Effect of Yb_2O_3 doping on the grain boundary of NiFe_2O_4–10NiO-based cermets after sintering

xY b2O3–15(20Ni–Cu)/(85- x)(NiF e2O4–10NiO)(x = 0, 0.25, 0.5, 0.75, 1.0, 2.0, and 10.0) cermets for aluminum electrolysis were prepared to investigate the effect of Yb2O3 doping on the grain boundary of the cermets after sintering. The results showed that each interface was very clear and that with increasing Yb2O3 content, most of the Yb was evenly distributed at the grain boundary. Moreover, according to the phase composition and microstructural analysis by X-ray diffraction(XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy(SEM/EDX), and electron probe microanalysis(EPMA), YbF eO 3 was produced along the grain boundary. The YbF eO 3 was concluded to not only have formed from the interaction between the NiF e2O4 or Fe2O3 component and Yb2O3 at the grain boundary of the cermets, but also from the decomposition of NiF e2O4 into NiO and Fe2O3 and the subsequent reaction of Fe2O3 with Yb2O3. Thus, the production of YbF eO 3 resulted in a cermet with high relative density, good electrical conductivity, and good corrosion resistance.     

Effect of Al2O3 on the viscosity of CaO-SiO2-Al2O3-MgO-Cr2O3 slags

We investigated the effect of Al2O3 content on the viscosity of CaO-SiO2-Al2O3-8wt%MgO-1wt%Cr2O3(mass ratio of CaO/SiO2 is 1.0,and Al2O3 content is 17wt%-29wt%)slags.The results show that the viscosity of the slag increases gradually with increases in the Al2O3 content in the range of 17wt%to 29wt%due to the role of Al2O3 as a network former in the polymerization of the aluminosilicate structure of the slag.With increases in the Al2O3 content from 17wt%to 29wt%,the apparent activation energy of the slags also increases from 180.85 to 210.23 kJ/mol,which is consistent with the variation in the critical temperature.The Fourier-transform infrared spectra indicate that the degree of polymerization of this slag is increased by the addition of Al2O3.The application of Iida’s model for predicting the slag viscosity in the presence of Cr2O3 indicates that the calculated viscosity values fit well with the measured values when both the temperature and Al2O3 content are at relatively low levels,i.e.,the temperature range of 1673 to 1803 K and the Al2O3 content range of 17wt%-29wt%in CaO-SiO2-Al2O3-8wt%MgO-1wt%Cr2O3 slag.     

Effect of magnesium on the aluminothermic reduction rate of zinc oxide obtained from spent alkaline battery anodes for the preparation of Al–Zn–Mg alloys

The aluminothermic reduction of zinc oxide (ZnO) from alkaline battery anodes using molten Al may be a good option for the elaboration of secondary 7000-series alloys. This process is affected by the initial content of Mg within molten Al, which decreases the surface tension of the molten metal and conversely increases the wettability of ZnO particles. The effect of initial Mg concentration on the aluminothermic reduction rate of ZnO was analyzed at the following values: 0.90wt%, 1.20wt%, 4.00t%, 4.25wt%, and 4.40wt%. The ZnO particles were incorporated by mechanical agitation using a graphite paddle inside a bath of molten Al maintained at a constant temperature of 1123 K and at a constant agitation speed of 250 r/min, the treatment time was 240 min and the ZnO particle size was 450-500 mesh. The results show an increase in Zn concentration in the prepared alloys up to 5.43wt% for the highest initial concentration of Mg. The reaction products obtained were characterized by scanning electron microscopy and X-ray diffraction, and the efficiency of the reaction was measured on the basis of the different concentrations of Mg studied.     

Effect of sintering temperature on the preparation of Cu–Ti3SiC2 metal matrix composite

Ti3SiC2 has the potential to replace graphite as reinforcing particles in Cu matrix composites for applications in brush,electrical contacts and electrode materials.In this paper the fabrication of Cu-Ti3SiC2 metal matrix composites prepared by warm compaction powder metallurgy forming and spark plasma sintering(SPS) was studied.The stability of Ti3SiC2 at different sintering temperatures was also studied.The present experimental results indicate that the reinforcing particles in Cu-Ti3SiC2 composites are not stable at and above 800℃.The decomposition of Ti3SiC2 will lead to the formation of TiC and/or other carbides and TiSi2.If purity is the major concern,the processing and servicing temperatures of the Cu-Ti3SiC2 composite should be limited to 750℃ or lower.The composites prepared by warm compaction forming and SPS sintering at 750℃ have lower density when compared with the composites prepared by SPS sintering at 950℃,but their electrical resistivity values are very close to each other and even lower.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Effect of B2O3 on the aqueous tape casting and microwave properties of Li2O–Nb2O5–TiO2 ceramics

The effect of B2O3 addition on the aqueous tape casting, sintering, microstructure and microwave dielectric properties of Li2O-Nb2O5-TiO2 ceramics has been investigated. The tape casting slurries exhibit a typical shear-thinning behavior without thixotropy, but the addition of B2O3 increases the viscosity of the slurries significantly. It was found that doping of B2O3 can decrease the tensile strength, strain to failure and density of the green tapes. The sintering temperature could be lowed down to 900℃ with the addition of 2 wt% B2O3 due to the liquid phase effect. No secondary phase is observed. The addition of B2O3 does not induce much degradation on the microwave dielectric properties. Optimum microwave dielectric properties of εr 67, Q×f 6560 GHz are obtained for Li2O-Nb2O5-TiO2 ceramics containing 2 wt% B2O3 sintered at 900 1C. It represents that the ceramics could be promising for multilayer low-temperature co-fired ceramics (LTCC) application.     

Effects of HNO3 concentration on the pit morphologies of aluminum foil etched in HNO3–HCl and HNO3–H2SO4–HCl solutions

In this work, the effects of HNO₃ concentration on the pit morphologies of high-cubic-texture aluminum foil etched in HNO₃–HCl and HNO₃–H₂SO₄–HCl solutions were investigated. When the aluminum foil was etched in HNO₃–HCl solutions, the morphologies of pits transformed from irregular tunnels to typical tunnels (as inverted pyramids) and shallow cuboids as the HNO₃ concentration in the etchant solution was increased. However, as the HCl concentration in the etchant solution was increased, the morphologies of pits transformed from shallow cuboids to typical tunnels (as inverted pyramids) and irregular tunnels. When the aluminum foil was etched in n N HNO₃–(7.2?n) N H₂SO₄–0.8 N HCl solutions, the morphologies of the pits transformed from typical tunnels (i.e., the number of sub-tunnels formed on the main tunnels increased) to irregular tunnels (corrugated tunnels and polyline tunnels) as the HNO₃ concentration in the etchant solution was increased. These effects are attributed primarily to corrosion on the (100) and (010) faces of pits being accelerated and to the (001) faces being prone to passivation to different degrees when various concentrations of HNO₃ are added to the etchant solutions.     

Effect of the CaO/SiO2 mass ratio and FeO content on the viscosity of CaO–SiO2–"FeO"–12wt%ZnO–3wt%Al2O3 slags

An effective process for recycling lead from hazardous waste cathode ray tubes (CRTs) funnel glass through traditional lead smelting has been presented previously. The viscous behavior of the molten high lead slag, which is affected by the addition of funnel glass, plays a critical role in determining the production efficiency. Therefore, the viscosities of the CaO–SiO2–"FeO"–12wt%ZnO–3wt%Al2O3 slags were measured in the current study using the rotating spindle method. The slag viscosity decreases as the CaO/SiO2 mass ratio is in-creased from 0.8 to 1.2 and also as the FeO content is increased from 8wt% to 20wt%. The breaking temperature of the slag is lowered sub-stantially by the addition of FeO, whereas the influence of the CaO/SiO2 mass ratio on the breaking temperature is complex. The structural analysis of quenched slags using Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy reveals that the silicate network structure is depolymerized with increasing CaO/SiO2 mass ratio or increasing FeO content. The [FeO6]-octahedra in the slag melt increase as the CaO/SiO2 mass ratio or the FeO content increases. This increase can further decrease the degree of polymerization (DOP) of the slag. Furthermore, the activation energy for viscous flow decreases both with increasing CaO/SiO2 mass ratio and increasing FeO content.     

Effect of the CaO/SiO2 mass ratio and FeO content on the viscosity of CaO-SiO2-“FeO”-12wt%ZnO-3wt%Al2O3 slags

An effective process for recycling lead from hazardous waste cathode ray tubes (CRTs) funnel glass through traditional lead smelting has been presented previously. The viscous behavior of the molten high lead slag, which is affected by the addition of funnel glass, plays a critical role in determining the production efficiency. Therefore, the viscosities of the CaO-SiO₂-"FeO"-12wt%ZnO-3wt%Al₂O₃ slags were measured in the current study using the rotating spindle method. The slag viscosity decreases as the CaO/SiO₂ mass ratio is increased from 0.8 to 1.2 and also as the FeO content is increased from 8wt% to 20wt%. The breaking temperature of the slag is lowered substantially by the addition of FeO, whereas the influence of the CaO/SiO₂ mass ratio on the breaking temperature is complex. The structural analysis of quenched slags using Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy reveals that the silicate network structure is depolymerized with increasing CaO/SiO₂ mass ratio or increasing FeO content. The[FeO₆]-octahedra in the slag melt increase as the CaO/SiO₂ mass ratio or the FeO content increases. This increase can further decrease the degree of polymerization (DOP) of the slag. Furthermore, the activation energy for viscous flow decreases both with increasing CaO/SiO₂ mass ratio and increasing FeO content.     

Effect of MTECl on the functional expression of TCRαβ~ + 3G11~- 6C10~-CD4~+CD8~- thymocyte subset

A murine CD4+ thymocyte subset with phenotype of TCRαβ + 3G11- 6C10- CD4 + CD8- CD69 +/- HSAmed/locontains the cells in relatively functional matured status. The functional property of the cells in this subset is characterized by the unique pattern of cytokine production at transitional stage from Th0 to Th2 type with the latter being the dominant type. After being co-cultured with murine thymic medullary epithelial cell line (MTEC1) cells, a murine thymic medullary type epithelial cell line, the TCRαβ(T 3G11 6C10-CD4 + CD8- CD69+/- HSAmed/l? thy-mocytes, has exhibited significantly higher levels of proliferation capability and IL-6 production, whereas the production of IL-4 and IL-10 is suppressed after co-culturing with MTECl. By contrast, MTECl could not induce thymocytes to secrete Th1 type of cytokines. The results suggest that MTECl can regulate functional status of this thymocyte subset and induce them to develop into a specialized Th2 subset.     

Theoretical study on the lithium bond interaction of furan homologues C4H4Y （Y=O,S） with LiCH3 via DFT and MP2

The optimizations geometries and interaction energy corrected by BSSE of the complexes between C4H4Y （Y=O, S） and CHiLi have been calculated at the B3LYP/6-311＋＋G^＊＊ and MP2/6-311＋＋G^＊＊ levels. Three complexes were obtained. Abnormally, the calculations showed that all the C10--Li14 bond lengths increased obviously but the blue-shift of C10-Li14 stretching frequency occurred after formed complexes. The calculated binding energy with basis set super-position error （BSSE） and zero-point vibrational energy corrections of complexes I-III is -45.757, -35.700 and -39.107 kJ·mol^-1, respectively. The analyses on the combining interaction with the atom-in-molecules theory （AIM） also showed that a relatively strong lithium bond interaction presented in furan homologues C4H4Y-LiCH3 systems. Natural bond orbital theory （NBO） analysis has been performed, and the results revealed that the complex I is formed with n-σ type lithium bond interaction between C4H40 and LiCH3, complex II is formed with TT-s type lithium bond interaction between C4H4O and LiCH3, and complex III is formed with TT-s and n-s type lithium bond interactions between C4H4S and LiCH3, respectively.