Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

TFEL of Ce3+ in zine sulpho-oxide

A new TFEL material ZnS_xO_1−x: Ce³⁺ is prepared. The EL brightness of ZnS_xO_1−x: Ce³⁺ is at least one order higher than that of ZnS: Ce³⁺ at the same doping concentration of Ce³⁺. The EL emission wavelength of ZnS_xO_1−x: Ce³⁺ (X = 0.5) ranges from 400 to 600 nm. The emission of ZnS_xO_1−x: Ce³⁺ may be used as the blue part of white TFEL.     

Effect of austenitizing temperature on microstructure in 16Mn steel treated by cerium

The change of inclusions and microstructure of 16Mn steel treated by Ce were observed, and the effect of austenitizing temperature on the microstructure was also examined. The results show that the inclusions are transformed from Si-Mn-Al composite oxide and MnS into AlCeO₃, Ce₂O₂S, and MnS composite inclusions after being treated by Ce. Plenty of intragranular ferrites are formed in 16Mn steel containing ～0.017wt% Ce. A large amount of intragranular acicular ferrites are formed after being austenitized for 20 min at 1473 K. The prior austenite grain size fit for the formation of intragranular acicular ferrites is about 120 μm.     

Fabrication and morphology of NbCx-C composite three-dimensinal netted fibers

The raw materials were commercial powders of Nb₂O₅ (99.95%), reactive carbon (99.99%), NaCI (99.95%) and sucrose (99.94%). By the carbothermal method, the NbC_x (x= 0.98)-C composite three-dimensional netted fibers were prepared in graphite resistance furnace in 0.1 MPa/N₂ ambient atmosphere at temperature from 970 to 1 120°C. The diameters of composite three-dimensional netted fibers are 12–38 μm, the hole circumferences of netted fibers are 0.22–2.2 mm and the hole diameters are 70–701 μm. The process conditions for fabricating NbC_x-C composite three-dimensional netted fibers and related morphology, composition and crystal structure of NbC_x-C composite netted fibers were investigated in detail.     

Interface bond mechanisms of ceramic-cemented carbide compact insert

Conclusion Ceramic-cemented carbide compact inserts have been developed by hot-pressing sintering techniques, the upper part of the compact insert is of Al₂O₃ + TiB₂ ceramic material, while the base part of the compact insert is of WC + Co cemented carbide. The compact insert makes full use of the advantages of the high hardness of ceramic materials and the high strength of cemented carbide, and its mechanical properties are just between that of Al₂O₃ + TiB₂ and WC + Co. SEM, XRD and electron microprobe analysis showed that element diffusion and formation of new phases are the main causes for the bond of Al₂O₃ + TiB₂ with WC + Co in the interface.     

Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

原位合成CNTs/Cu-Al2O3复合材料的性能研究

对Al的质量分数分别为0.20%,0.35%,0.60%的Cu-Al合金粉末进行内氧化,得到Cu-Al₂O₃粉末。采用化学气相沉积法在Cu-Al₂O₃粉末表面原位生长碳纳米管(carbon nano tubes, CNTs),采用放电等离子烧结工艺成功制备了CNTs/Cu-Al₂O₃复合材料。采用扫描电子显微镜和透射电子显微镜观察了CNTs/Cu-Al₂O₃复合粉末、复合材料断口的形貌。采用显微硬度计、微拉伸试验机、摩擦磨损试验机分别对纯Cu及复合材料的维氏硬度、抗拉强度、摩擦因数进行测试。采用电化学工作站测试复合材料在3.5%NaCl (质量分数)水溶液中的耐腐蚀性能。结果表明,随着Al的质量分数的增加,粉末表面合成的CNTs的数量也增多。Al的质量分数为0.35%时,CNTs/Cu-Al₂O₃复合材料的综合性能最佳,与纯Cu相比,复合材料的抗拉强度和腐蚀电势分别提高了86.4%和43.2%,分别为315 MPa和-0.268 V,摩擦因数降低了53.3%,仅为0.28。     

烧结压力对Al90Mn9Ce1合金SPS致密化的影响

采用放电等离子烧结（SPS）技术,在50MPa,300MPa,600MPa单轴压力下,对固结气雾化法制备的粒度为20-45μm的Al90Mn9Ce1合金粉末,研究了压力和脉冲电流作用下的致密化过程。结果表明,提高烧结压力有助于粉末的塑性变形和幂率蠕变,促进Al90Mn9Ce1合金压坯的致密化。当烧结压力为600MPa时,在660K保温0min条件下,样品致密度达到99．2％,强度达到1048．5MPa,原始颗粒之间形成宽度为20nm的熔合区,界面结合良好。     

Mineralogical and sink-float studies of Jajarm low-grade bauxite

Jajarm’s bauxite deposits are mainly diasporic, and they have a low mass ratio of Al₂O₃/SiO₂. It is necessary to increase the run-of-mine mass ratio before feeding the material to the Bayer process. Chemical analysis indicated that the low-grade bauxite sample from Jajarm contained 43.9wt% Al₂O₃ and 13.35wt% SiO₂, resulting in a mass ratio of 3.29. According to mineralogical studies, the presence of aluminosilicate minerals such as kaolinite, illite, and quartz was the main reason for the decrease of the mass ratio. Microscopic observations revealed that, with the size reduction from -1000+710 to -38 μm, the liberation degree of diaspore increased from 10% to 60%, and that of aluminosilicates increased from 20% to 85%. Heavy liquids with the densities of 2.8, 3.0, 3.2, and 3.4 g/cm3 were used to evaluate the heavy media separation in three sizes, i.e., -3350+710, -710+212, and -212+125 μm. Laboratory studies confirm that the density of 3.2 g/cm3 can produce the concentrates (in sunk fractions) with recoveries of 89.09%, 91.24%, and 84.68% with the Al₂O₃/SiO₂ mass ratios of 5.03, 5.16, and 5.15 for the -3350+710, -710+212, and -212+125 μm sizes, respectively.     

Wear properties of NiAl based materials

The NiAl based materials including NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite were fabricated and their wear properties were tested at different temperatures.The results revealed that the NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite exhibited the excellent wear properties between 700℃ and 900℃.The microstructure observations exhibited that the self-lubricant films formed on the worn surfaces during the dry sliding test at high temperature,which decreased the wear rate and friction coefficient significantly.TEM observation on the self-lubricant film revealed that it was mainly comprised by ceramic amorphous and nanocrystalline.Compared with the NiAl-TiC-Al2O3 composite,the NiAl-Cr(Mo)-CrxSy in situ composite has lower friction coefficient at low temperature.Such phenomena may be ascribed to the addition of sulfide which contributes much to the formation of self-lubricant,and moreover the TiC addition increase the strength of NiAl based material and its wear resistance.     

Anti-penetration performance of high entropy alloy-ceramic gradient composites

A high-entropy alloy-ceramic gradient composite of TiC-TiB₂/75vol% Al_0.3CoCrFeNi was successfully prepared by combustion synthesis under an ultra-high gravity field, which is a low-cost method with high efficiency. The ceramic particles were gradient distributed in the Al_0.3CoCrFeNi matrix, and the hardness of the composite material gradually decreased along the thickness direction. The anti-penetration performance of the gradient composites was simulated using the ANSYS/LS-DYNA explicit simulation program. The results demonstrate that the distribution of the ceramic particles strongly affected the mechanical properties and the anti-penetration performance of the composites. With the same total ceramic volume fraction, the gradient composites exhibit better anti-penetration performance than the corresponding ceramic-metal interlayer composites. The more uneven the ceramic distribution, the greater the elastic modulus and yield stress of the surface layer and, thus, the better the anti-penetration performance.     

Electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.3</Subscript>Ti<Subscript>0.2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> cells

Spinel compounds LiNi_0.5Mn_1.3Ti_0.2O₄ (LNMTO) and Li₄Ti₅O₁₂ (LTO) were synthesized by different methods. The particle sizes of LNMTO and LTO are 0.5–2 and 0.5–0.8 μm, respectively. The LNMTO/LTO cell exhibits better electrochemical properties at both a low current rate of 0.2C and a high current rate of 1C. When the specific capacity was determined based on the mass of the LNMTO cathode, the LNMTO/LTO cell delivered 137 mA·h·g⁻¹ at 0.2C and 118.2 mA·h·g⁻¹ at 1C, and the corresponding capacity retentions after 30 cycles are 88.5% and 92.4%, respectively.     

The strain ampli tude-controlled cyclic fatigue behavior of Al2O3 fiber reinforced Al–Si alloy composite at elevated temperatures

The strain amplitude-controlled fatigue characteristics of an Al–Si casting alloy and itscomposite reinforced with 17 vol% Al₂O₃ fibers (Al–Si/Al₂O₃) are studied at three different temperatures. Both the alloy and the composite showed different degrees of cyclic softening at elevated temperatures. Increasing the temperature, fatigue damage of either the alloy or the composite occurred with varying mode from brittle fracture of silicon particles to their separation from the aluminum matrix. This is explained by the different thermal expansion coefficients of silicon particles and the aluminum matrix. The reinforcement Al₂O₃ fibers in the composite showed a similar damage behavior with those silicon particles despite temperature variation     

Synthesis of nonstoichiometric M-type barium ferrite nanobelt by spark plasma sintering method

This study investigated the feasibility of ultrafast crystallization of M-type barium ferrite when the coprecipitation precursors in stoichiometric proportions as BaFe12O19, Fe(OH)3 and BaCO3 nanoparticles, had been heated by spark plasma sintering (SPS) process. The results show that SPS method may realize the ultrafast crystallization of M-type barium ferrite, absolutely prevent the crystallization of intermediate phase α-Fe2O3, and significantly decrease the crystallization temperature of M-type barium ferrite. The sintered samples obtained at 800℃ by sintering the precursors for 10 minutes are a kind of multiphase ferrites composed of major phase M-type barium ferrite and trace amount of BaFe0.24Fe0.76O2.88. It is discovered that M-type barium ferrites in the holes of the sintered samples are in nanobelt microstructure about 100-300 nm in width and several micrometers in length. These M-type barium ferrite nanobelts are non-stoichiometric and may be expressed as BaFe12 xO19 1.5x (-4.77≤x≤6.50). Their composistions suggest completely random Fe-rich or Ba-rich domains.     

Optimum sintering conditions for optical properties of translucent aluminum nitride ceramics

High translucency is one of the excellent properties of AlN ceramics because of its wide optical band gap energy of 6.2 eV. We have achieved success in producing AlN ceramic tube of 98% total visible light transmittance at 0.6 mm thick tube wall by applying an improved sintering technique. This AlN ceramic was produced by sintering at 1880℃ using Ca3Al2O6 as a sintering additive and in reduction atmosphere to remove the sintering additive from the final sintered material. After the sintering, the annealing ...     

Effect of Ce addition on hot tearing behavior of AZ91 alloy

A small amount of cerium (below 1.0 wt%) addition to AZ91 alloy have been investigated on the hot tearing susceptibility (HTS) at a cooling rate of 1.5Ks^?1. The HTS increased to a maximum value with a cerium addition of 0.6 wt% and then decreased to a stable status as cerium was gradually added. Due to high chemical activity, cerium into the melts can react with aluminum to form an Al₁₁Ce₃ intermetallic compound. X–ray diffraction results also confirmed the existence of Al₁₁Ce₃. The Al₁₁Ce₃ increased with the presence of the needle-like and block morphology. As cerium levels increased, the amount of Mg₁₇Al₁₂ decreased. The variations between Mg₁₇Al₁₂ and Al₁₁Ce₃ resulted in a similar normal distribution of the HTS in AZ91 alloy. The findings were further verified through the microstructure evolution and the surface morphology of fracture.     

Mn_2O_3/CRF复合材料的制备及其在超级电容器中的应用

通过采用沉淀法在碳气凝胶表面负载金属氧化物三氧化二锰,制备得到Mn_2O_3/CRF复合材料。采用X射线衍射及电镜扫描等技术对所制备的复合材料进行结构形貌表征。实验结果发现碳气凝胶具有多重片层结构且孔隙发达。通过调节锰盐的含量考察三氧化二锰负载量对复合材料电化学性能的影响作用。采用循环伏安法及充放电测试对材料的电化学性能进行测试,结果表明Mn_2O_3/CRF复合材料具有良好的电容性及较好的可逆性。当Mn_2O_3含量达15%时复合材料的比电容最大,可达118.5 F/g。通过充放电测试1000次后发现该电极的比电容依然能够保持在一稳定值上,具有较好的稳定性。     

Sintering mechanism of Cu-9Al alloy prepared from elemental powders

The sintering behavior of Cu-9Al alloys prepared from die pressing of elemental powders was investigated. The experimental results and kinetic analysis showed the formation of three consecutive layers of Al₂Cu, Al₄Cu₉, and AlCu phases, with Al₂Cu appearing first in the initial solid phase sintering stage. A liquid phase formed in the intermediate stage, resulting from the eutectic reaction between Al and Al₂Cu phases at 500 °C, which is 47 °C lower than the equilibrium reaction temperature. Swelling occurred when the liquid phase infiltrated the gaps between the copper particles, leaving pores at the original sites of Al particles and Al₂Cu. In the final stage of sintering, the Al-rich phases (Al₂Cu and AlCu) transformed to Al-poor phases (Al₄Cu₉ and α-Cu) in the temperature range of 500–565 °C. Al₄Cu₉ and α-Cu then transformed to AlCu₃ (β) above the eutectoid reaction temperature (565 °C), whereas AlCu₃ transformed to α-Cu and eutectoid phases (α-Cu + Al₄Cu₉) during cooling. The pure copper transformed to AlCu₃, and the pore volume decreased at 1000 °C. The microstructure study helps manipulate precisely the sintering process of Cu-Al alloys and optimize the microstructure with a high dimensional accuracy.     

Interfacial behavior of Fe76Si9B10P5/Zn0.5Ni0.5Fe2O4 amorphous soft magnetic composite during spark plasma sintering process

Fe_(76)Si_9B_(10)P_5/Zn_(0.5)Ni_(0.5)Fe_2O_4 amorphous composite with micro-cellular structure and high electrical resistivity was prepared by spark plasma sintering(SPS) at 487 °C. XRD and SEM results showed that the Fe_(76)Si_9B_(10)P_5 alloy powders remained the amorphous state and the composite was dense. A fusion zone at interface of Fe_(76)Si_9B_(10)P_5 cell body and Zn_(0.5)Ni_(0.5)Fe_2O_4 cell wall was observed by TEM, which also indicates the formation of local high temperature. The interface bonding based on the formation of local high temperature in SPS process was observed. It is believed that the tip effect of Zn_(0.5)Ni_(0.5)Fe_2O_4 nanoparticles promotes the local discharging and plasmas creation in the gaps, and the discharging energy forms an instantaneous local high temperature to complete the local sintering and the densification of Zn_(0.5)Ni_(0.5)Fe_2O_4 particles at a low nominal sinter temperature. Simultaneously, the local high temperature stimulates the adjacent gaps discharging, thus facilitate the continuous formation of new discharging path. Finally, sintering and densification of the amorphous composite is complete.