Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl(x=1, 3 and 5) alloys

As-extruded Mg–5Sn–1Zn–xAl alloys(x=1, 3, and 5) were fabricated by hot extrusion. The experimental results revealed that the yield strength of alloys initially decreased and then increased with the increase of Al content. These changes were mainly attributed to the difference in crystallographic texture and volume fractions of second phases. The ultimate tensile strength, yield strength, and elongation of the alloys were greater than 310 MPa, 227 MPa, and 11%, respectively. The strain hardening ability of the alloys was also discussed.     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Effects of Zn content on the microstructure and the mechanical and corrosion properties of as-cast low-alloyed Mg–Zn–Ca alloys

The effects of Zn content on the microstructure and the mechanical and corrosion properties of as-cast low-alloyed Mg–xZn–0.2Ca alloys (x=0.6wt%, 2.0wt%, 2.5wt%, hereafter denoted as 0.6Zn, 2.0Zn, and 2.5Zn alloys, respectively) are investigated. The results show that the Zn content not only influences grain refinement but also induces different phase precipitation behaviors. The as-cast microstructure of the 0.6Zn alloy is composed of α-Mg, Mg₂Ca, and Ca₂Mg₆Zn₃ phases, whereas 2.0Zn and 2.5Zn alloys only contain α-Mg and Ca₂Mg₆Zn₃ phases, as revealed by X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses. Moreover, with increasing Zn content, both the ultimate tensile strength (UTS) and the elongation to fracture first increase and then decrease. Among the three investigated alloys, the largest UTS (178 MPa) and the highest elongation to fracture (6.5%) are obtained for the 2.0Zn alloy. In addition, the corrosion rate increases with increasing Zn content. This paper provides an updated investigation of the alloy composition–microstructure–property relationships of different Zn-containing Mg–Zn–Ca alloys.     

Mechanical behaviors of extruded Mg alloys with high Gd and Nd content

The influence of alloying elements and heat treatment on the microstructure and mechanical behaviors of extruded Mg–Gd–Nd ternary alloys was investigated in this study. The grain sizes dramatically decreased after extrusion, and the particles which distributed in Mg matrix had great effect on the grain size. The grain sizes of extruded alloys decreased from 26 to 5 μm with the alloying content increasing. The mechanical test results show that both Gd and Nd had positive effect on the hardness, y...     

Effects of Gd solutes on hardness and yield strength of Mg alloys

Relative contribution of individual strengthening mechanisms to the yield strength of Mg–0–15 wt%Gd alloys were investigated.Alloys with different grain size were prepared by adding Zr and hot extrusion.Hardness and tensile/compression yield strength were tested on the alloys after solid solution treatment and extrusion.HallPetch constants were calculated with hardness and tensile/compressive data.The results showed that the hardness of Mg–Gd alloys with similar Gd content and different grain size were almost the same,which indicates that grain size had little effect on hardness.The hardness linearly increased with rising Gd content(d H_v/dc≈25 kg mm~(-2)/at%Gd).The tensile and compressive yield strengths enhanced with the increase of Gd content for all alloys in different conditions.In addition,the tensile/compressive(t/c)yield asymmetry of extruded alloys decreased with increasing Gd content.Large t/c yield asymmetry ratio(1.77)was observed for pure Mg,and with increasing Gd content this value decreased to 1.With the increasing of tensile strength,the stress intensity factor,k_y,decreased from 0.27 MPa m~(1/2)for Mg–2 wt%Gd alloy to 0.19 MPa m~(1/2) for Mg–5 wt%Gd alloy,then increased to 0.29 MPa m~(1/2) for Mg–15 wt%Gd alloy.However,k_yincreased linearly form 0.16–0.31 MPa for compression test.The influence of grain size strengthening was eliminated,and the yield strength of tension and compression both linearly increased with c~n,where c is the atom concentration of Gd,and n=1/2 or 2/3.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of alloying elements and processing parameters on the Portevin–Le Chatelier effect of Al–Mg alloys

The effects of alloying elements and processing parameters on the mechanical properties and Portevin–Le Chatelier effect of Al–Mg alloys developed for inner auto body sheets were investigated in detail. Tensile testing was performed in various Zn and Mg contents under different annealing and cold-rolling conditions. In the results, the stress drop and reloading time of serrations increase with increasing plastic strain and exhibit a common linear relationship. The increase rates of stress drop and reloading time increase with increasing Mg or Zn content. The alloys with a greater intensity of serrated yielding generally exhibit a greater elongation. The stress drop and reloading time of serrations decrease with increasing grain size in the case of the annealed samples. The cold-rolled sample exhibits the most severe serration because it initially contains a large number of grain boundaries and dislocations.     

In vitro corrosion behavior of the extruded Mg–4Zn–1Mn alloy in different physiological solutions for biomedical applications

The extruded Mg–4Zn–1Mn alloy was prepared and its in vitro corrosion behavior in different physiological solutions of simulated body fluid(SBF), artificial saliva(AS) and artificial urine(AU) was investigated for biomedical applications. The microstructural characterization by optical microscope(OM), X-ray diffractometer(XRD), scanning electron microscopy(SEM) and energy dispersive X-ray spectrometer(EDS) showed that the alloy with an average grain size of approximate 20 μm was mainly composed ...     

Effects of aging on the microstructures and mechanical properties of extruded AM50 ＋ xCa magnesium alloys

The effects of aging treatment on the microstructures and mechanical properties of extruded AM50 ＋ xCa alloys （x = 0. 1%, 2% in mass fraction） were studied. The results indicated the secondary phase Mg17Al12 precipitated from the saturated a-Mg solid solution while Al2Ca changed slightly when the aging time was increased. The hardness of extruded AM50 ＋ xCa alloys increased initially to its peak, and then dropped to reach its original hardness with the increase in aging time.     

Ameliorating mechanical properties and reducing anisotropy of as-extruded Mg-1.0Sn-0.5Ca alloy via Al addition

Effects of Al addition to a Mg–Sn–Ca ternary alloy on its microstructure and tensile properties after extrusion were studied via extrusion of Mg-1.0 Sn-0.5 Ca-x Al(x = 0, 0.8, 2.4 wt%) sheets and analysis of the extruded materials.The results showed that Al addition not only refined the grain size(from 9.8 ± 0.7 μm to 8.3 ± 0.4 μm and7.6 ± 0.5 μm) but also accelerated the generation of more second phase(from 0.98 to 1.72 and 4.32%). Except for the CaMgSn and Mg₂Ca in Mg-1.0Sn-0.5 Ca a...     

In vitro corrosion of Mg–1.21Li –1.12Ca –1Y alloy

The influence of the microstructure on mechanical properties and corrosion behavior of the Mg–1.21Li–1.12Ca–1Y alloy was investigated using OM, SEM, XRD, EPMA, EDS, tensile tests and corrosion measurements. The results demonstrated that the microstructure of the Mg–1.21Li–1.12Ca–1Y alloy was characterized by α-Mg substrate and intermetallic compounds Mg2 Ca and Mg24Y5. Most of the fine Mg2 Ca particles for the as-cast alloy were distributed along the grain boundaries, while for the as-extruded along the extrusion direction. The Mg24Y5 particles with a larger size than the Mg2 Ca particles were positioned inside the grains. The mechanical properties of Mg–1.21Li–1.12Ca–1Y alloy were improved by the grain refinement and dispersion strengthening. Corrosion pits initiated at the α-Mg matrix neighboring the Mg2 Ca particles and subsequently the alloy exhibited general corrosion and filiform corrosion as the corrosion product layer of Mg(OH)2and Mg CO3 became compact and thick.     

Effect of Zn addition on microstructure and mechanical properties of an Al–Mg–Si alloy

In the present work, an Al–0.66Mg–0.85Si–0.2Cu alloy with Zn addition was investigated by electron back scattering diffraction(EBSD), high resolution electron microscopy(HREM), tensile and Erichsen tests. The mechanical properties of the alloy after pre-aging met the standards of sheet forming. After paint baking, the yield strength of the alloy was improved apparently. GP(Ⅱ) zones and η’phases were formed during aging process due to Zn addition. With the precipitation of GP zones, β″ phases, GP(Ⅱ) zones and η’phases, the alloys displayed excellent mechanical properties.     

Developing Mg–Zn surface alloy by friction surface allosying: In vitro degradation studies in simulated body fluids

A new variant of friction-assisted process named friction surface alloying(FSA) for developing surface alloys was demonstrated in the present work. In FSA, the dispersed phase is melted and allowed to react with the matrix material to form an alloy at the surface of a metallic substrate. In the present work, magnesium(Mg) sheets and zinc(Zn) powder were selected, and fine grained(～3.5 μm) Mg–Zn surface alloy with improved hardness was produced by FSA. X-ray diffraction studies confirmed the formation of intermetallic phases of Mg and Zn at the surface. From the in vitro degradation studies carried out by immersing in simulated body fluids, a lower corrosion rate was observed for the Mg–Zn surface alloy compared with pure Mg. The surface morphologies after immersion studies indicated large degraded areas on the base Mg compared with Mg–Zn. The results demonstrate the potential of FSA in developing Mg-based surface alloys without melting the substrate to impart better surface properties.     

摩擦表面合金化法开发一种 Mg–Zn 表面合金:模拟体液中的体外降解研究

A new variant of friction-assisted process named friction surface alloying (FSA) for developing surface alloys was demonstrated in the present work. In FSA, the dispersed phase is melted and allowed to react with the matrix material to form an alloy at the surface of a metallic substrate. In the present work, magnesium (Mg) sheets and zinc (Zn) powder were selected, and fine grained (~3.5 μm) Mg–Zn surface alloy with improved hardness was produced by FSA. X-ray diffraction studies confirmed the formation of intermetallic phases of Mg and Zn at the surface. From the in vitro degradation studies carried out by immersing in simulated body fluids, a lower corrosion rate was observed for the Mg–Zn surface alloy compared with pure Mg. The surface morphologies after immersion studies indicated large degraded areas on the base Mg compared with Mg–Zn. The results demonstrate the potential of FSA in developing Mg-based surface alloys without melting the substrate to impart better surface properties.     

Microstructure,mechanical, and corrosion properties of extruded low-alloyed Mg–xZn–0.2Ca alloys

The microstructure, mechanical, and corrosion properties of extruded low-alloyed Mg-xZn-0.2Ca (x=0, 1.0, 2.0, 3.0) alloys were investigated in this study. Findings from scanning electron microscope, X-ray diffraction and transmission electron microscopy results indicate that the amount of ternary Ca₂Mg₆Zn₃ phase, as the only secondary phase in 1.0Zn, 2.0Zn, and 3.0Zn alloys, gradually increases with the addition of Zn, while the Mg₂Ca phase was observed in the Mg-0.2Ca alloy only. Zn has a strong effect on the orientation and intensity of textures, which also influence mechanical behaviors, as revealed by electron back-scatter diffraction. Among all the alloys, the Mg-2.0Zn-0.2Ca alloy obtains the maximum tensile strength (278 MPa) and yield strength (230 MPa). Moreover, Zn addition has an evident influence on the corrosion properties of Mg-xZn-0.2Ca alloy, and Mg-1.0Zn-0.2Ca alloy exhibits the minimum corrosion rate. This paper provides a novel low-alloyed magnesium alloy as a potential biodegradable material.     

Effects of icosahedral phase formation on the microstructure and mechanical improvement of Mg alloys: A review

Icosahedral phase (I-phase) is a relatively excellent strengthening phase in Mg alloys. Depending on their volume fraction, the yield strength of Mg–Zn–Y–Zr alloys can vary from 150 to 450 MPa at room temperature. Recently, the formation of I-phase has been considered as one of the most effective methods for developing high strength lightweight Mg alloys for automotive and aerospace applications. In this review article, a series of research work about I-phase containing Mg alloys have been systematically investigated including I-phase formation mechanism and their effects on mechanical properties of Mg alloys. Particular emphases have been given to: (1) Structure of I-phase and its orientation relationship with the a-Mg matrix. (2) Influence of alloying elements and solidification conditions on I-phase formation. (3) Effects of I-phase on microstructural evolution and mechanical improvement of Mg–Zn–Y–(Zr) alloys. Moreover, the applications of I-phase for the mechanical improvement of other Mg alloys such as AZ91 and super-lightweight Mg–Li alloys are also reviewed.     

Microstructure and mechanical properties of the micrograined hypoeutectic Zn–Mg alloy

A biodegradable Zn alloy, Zn–1.6Mg, with the potential medical applications as a promising coating material for steel components was studied in this work. The alloy was prepared by three different procedures: gravity casting, hot extrusion, and a combination of rapid solidification and hot extrusion. The samples prepared were characterized by light microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction analysis. Vickers hardness, tensile, and compressive tests were performed to determine the samples’ mechanical properties. Structural examination reveals that the average grain sizes of samples prepared by gravity casting, hot extrusion, and rapid solidification followed by hot extrusion are 35.0, 9.7, and 2.1 μm, respectively. The micrograined sample with the finest grain size exhibits the highest hardness (Hv = 122 MPa), compressive yield strength (382 MPa), tensile yield strength (332 MPa), ultimate tensile strength (370 MPa), and elongation (9%). This sample also demonstrates the lowest work hardening in tension and temporary softening in compression among the prepared samples. The mechanical behavior of the samples is discussed in relation to the structural characteristics, Hall–Petch relationship, and deformation mechanisms in fine-grained hexagonal-close-packed metals.     

Effect of homogenization process on the hardness of Zn–Al–Cu alloys

The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell “B” hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of the θ and τ' phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and temperature, used in their preparation.