Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Microstructure and electrolysis behavior of self-healing Cu-Ni-Fe composite inert anodes for aluminum electrowinning

The microstructure evolution and electrolysis behavior of (Cu₅₂Ni₃₀Fe₁₈)-xNiFe₂O₄ (x=40wt%, 50wt%, 60wt%, and 70wt%) composite inert anodes for aluminum electrowinning were studied. NiFe₂O₄ was synthesized by solid-state reaction at 950℃. The dense anode blocks were prepared by ball-milling followed by sintering under a N₂ atmosphere. The phase evolution of the anodes after sintering was determined by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The results indicate that a substitution reaction between Fe in the alloy phase and Ni in the oxide phase occurs during the sintering process. The samples were also examined as inert anodes for aluminum electrowinning in the low-temperature KF-NaF-AlF₃ molten electrolyte for 24 h. The cell voltage during electrolysis and the corrosion scale on the anodes were analyzed. The results confirm that the scale has a self-repairing function because of the synergistic reaction between the alloy phase with Fe added and the oxide phase. The estimated wear rate of the (Cu₅₂Ni₃₀Fe₁₈)-50NiFe₂O₄ composite anode is 2.02 cm·a-1.     

Reduction in secondary dendrite arm spacing in cast eutectic Al-Si piston alloys by cerium addition

The effects of Ce on the secondary dendrite arm spacing (SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis (CA CCTA). -The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, △T_S, and low solidification temperature, △T_S, whereas 0.1wt% Ce resulted in a fast solidification time, △ta-Al, of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index (Q) and ultimate tensile strength of (UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.     

Effects of applied potential on the stress corrosion cracking behavior of 7003 aluminum alloy in acid and alkaline chloride solutions

Potentiodynamic polarization tests and slow strain rate test (SSRT) in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) in acid and alkaline chloride solutions under various applied potentials (E_a). The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution (AD) at open-circuit potential (OCP) and is highly susceptible to hydrogen embrittlement (HE) at high negative E_a in the solutions with pH levels of 4 and 11. The susceptibility increases with negative shift in the potential when E_a is less than -1000 mV vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when E_a is equal to -1000 mV vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

Glass-forming ability,microhardness, corrosion resistance,and dealloying treatment of Mg60-xCu40Ndx alloy ribbons

The influence of Nd addition on the glass-forming ability (GFA), microhardness, and corrosion resistance of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25, at%) alloys were investigated by differential scanning calorimetry, Vickers-type hardness tests, and electrochemical methods. The results suggest that the GFA and microhardness of the amorphous alloys increase until the Nd content reaches 20at%. The corrosion potential and corrosion current density obtained from the Tafel curves indicate that the Mg₃₅Cu₄₀Nd₂₅ ternary alloy exhibits the best corrosion resistance among the investigated alloys. Notably, nanoporous copper (NPC) was synthesized through a single-step dealloying of Mg_60-xCu₄₀Nd_x (x=5, 10, 15, 20, and 25) ternary alloys in 0.04 mol·L-1 H₂SO₄ solution under free corrosion conditions. The influence of dealloying process parameters, such as dealloying time and temperature, on the microstructure of the ribbons was also studied using the surface diffusivity theory. The formation mechanism of dealloyed samples with a multilayered structure was also discussed.     

Multi-index analysis of the melting process of laterite metallized pellet

Herein, a multi-index analysis of the nickel content of an alloy, output rate of the alloy, nickel recovery rate, and iron recovery rate during the melting of laterite metallized pellets was performed. The thermodynamic reduction behavior of oxides such as NiO, FeO, Fe₃O₄, and Cr₂O₃ was studied using the FactSage software, which revealed that SiO₂ is not conducive to the reduction of iron oxides, whereas the addition of basic oxides such as CaO and MgO is beneficial for the reduction of iron oxides. On the basis of a comprehensive analysis to achieve greater nickel recovery and lower iron recovery rates, the optimum experimental parameters in the orthogonal experiment were A3B1C3 (t=30 min, C/O=0.4, R=1.2); the indicators w_Ni, φ_alloy, η_Ni, and η_Fe had values of 15.0wt%, 12.1%, 44.9%, and 96.4%, respectively. In single-factor experiments, increasing basicity (R) substantially improved the separation effect in the low-basicity range 0.5 ≤ R ≤ 0.8 but not in the high-basicity range 0.8 ≤ R ≤ 1.2. Similar results were obtained for the effect of the C/O ratio. Moreover, the recovery rate of nickel increased with increasing recovery rate of iron.     

硼稀土共渗钛合金的耐蚀性研究

采用不需保护性气氛的固体粉末法对Ti6Al4V(TC4)合金表面进行稀土与硼共渗,并对硼稀土共渗TC4钛合金、单渗硼TC4钛合金及未经渗硼处理的TC4钛合金基体,分别在35%NaCl和5%H2SO4(质量分数)溶液介质中进行了腐蚀实验.X射线衍射分析表明,TC4表面渗层由TiB2和TiB组成.扫描电镜观察表明,外层的TiB2具有平坦的生长前沿,而内层TiB为锯齿状形貌;其中外层的TiB2内部存在少量针孔,分析认为是Ce原子与B原子共渗时产生的Kirkendall效应所致.Tafel极化曲线分析结果表明,在35%NaCl和5%H2SO4溶液介质中,各样品的耐蚀性大小排序为单渗硼TC4钛合金>硼稀土共渗TC4钛合金>未经渗硼处理的TC4钛合金.     

Effects of HNO3 concentration on the pit morphologies of aluminum foil etched in HNO3–HCl and HNO3–H2SO4–HCl solutions

In this work, the effects of HNO₃ concentration on the pit morphologies of high-cubic-texture aluminum foil etched in HNO₃–HCl and HNO₃–H₂SO₄–HCl solutions were investigated. When the aluminum foil was etched in HNO₃–HCl solutions, the morphologies of pits transformed from irregular tunnels to typical tunnels (as inverted pyramids) and shallow cuboids as the HNO₃ concentration in the etchant solution was increased. However, as the HCl concentration in the etchant solution was increased, the morphologies of pits transformed from shallow cuboids to typical tunnels (as inverted pyramids) and irregular tunnels. When the aluminum foil was etched in n N HNO₃–(7.2?n) N H₂SO₄–0.8 N HCl solutions, the morphologies of the pits transformed from typical tunnels (i.e., the number of sub-tunnels formed on the main tunnels increased) to irregular tunnels (corrugated tunnels and polyline tunnels) as the HNO₃ concentration in the etchant solution was increased. These effects are attributed primarily to corrosion on the (100) and (010) faces of pits being accelerated and to the (001) faces being prone to passivation to different degrees when various concentrations of HNO₃ are added to the etchant solutions.     

Influence of growth conditions on the electrochemical synthesis of SnS thin films and their optical properties

Tin sulfide (SnS) thin films were prepared by electrodeposition onto fluorine-doped tin oxide (FTO) glass substrates using an aqueous solution containing SnCl₂ and Na₂S₂O₃ at various deposition potentials (E) and bath concentrations. The pH value and temperature of the solution were kept constant. The deposited films were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), photoluminescence (PL), and ultraviolet–visible (UV–Vis) spectroscopy. The FESEM images demonstrated that changes in the deposition potential (E) and solution concentration led to marked changes in the morphology of the deposited SnS films. Energy-dispersive X-ray analysis (EDXA) results showed that the Sn/S atomic ratio strongly depended on both the solution concentration and the deposition potential. To obtain an Sn/S atomic ratio approximately equal to 1, the optimal Sn2+/S₂O₃2- molar ratio and E parameter were 1/8 and -1.0 V, respectively. The XRD patterns showed that the synthesized SnS was obviously polycrystalline, with an orthorhombic structure. The effects of the variations of bath concentration and deposition potential on the band-gap energy (E_g) were studied using PL and UV–Vis experiments. The PL spectra of all the SnS films contained two peaks in the visible region and one peak in the infrared (IR) region. The UV–Vis spectra showed that the optical band-gap energy varies from 1.21 to 1.44 eV.     

新型可焊6005A铝合金的腐蚀行为

采用电化学交流阻抗谱,极化曲线以及浸泡腐蚀实验研究了Cu含量变化对高速列车用6005A铝合金电化学腐蚀行为的影响.结果表明:在商用6005A铝合金基体中添加适量的Cu元素,可有效提高氧化膜的致密性.当添加Cu质量分数为0.4%时,轧制态6005A铝合金电化学交流阻抗图谱中腐蚀反应电阻Rct值较大,双电层电容Q2值较小,极化曲线出现了较宽电位范围的阳极钝化区.但合金自腐蚀电流小幅增加,显示合金局部耐蚀性下降.在质量分数为3.5%NaCl溶液中进行的浸泡实验显示,随着浸泡时间的延长,自制6005A铝合金依次发生点蚀、晶间腐蚀和剥蚀.合金表面氧化膜致密性是影响材料抗腐蚀能力的主要因素.     

Temperature effect on the corrosion and passivation characterization of Ni<Subscript>82.3</Subscript>Cr<Subscript>7</Subscript>Fe<Subscript>3</Subscript>Si<Subscript>4.5</Subscript>B<Subscript>3.2</Subscript> alloy in acidic media

The effects of temperature on corrosion and the electrochemical behavior of Ni_82.3Cr₇Fe₃Si_4.5B_3.2 glassy alloy in HCl, H₂SO₄, and H₃PO₄ acids were studied using AC and DC techniques. Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature. Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H₂SO₄ and H₃PO₄ solutions. A localized corrosion effect in HCl solution is clearly observed. The apparent activation energies in the regions of Tafel, active, and passive, as well as the enthalpies and entropies of the dissolution process were determined and discussed. The high apparent activation energy (E_a) value for H₃PO₄ solution in Tafel region is explained by the low aggressivity of PO₄3- ions.     

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

Novel ceramics from waste material made of (x) paper ash-(80-x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO₃), along with minor phases of γ-dicalcium silicate (Ca₂SiO₄) and quartz (SiO₂). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.>     

Vertex disjoint cycles in intersection graphs of bases of matroids

The intersection graph of bases of a matroid M=(E, B) is a graph G=G~I(M) with vertex set V(G) and edge set E(G) such that V(G)=B(M) and E(G)={BB′:|B∩B′|≠0, B, B′∈B(M), where the same notation is used for the vertices of G and the bases of M. Suppose that|V(G~I(M))| =n and k_1+k_2+…+k_p=n, where k_i is an integer, i=1, 2,…, p. In this paper, we prove that there is a partition of V(G~I(M)) into p parts V_1 , V_2,…, V_p such that |V_i| =k_i and the subgraph H_i induced by V_i contains a k_i-cycle when k_i ≥3, H_i is isomorphic to K_2 when k_i =2 and H_i is a single point when k_i =1.     

Gracefulness of several unconnected graphs with wheel

In the paper, we study the gracefulness of several unconnected graphs related to wheel. For natural number p ≥1,t ≥1, let n =2t +3, 2t +4, which proved W_n∪K_(p,t)~(1)∪K_(p,t)~(2) is graceful; for p ≥1, t ≥1,let n=2t+3,2t+4, then W_(n,2n+1)∪K_(p,t)~(1)∪K_(p,t)~(2) is graceful and for m≥1,r ≥1, let n =2m +5, W_(n,2n+1) ∪( C_3∨K m) U St( r)is graceful.     

Inter-phase selective corrosion of γ-TiAl alloy in molten salt environment at high temperature

Hot corrosion behavior of Ti-48Al-2Cr-2Nb alloy in molten salt environment of 75%Na_2SO_4 and 25%NaCl(mass fraction) at 800℃was studied using oxidation kinetics analysis,scanning electron microscopy,X-ray energy dispersive and X-ray diffraction analyses.The inter-phase selective corrosion,which caused the corrosion pits initiated from lamellar interfaces and the preferential corrosion ofα_2 phases,was observed during the hot corrosion of the alloy.The common controls of thermodynamic and kinetics in corr...     

Binding number,minimum degree and bipancyclism in bipartite graphs

Let G =(V_1,V_2,E) be a balanced bipartite graph with2 n vertices.The bipartite binding number of G,denoted by B(G),is defined to be n if G =K_n and min i∈{1,2}|N(S)|n min |N(S)|/|S|otherwise.We call G bipancyclic if it contains a cycle of every even length m for 4 ≤ m ≤ 2n.A theorem showed that if G is a balanced bipartite graph with 2n vertices,B(G) 3 / 2 and n 139,then G is bipancyclic.This paper generalizes the conclusion as follows:Let 0 c 3 / 2 and G be a 2-colmected balanced bipartite graph with 2n(n is large enough) vertices such that B(G) c and δ(G)(2-c)n/(3-c)+2/3.Then G is bipancyclic.     

Properties of a class of groups on <Emphasis Type="Italic">Z</Emphasis><Subscript><Emphasis Type="Italic">m</Emphasis></Subscript>

In this paper, we obtain the factorization of direct production and order of group GL(n, Z _m ) in a simple method. Then we generalize some properties of GL(2, Z _p ) proposed by Huppert, and prove that the group \(GL\left( {2,{Z_{{z^\lambda }}}} \right)\) is solvable. We also prove that group GL(n, Z _p ) is solvable if and only if GL(n, Z _p ) is solvable, and list the generators of groups GL(n, Z _p ) and SL(n, Z _p ). At last, we prove that PSL(2, Z _p )(p > 3) and PSL(n, Z _p )(n > 3) are simple.     

Corrosion behavior of Mg–Y alloy in NaCl aqueous solution

The corrosion behavior of Mg–(0.25, 2.5, 5, 8 and 15)Y alloys in 3.5wt.% NaCl aqueous solution was investigated. It was found that the degree of corrosion deterioration increased with increasing immersion time up to 2 h. Corrosion modes for the alloys with low and high content of Y element were general corrosion and pitting corrosion, respective ly, and the threshold content for the corrosion mode change was 2.5% for the tested alloys. The experimental results showed that the addition of Y refined the grain of the alloy, and the distribution, i.e., continuous or not, of the Mg24Y5 phases had great effect on the corrosion rate and corrosion mode.     

Anodic dissolution of a crack tip at AA2024-T351 in 3.5wt% NaCl solution

The anodic dissolution process of a crack tip at 2024-T351 aluminium alloy (AA2024-T351) was determined by means of scanning Kelvin probe (SKP). Wedge-open loading (WOL) specimens were immersed in a 3.5wt% NaCl solution. After various durations of immersion, the Volta potential distributions around the crack were measured by SKP and the surface morphologies were observed by scanning electron microscopy (SEM). It is found that there is a nonuniform distribution of Volta potential around the crack. Before immersion, the Volta potential at crack tip is more negative than that in other regions. However, after immersion, a converse result occurs with the most positive Volta potential measured at the crack tip. SEM observations demonstrate that the noticeable positive shift of Volta potential results from the formation of corrosion products which deposit around the crack tip. Energy-dispersive spectrometry (EDS) analysis shows that the corrosion products are mainly Al oxide and Cu-rich particles. These observations implicate that the applied stress contributes to the preferential anodic dissolution of the crack tip and the redistribution of Cu.