高重力燃烧合成WC/CoCrFeNiAl0.2高熵合金复合材料

The WC/CoCrFeNiAl_0.2 high-entropy alloy (HEA) composites were prepared through high-gravity combustion synthesis. The preparation method is presented below. First, using a designed suitable multiphase thermite system, the molten CoCrFeNiAl_0.2 HEA was fabricated using low-cost metal oxides. The molten HEA was subsequently infiltrated into the WC layer to fabricate WC/CoCrFeNiAl_0.2 composites in a high-gravity field. The porosity of the WC/CoCrFeNiAl_0.2 composites was down-regulated, and their compressive yield strength was up-regulated when the high-gravity field was increased from 600gto 1500gbecause this infiltration process of a HEA melt into the WC layer is driven by centrifugal force. The WC particles in the composites exhibited a gradient distribution along the direction of the centrifugal force, which was attributed to the combined action of the high-gravity field and the temperature gradient field. The Vickers hardness of the sample was down-regulated from 9.53 to 7.41 GPa along the direction of the centrifugal force.     

Effect of Ti/B Additions on the Formation of Al3 Ti of in situ TiB2/Al Composites

A novel technique for fabricating TiB₂/Al composites in molten aluminum was introduced. The formation mechanism of brittle Al₃Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The results show that (1) the brittle Al₃Ti particulates are always present in the composites when the molar ratio of Ti to B n_Ti:n_B is 1:2; and (2) the formation of the brittle Al₃Ti phase can be avoided entirely from the final product by using a proper n_Ti:n_B of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the later case, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot of Al₃Ti (4%), whereas the ultimate tensile strength of the former is nearly that of the later.     

Fabrication of Fe–TiC–Al2O3 composites on the surface of steel using a TiO2–Al–C–Fe combustion reaction induced by gas tungsten arc cladding

The aim of the present study was to fabricate Fe–TiC–Al₂O₃ composites on the surface of medium carbon steel. For this purpose, TiO₂–3C and 3TiO₂–4Al–3C–xFe (0 ≤ x ≤ 4.6 by mole) mixtures were pre-placed on the surface of a medium carbon steel plate. The mixtures and substrate were then melted using a gas tungsten arc cladding process. The results show that the martensite forms in the layer produced by the TiO₂–3C mixture. However, ferrite–Fe₃C–TiC phases are the main phases in the microstructure of the clad layer produced by the 3TiO₂–4Al–3C mixture. The addition of Fe to the TiO₂–4Al–3C reactants with the content from 0 to 20wt% increases the volume fraction of particles, and a composite containing approximately 9vol% TiC and Al₂O₃ particles forms. This composite substantially improves the substrate hardness. The mechanism by which Fe particles enhance the TiC + Al₂O₃ volume fraction in the composite is determined.     

Surface composites fabricated by vacuum infiltration casting technique

Alumina (Al₂O₃) particles reinforced copper matrix surface composites were fabricated on the bronze substrate using the vacuum infiltration casting technique. Three cases were obtained in the vacuum infiltration casting technique: no infiltration, partial infiltration and full infiltration (the thickness of preforms do not exceed 3.5 mm). The reason of no infiltration is that the vacuum degree is not enough so that the force acting on the liquid metal is lower than the resistance due to the surface tension. Partial infiltration is because of somewhat lower vacuum degree and pouring temperature. Full desired infiltration is on account of suitable infiltration casting conditions, such as vacuum degree, pouring temperature, grain size and preheating temperature of the preform. The most important factor of affecting formation of surface composites is the vacuum degree, then pouring temperature and particle size. The infiltration mechanism was discussed on the bases of different processing conditions. The surface composite up to 3.5 mm in thickness with uniformly distributed Al₂O₃ particles could be fabricated via the vacuum infiltration casting technique.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3sf</Subscript> addition on the friction and wear properties of (SiC<Subscript>p</Subscript>+Al<Subscript>2</Subscript>O<Subscript>3sf</Subscript>)/Al2024 composites fabricated by pressure infiltration

Aluminum (Al) 2024 matrix composites reinforced with alumina short fibers (Al₂O_3sf) and silicon carbide particles (SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al₂O_3sf on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al₂O_3sf, characterized by the ratio of Al₂O_3sf to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al₂O_3sf to SiC_p was increased from 0 to 1, the rate of wear mass loss (K_m) and coefficients of friction (COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K_m increased rapidly and the wear mechanism became adhesive wear.     

Pseudo-<Emphasis Type="Italic">in-situ</Emphasis> stir casting: a new method for production of aluminum matrix composites with bimodal-sized B<Subscript>4</Subscript>C reinforcement

A new method was applied to produce an Al-0.5wt%Ti-0.3wt%Zr/5vol%B₄C composite via stir casting with the aim of characterizing the microstructure of the resulting composite. For the production of the composite, large B₄C particles (larger than 75 μm) with no pre-heating were added to the stirred melt. Reflected-light microscopy, X-ray diffraction, scanning electron microscopy, field-emission scanning electron microscopy, laser particle size analysis, and image analysis using the Clemex software were performed on the cast samples for microstructural analysis and phase detection. The results revealed that as a consequence of thermal shock, B₄C particle breakage occurred in the melt. The mechanism proposed for this phenomenon is that the exerted thermal shock in combination with the low thermal shock resistance of B₄C and large size of the added B₄C particles were the three key parameters responsible for B₄C particle breakage. This breakage introduced small particles with sizes less than 10 μm and with no contamination on their surfaces into the melt. The mean particle distance measured via image analysis was approximately 60 μm. The coefficient of variation index, which was used as a measure of particle distribution homogeneity, showed some variations, indicating a relatively homogeneous distribution.     

Novelty phase synthesis mechanism and morphology in resin-bonded Al-Al2O3-TiO2 composites at high temperatures under flowing N2

An Al-AlN core-shell structure is beneficial to the performance of Al-Al₂O₃ composites. In this paper, the phase evolution and microstructure of Al-Al₂O₃-TiO₂ composites at high temperatures in flowing N₂ were investigated after the Al-AlN core-shell structure was created at 853 K for 8 h. The results show that TiO₂ can convert Al into Al₃Ti (~1685 K), which reduces the content of metal Al and rearranges the structure of the composite. Under N₂ conditions, Al₃Ti is further transformed into a novelty non-oxide phase, TiCN. The transformation process can be expressed as follows:Al₃Ti reacts with C and other carbides (Al₄C₃ and Al₄O₄C) to form TiC_x (x < 1). As the firing temperature increases, Al₃Ti transforms into a liquid phase and produces Ti(g) and TiO(g). Finally, Ti(g) and TiO(g) are nitrided and solid-dissolved into the TiC_x crystals to form a TiCN solid solution.     

Bulk Al-Al3Zr composite prepared by mechanical alloying and hot extrusion for high-temperature applications

Bulk Al/Al₃Zr composite was prepared by a combination of mechanical alloying (MA) and hot extrusion processes. Elemental Al and Zr powders were milled for up to 10 h and heat treated at 600℃ for 1 h to form stable Al₃Zr. The prepared Al₃Zr powder was then mixed with the pure Al powder to produce an Al-Al₃Zr composite. The composite powder was finally consolidated by hot extrusion at 550℃. The mechanical properties of consolidated samples were evaluated by hardness and tension tests at room and elevated temperatures. The results show that annealing of the 10-h-milled powder at 600℃ for 1 h led to the formation of a stable Al₃Zr phase. Differential scanning calorimetry (DSC) results confirmed that the formation of Al₃Zr began with the nucleation of a metastable phase, which subsequently transformed to the stable tetragonal Al₃Zr structure. The tension yield strength of the Al-10wt%Al₃Zr composite was determined to be 103 MPa, which is approximately twice that for pure Al (53 MPa). The yield stress of the Al/Al₃Zr composite at 300℃ is just 10% lower than that at room temperature, which demonstrates the strong potential for the prepared composite to be used in high-temperature structural applications.     

Microstructure and corrosion behavior of Al<Subscript>3</Subscript>Ti/ADC12 composite modified with Sr

In this study, we investigated the effect of the addition of Sr (0wt%, 0.1wt%, 0.2wt%, and 0.3wt%) on the microstructure and corrosion behavior of Al₃Ti/ADC12 composite by optical microscopy, X-ray diffraction, scanning electron microscopy, and energy diffraction spectroscopy. The results reveal that the α-Al phases were nearly spherical and 40 μm in size and that the eutectic Si phases became round in the composite when the Sr content reached 0.2wt%. The Al₃Ti particles were distributed uniformly at the grain boundary. The results of the corrosion examination reveal that the Al₃Ti/ADC12 composite exhibited a minimum corrosion rate of 0.081 g·m–2·h–1 for an Sr content of 0.2wt%, which is two thirds of that of unmodified composite (0.134 g·m–2·h–1). This improved corrosion resistance was due to galvanic corrosion, which resulted from the low area ratio of the cathode to anode regions. This caused a low-density corrosion current in the composite, thereby yielding optimum corrosion resistance.     

<Emphasis Type="Italic">In situ</Emphasis> synthesis of TiC reinforced Cu<Subscript>47</Subscript>Ti<Subscript>34</Subscript>Zr<Subscript>11</Subscript>Ni<Subscript>8</Subscript> bulk metallic glass composites

In situ synthesized TiC particles and β-Ti dendrites reinforced Cu47Ti34Zr11Ni8 bulk metallic glass (BMG) composite ingots were prepared by the suction casting method.The ingots with diameters from 1 up to 4mm were successfully obtained. It was shown that introducing TiC micro-sized particles into the amorphous matrix did not disturb the glass forming ability (GFA) of the matrix,while the yield strength and ductility could be well improved.The phase constitution, microstructure and elements distribution in the composites were studied by OM, XRD, SEM and EDS.It was shown that the in situ synthesized TiC particles acting as heterogeneous nucleation sites promoted the precipitation of β-Ti dendrites, resulting in the formation of the TiC particles and β-Ti dendrites co-reinforced BMG composites. The compressive tests were employed to probe the yield strength and ductility of BMG composites.     

Growth characteristics of directionally solidified Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/YAG/ZrO<Subscript>2</Subscript> ternary hypereutectic <Emphasis Type="Italic">in situ</Emphasis> composites under ultra-high temperature gradient

Oxide eutectic ceramic in situ composites have attracted significant interest in the application of high-temperature structural materials because of their excellent high-temperature strength, oxidation and creep resistance, as well as outstanding microstructural stability. The directionally solidified ternary Al₂O₃/YAG/ZrO₂ hypereutectic in situ composite was successfully prepared by a laser zone remelting method, aiming to investigate the growth characteristic under ultra-high temperature gradient. The microstructures and phase composition of the as-solidified hypereutectic were characterized by using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The results show that the composite presents a typical hypereutectic lamellar microstructure consisting of fine Al₂O₃ and YAG phases, and the enriched ZrO₂ phases with smaller sizes are randomly distributed at the Al₂O₃/YAG interface and in Al₂O₃ phases. Laser power and scanning rate strongly affect the sample quality and microstructure characteristic. Additionally, coarse colony microstructures were also observed, and their formation and the effect of temperature gradient on the microstructure were discussed.     

The strain ampli tude-controlled cyclic fatigue behavior of Al2O3 fiber reinforced Al–Si alloy composite at elevated temperatures

The strain amplitude-controlled fatigue characteristics of an Al–Si casting alloy and itscomposite reinforced with 17 vol% Al₂O₃ fibers (Al–Si/Al₂O₃) are studied at three different temperatures. Both the alloy and the composite showed different degrees of cyclic softening at elevated temperatures. Increasing the temperature, fatigue damage of either the alloy or the composite occurred with varying mode from brittle fracture of silicon particles to their separation from the aluminum matrix. This is explained by the different thermal expansion coefficients of silicon particles and the aluminum matrix. The reinforcement Al₂O₃ fibers in the composite showed a similar damage behavior with those silicon particles despite temperature variation     

Synthesis,structure and mechanical properties of Zr-Cu-based bulk metallic glass composites

The unusual glass-forming ability (GFA) of the Zr₄₈Cu₃₆Ag₈Al₈ alloy and the high ductility of the Zr₄₈Cu₃₆Ag₈Al₈ metallic glass-matrix composites containing Ta powder were reported. The bulk metallic glass rod with a diameter of 25 mm was successfully synthesized using copper mold casting for the Zr₄₈Cu₃₆Ag₈Al₈ alloy. High GFA of this alloy was found to be related to a large supercooled liquid region and a quaternary eutectic point with low melting temperature. The bulk metallic glass matrix composites were prepared by introducing extra Ta particles into the Zr₄₈Cu₃₆Ag₈Al₈ melt. The composites consist of Ta particles homogenously distributed in the Zr₄₈Cu₃₆Al₈Ag₈ metallic glass matrix. The optimum content of Ta powder is 10at% for the composite with the highest plasticity, which shows a plastic strain of 31%.     

Al2O3-SiC纳米复合陶瓷的制备及其表征

以分析纯Al(NO₃)₃·9H₂O, (CH₂)₆N₄和粒径为30 nm的SiC粉末为原料, 采用溶胶-凝胶(sol-gel)方法制备干凝胶, 经煅烧合成Al₂O₃-SiC纳米陶瓷粉, 利用真空热压装置对粉末进行烧结. 通过X射线衍射(XRD)、 扫描电镜(SEM)和维氏硬度实验分析了不同SiC含量和不同烧结温度的Al₂O₃-SiC陶瓷样品的结构、 形貌、 晶粒尺寸和硬度, 并研究了其机理.     

Ti3SiC2代替石墨金属基自润滑材料研究进展

Ti₃SiC₂是一种新型的金属陶瓷材料,该材料兼具金属与陶瓷材料的双重性能,具有良好的导电性、导热性、加工性、耐腐蚀性与高温抗氧化性,同时该材料还具有超低的摩擦因数.基于其独特性能,大量科研工作开始投入到使用Ti₃SiC₂代替石墨制备金属基自润滑复合材料中.介绍了近年来石墨及以Ti₃SiC₂作为固体润滑颗粒制备的金属基自润滑复合材料的研究现状及进展.探讨了石墨和Ti₃SiC₂与金属界面结合问题,并对比两种复合材料的力学性能和摩擦学性能.最后指出以Ti₃SiC₂代替石墨制备金属基自润滑材料的可行性以及未来的发展方向.     

Wear properties of NiAl based materials

The NiAl based materials including NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite were fabricated and their wear properties were tested at different temperatures.The results revealed that the NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite exhibited the excellent wear properties between 700℃ and 900℃.The microstructure observations exhibited that the self-lubricant films formed on the worn surfaces during the dry sliding test at high temperature,which decreased the wear rate and friction coefficient significantly.TEM observation on the self-lubricant film revealed that it was mainly comprised by ceramic amorphous and nanocrystalline.Compared with the NiAl-TiC-Al2O3 composite,the NiAl-Cr(Mo)-CrxSy in situ composite has lower friction coefficient at low temperature.Such phenomena may be ascribed to the addition of sulfide which contributes much to the formation of self-lubricant,and moreover the TiC addition increase the strength of NiAl based material and its wear resistance.     

功能梯度复合靶冲击毁伤研究进展

综述了以金属复合靶板、陶瓷/金属复合靶板为代表的功能梯度复合靶在弹丸撞击作用下的抗侵彻性能、破坏模式和毁伤机理等的国内外研究现状。分理论研究、实验研究和数值模拟三方面,重点讨论了靶板材料、靶板层数、组合方式及弹头形状等因素对靶板抗侵彻性能的影响。同时,结合作者前期相关工作,指出了当前研究工作中存在的不足,并提出了有待进一步研究的问题。     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

In situ reaction mechanism of MgAlON in Al-Al2O3-MgO composites at 1700℃ under flowing N2

The Al-Al₂O₃-MgO composites with added aluminum contents of approximately 0wt%, 5wt%, and 10wt%, named as M₁, M₂, and M₃, respectively, were prepared at 1700℃ for 5 h under a flowing N₂ atmosphere using the reaction sintering method. After sintering, the Al-Al₂O₃-MgO composites were characterized and analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that specimen M₁ was composed of MgO and MgAl₂O₄. Compared with specimen M₁, specimens M₂ and M₃ possessed MgAlON, and its production increased with increasing aluminum addition. Under an N₂ atmosphere, MgO, Al₂O₃, and Al in the matrix of specimens M₂ and M₃ reacted to form MgAlON and AlN-polytypoids, which combined the particles and the matrix together and imparted the Al-Al₂O₃-MgO composites with a dense structure. The mechanism of MgAlON synthesis is described as follows. Under an N₂ atmosphere, the partial pressure of oxygen is quite low; thus, when the Al-Al₂O₃-MgO composites were soaked at 580℃ for an extended period, aluminum metal was transformed into AlN. With increasing temperature, Al₂O₃ diffused into AlN crystal lattices and formed AlN-polytypoids; however, MgO reacted with Al₂O₃ to form MgAl₂O₄. When the temperature was greater than (1640 ±10)℃, AlN diffused into Al₂O₃ and formed spinel-structured AlON. In situ MgAlON was acquired through a solid-solution reaction between AlON and MgAl₂O₄ at high temperatures because of their similar spinel structures.