxidant of ferrous ions and sodium dimethyldithiocarbamate is an effective precipitant of heavy metals. Finally, through chemical analysis and X-ray diffraction analysis, the obtained product was determined to contain 98% of MnSO₄·H₂O.     

Reductive leaching of manganese from low-grade pyrolusite ore in sulfuric acid using pyrolysis-pretreated sawdust as a reductant

Manganese (Mn) leaching and recovery from low-grade pyrolusite ore were studied using sulfuric acid (H₂SO₄) as a leachant and pyrolysis-pretreated sawdust as a reductant. The effects of the dosage of pyrolysis-pretreated sawdust to pyrolusite ore, the concentration of sulfuric acid, the liquid/solid ratio, the leaching temperature, and the leaching time on manganese and iron leaching efficiencies were investigated. Analysis of manganese and iron leaching efficiencies revealed that a high manganese leaching efficiency was achieved with low iron extraction. The optimal leaching efficiency was determined to be 20wt% pyrolysis-pretreated sawdust and 3.0 mol/L H₂SO₄ using a liquid/ solid ratio of 6.0 mL/g for 90 min at 90℃. Other low-grade pyrolusite ores were tested, and the results showed that they responded well with manganese leaching efficiencies greater than 98%.     

Reductive leaching of low-grade manganese ore with pre-processed cornstalk

Cornstalk is usually directly used as a reductant in reductive leaching manganese. However, low utilization of cornstalk makes low manganese dissolution ratio. In the research, pretreatment for cornstalk was proposed to improve manganese dissolution ratio. Cornstalk was preprocessed by a heated sulfuric acid solution (1.2 M of sulfuric acid concentration) for 10 min at 80°C. Thereafter, both the pretreated solu-tion and the residue were used as a reductant for manganese leaching. This method not only exhibited superior activity for hydrolyzing corn-stalk but also enhanced manganese dissolution. These effects were attributed to an increase in the amount of reductive sugars resulting from lignin hydrolysis. Through acid pretreatment for cornstalk, the manganese dissolution ratio was improved from 50.14%to 83.46%. The pre-sent work demonstrates for the first time the effective acid pretreatment of cornstalk to provide a cost-effective reductant for manganese leaching.     

响应面法优化葡萄糖还原浸出半氧化锰矿的研究

采用响应面法优化葡萄糖还原浸出半氧化锰矿的工艺,以锰浸出率为响应值,对硫酸用量/矿量、葡萄糖用量/矿量、氟化铵用量/矿量和浸取时间四因素进行建模。结果表明,这些因素与锰浸出率的关系符合二次模型,各个因素对锰浸出率影响均极其显著,各个因素的二次方以及硫酸用量/矿量与葡萄糖用量/矿量的交互作用对锰浸出率影响较显著。最优工艺条件为：硫酸用量/矿量0.880 g/g、葡萄糖用量/矿量0.059 g/g、氟化铵用量/矿量0.04 g/g、浸取时间6 h。在此条件下,锰浸出率为93.09%,与模型预测值93.18%无显著差异,而相同条件下未加氟化铵的锰浸出率为82.37%。     

石煤钠化焙烧料酸浸动力学

研究了石煤钠化焙烧料硫酸浸出过程中,浸出剂初始浓度、搅拌速度和浸出温度对浸出率的影响,并对浸出过程动力学进行了分析. 结果表明:浸出剂初始浓度和浸出温度对钒浸出率有显著影响,搅拌速度对钒浸出率影响不大;该浸出过程符合核收缩模型,与化学反应控制动力学方程式相吻合,浸出反应的表观活化能为50.88kJ·mol-1,浸出过程控制步骤为化学反应控制.     

A primary study of simultaneous leaching of silver containing manganese ore and a sphalerite concentrate

It is demonstrated that a low grade, silver containing manganese deposit can be exploited by reaction with a ZnS concentrate. In the process, Mn（IV） is reduced to Mn（II） and the ZnS converted to ZnSO4. In the process, Mn and Zn are solubilized. By studying the effects of quantity of reducing agent and sulfuric acid added and of time, temperature and liquid-to-solid ratio on the leaching process, the optimum technological conditions have been achieved un- der which the amount of manganese leached was 98 %. The silver can be removed from remaining solids by adding ammonia liquor. Then by adding hydrazine hydrate, sponge silver with purity up to 99 % can be obtained with a recovery of 87 %.     

碱性氧化铜矿产氨菌浸出特性

为了研究碱性氧化铜矿产氨菌浸出特性,分析了产氨菌浸矿过程对矿石的作用.将云南某矿的碱性氧化铜矿置于含菌培养液、去菌培养液和氨水等5种浸矿溶液中,在同一条件下进行摇瓶浸矿实验,剖析溶液中各可能的浸矿因子.研究结果表明:产氨菌产氨能力较强,尿素培养液中氨质量浓度最大达8.93 g·L-1;产氨量与细菌含量呈正相关关系,细菌含量越高,产氨量越大;产氨菌主要通过产氨间接浸矿,此外产氨菌和其代谢产物都能直接作用于矿石,浸矿能力细菌产氨>细菌>细菌代谢产物,三者比值约为12:5:4.     

Effect of desliming on the magnetic separation of low-grade ferruginous manganese ore

In the present investigation, magnetic separation studies using an induced roll magnetic separator were conducted to beneficiate low-grade ferruginous manganese ore. The feed ore was assayed to contain 22.4% Mn and 35.9% SiO₂, with a manganese-to-iron mass ratio (Mn:Fe ratio) of 1.6. This ore was characterized in detail using different techniques, including quantitative evaluation of minerals by scanning electron microscopy, which revealed that the ore is extremely siliceous in nature and that the associated gangue minerals are more or less evenly distributed in almost all of the size fractions in major proportion. Magnetic separation studies were conducted on both the as-received ore fines and the classified fines to enrich their manganese content and Mn:Fe ratio. The results indicated that the efficiency of separation for deslimed fines was better than that for the treated unclassified bulk sample. On the basis of these results, we proposed a process flow sheet for the beneficiation of low-grade manganese ore fines using a Floatex density separator as a pre-concentrator followed by two-stage magnetic separation. The overall recovery of manganese in the final product from the proposed flow sheet is 44.7% with an assay value of 45.8% and the Mn:Fe ratio of 3.1.     

含碳酸盐脉石氧化铜矿的酸浸动力学

针对碳酸盐脉石对氧化铜矿酸浸动力学的影响进行探讨,研究了温度、酸度、矿石粒径、液固质量比、振荡速度等因素对含碳酸盐脉石氧化铜矿浸出的影响.结果表明,高温、高酸度、高液固质量比、小粒径和高振荡速度利于矿石的浸出,但碳酸盐脉石使得酸耗增加.考虑浸出成本确定合理的浸出条件为温度303 K、酸度35 g·L-1、矿石粒径0.074~0.125 mm、液固质量比3﹕1以及振荡速度180 r·min-1,浸出180 min后铜浸出率达53.6%.对浸出前后矿石表面形貌进行分析.结果显示碳酸盐脉石与酸反应后在矿石表面形成CaSO4·2H2 O沉淀,覆盖在颗粒表面,限制了矿石颗粒孔裂隙的发育.基于收缩未反应核模型对浸出动力学进行分析,发现碳酸盐脉石反应生成的沉淀阻碍了浸出反应,固体产物层扩散为浸出反应的控制步骤,反应的表观活化能为8.65 kJ·mol-1.