Application of upconversion luminescence in dye-sensitized solar cells

An upconversion luminescence powder TiO2:(Er3+,Yb3+) is prepared by a hydrothermal method and used to fabricate dye-sensitized solar cell (DSSC).The TiO2:(Er3+,Yb3+) powder undergoes upconversion luminescence,converting infrared light which the dye can not absorb into visible light with wavelengths of 510-700 nm which the dye can absorb,increasing the photocurrent of the DSSC.TiO2:(Er3+,Yb3+) also acts as a p-type dopant,heightening the Fermi level of the oxide film,which increases the photovoltage of the DSSC.The best performance of the DSSC is found when the ratio of TiO2/luminescence powder is 1/3 in the luminescence layer.Under simulated solar irradiation of 100 mW cm-2 (AM 1.5),the DSSC containing TiO2:(Er3+,Yb3+) doping achieves a light-to-electricity energy conversion efficiency of 7.28% compared with 6.41% for the undoped DSSC.     

Y2O2S:Eu3+,Zn2+,Ti4+荧光体的缺陷及红色长余辉发光性质

采用高温固相法合成了红色长余辉材料Y2O2S:Eu3+,Zn2+,Ti4+,实现了余辉发光中心和缺陷中心之间的能量传递。通过XRD、荧光发射和激发光谱、余辉发射光谱与衰减曲线、色坐标和热释光谱测试手段对Y2O2S:Eu3+,Zn2+、Y2O2S:Eu3+,Ti4+、Y2O2S:Eu3+,Zn2+,Ti4+和Y2O2S:Eu3+,Mg2+,Ti4+进行了结构与性能的表征,发现其荧光发射与余辉发射基本一致,红色余辉发光主峰位于625 nm附近,来源于Eu3+的5D0→7F2跃迁发射。相比而言,Y2O2S:Eu3+,Zn2+,Ti4+余辉发光性能最好,可持续1.5 h左右。     

Synthesis and luminescence properties of Eu3+, Sm3+ doped (YxGd1-x)2O3:Si4+, Mg2+ long-lasting phosphor

A novel red long-lasting phosphor, (Y_1−x Gd _x )₂O₃:Eu³⁺, Sm³⁺, Si⁴⁺, Mg²⁺, was synthesized by the co-precipitation method using oxalate precipitation as the precursor. X-ray diffraction (XRD), scanning electronic microscopy (SEM), integrated thermal analyzer (TG), and photoluminescence spectra (PL) as well as the ST-900PM weak light photometer were used to study the synthesis conditions, morphology, luminescence properties, and the decay time of the phosphor. The XRD results show that the products synthesized at 1400°C for 4 h have good crystallization without any detectable impurity phases. Based on the PL spectra, the optimal conditions are as the following. The molar ratios of Y³⁺ to Gd³⁺ and Eu³⁺ to Sm³⁺ are 2:8 and 3:1, respectively, and the contents of Mg²⁺ and SiO₂ are 5mol% and 3mol%, respectively. The decay time monitored by the ST-900PM weak light photometer is 7200 s, increasing 44% and 100%, respectively, compared with the Eu³⁺ and Sm³⁺ single-doped phosphors. The results indicate that the energy transfer is from Sm³⁺ to Eu³⁺ ion, and Sm³⁺ is a good sensitizer to Eu³⁺.     

Down-conversion characteristics of Eu3+ doped M2Y2Si2O9 (M = Ba,Ca, Mg and Sr) nanomaterials for innovative solar panels

Down-conversion properties of Eu³⁺ doped M₂Y₂Si₂O₉ (M = Ba, Ca, Mg, Sr) phosphors have been investigated in detail. These phosphors were synthesized via the simple, fast and cost-effective sol-gel technique at a temperature of 950 °C. Color coordinates and emission color can be altered by the varying concentration of dopant ion in Ca₂Y₂Si₂O₉ phosphor. Optimum luminescence intensity was obtained when doping 0.03 mol of Eu³⁺ ion. Using the excitation wavelength of 395 nm, these silicates showed strong red color, pure and sharp spectral peaks in visible region due to ⁵D₀→⁷F_1-3 transitions of Eu³⁺ present in the lattice. Effect of reaction temperature on luminescence was also analyzed for these phosphors. The sharp peaks in the X-ray diffraction pattern indicated the high crystallinity of prepared phosphors. Ca₂Y₂Si₂O₉ has shown an orthorhombic crystal structure. The FTIR results confirmed the metal-oxygen vibrational modes available in the range of 400–1600 cm^?1. Transmission electron microscopy images have revealed that the variation of alkaline earth metal provided a very different crystal structure. Excellent down conversion response of these phosphor materials can provide a great significance in the application of the coming solar devices.     

Structural investigation and luminescent properties of BaZr(BO<Subscript>3</Subscript>)2:Eu<Superscript>3+</Superscript> phosphors containing Si

Si⁴⁺-doped BaZr(BO₃)₂:Eu³⁺ phosphors are prepared by a conventional solid-state reaction. The influence of Si⁴⁺ addition on the charge transfer state of Eu³⁺-O^2– and photoluminescence (PL) properties of BaZr(BO₃)₂:Eu³⁺ are discussed. Room temperature PL spectra indicated that efficient emission is obtained by Si doping. Increased values for the peak-peak ratio (PPR) of BaZr(BO₃)₂:Eu³⁺ at higher Si doping concentrations implied that the Eu³⁺ ion is located in a more asymmetric environment in BaZr_0.8Si_0.2(BO₃)₂:Eu³⁺ than in the undoped samples. The Judd-Ofelt parameters Ω_λ (λ=2,4) were calculated from the PL data, giving results that were consistent with those from the PPR. The maximum radiative quantum efficiency was achieved at a Si doping concentration of 20 mol%.     

Potential red-emitting phosphor GdNbO4:Eu3+,Bi3+ for near-UV white light emitting diodes

A red-emitting phosphor GdNbO₄:Eu³⁺,Bi³⁺ was prepared by a high temperature solid-state reaction technique. The phosphor was characterized by X-ray diffraction (XRD), particle size analyzer and fluorescence spectrometer. The single phase of GdNbO₄:Eu³⁺,Bi³⁺ was obtained at 1150°C and the average particle diameter was about 2.30 ??m. Excitation and emission spectra reveal that the phosphor can be efficiently excited by ultraviolet (UV) light (394 nm) and emit the strong red light of 612 nm due to the Eu³⁺ transition of ⁵D₀??⁷F₂. The optimum content of Eu³⁺ doped in the phosphor GdNbO₄:Eu³⁺ is 20mol%. The phosphor Gd_0.80NbO₄:0.20Eu³⁺,0.03Bi³⁺ shows much stronger photoluminescence intensity and better chromaticity coordinates (x=0.642, 0.352) than GdNbO₄:Eu³⁺. It is confirmed that Gd_0.80NbO₄:0.20Eu³⁺,0.03Bi³⁺ is a potential candidate for near-UV chip-based white light emitting diodes.     

Preparation of Gd_2O_3 :Eu~(3+) downconversion luminescent material and its application in dye-sensitized solar cells

Gd₂O₃ :Eu³⁺ downconversion luminescent powder was prepared using the homogeneous precipitation method. Its optical properties were analyzed and it was introduced into a dye-sensitized solar cell （DSSC）. As a luminescence medium, Gd₂O₃ :Eu³⁺ improved light harvesting via conversion luminescence and increased the photocurrent of the DSSC. As a p-type dopant insulating rare earth oxides form an energy barrier, and the Gd₂O₃ :Eu³⁺ elevated the energy level of the oxide film and increased the photovoltage. The photoelectric conversion efficiency for a DSSC with Gd₂O₃ :Eu³⁺ doping （6 : 100） reached 7.01%, which was 17.4% higher than the photoelectrical conversion efficiency of a DSSC without Gd 2 O 3 :Eu 3+ doping.     

Thermal degradation of BaAl2Si2O8：Eu2＋ phosphor excited by near ultraviolet light

Eu2+ doped BaAl2Si2O8 phosphor was synthesized by one-step calcination of precursors that were prepared by chemical co-precipitation.The thermal degradation properties of BaAl2Si2O8:Eu2+ were investigated by photoluminescence,lifetime and chromaticity coordinate measurements.BaAl2Si2O8:Eu2+ is efficiently excited by incident light of 250-400 nm,which matches the emission of near ultraviolet LED chips well.BaAl2Si2O8:Eu2+ exhibits broad blue emission at 470 nm because of the 4f65d1-4f7(8S7/2) transition of Eu2+ ions,and the emission band shows an unusual blue shift with bandwidth broadening and emission intensity decreasing as the annealing temperature is increased.The luminescence decay and CIE chromaticity coordinates of BaAl2Si2O8:Eu2+ were determined to investigate its application in white LEDs.     

Energy transfer process between Eu3+ and wide-band-gap SnO2 nanocrystals in silica films studied by photoluminescence excitation and time-resolved photoluminescence techniques

Eu3+ions embedded in silica thin films codoped with SnO2 nanocrystals were fabricated by sol–gel and spin-coating methods.SnO2 nanocrystals with controllable sizes were synthesized through precisely controlling the Sn concentrations.The influences of doping and annealing conditions on the photoluminescence intensity from SnO2 nanocrystals are systematically investigated.The effective energy transfer from the defect states of SnO2nanocrystals to nearby Eu3+ions has revealed by the selective photoluminescence excitation spectra.The efficiency of the Forster resonance energy transfer is evaluated by the time-resolved photoluminescence measurements,which is about 29.1%based on the lifetime tests of the SnO2emission.     

Multi-color long-lasting phosphorescence of rare earth ions in CdSiO<Subscript>3</Subscript> matrix

A series of rare earth ions doped CdSiO3:RE^3 (RE=Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho,Er, Tin, Yb, Lu) multi-color long-lasting phosphorescence phosphors are prepared by the conventional hightemperature solid-state method. The results of XRD measurement indicate that the products fired under 1050~C for 3h have a good crystallization without any detectable amount of impurity phase. Rare earth ions doped CdSiO3 phosphors possess excellent Inmiuescence properties. When rare earth ions such as Y^3 , La^3 , Gd^3 , Lu^3 , Ce^3 , Nd^3 , Ho^3 , Er^3 ,Tm^3 and Yb^3 are introduced into the CdSiO3 host, one broadband centered at about 420 nm resulting from traps can be observed. In the case of other earth ions such as Pr^3 ,Sm^3 , Eu^3 , Tb^3 and Dy^3 , their characteristic line emitting as well as the -420 nm broadband luminescence can be obtained. The mixture of their characteristic line emitting with the -420 nm broadband Inminescence results in various afterglow color.     

Investigation of the electronic structure and photoluminescence properties of Eu3＋ in Sr2Mgl_xZnxSi207 （0 〈x 〈 1）

Undoped and Eu 3+-doped Sr 2 Mg 1-x Zn x Si 2 O 7 (0≤x≤1) powder crystals were obtained by conventional solid-state reaction.X-ray diffraction,inductively coupled plasma analysis,and Fourier transform infrared spectroscopy results implied that a complete solid-solution formed between Sr 2 MgSi 2 O 7 and Sr 2 ZnSi 2 O 7 as well as local structural adjustment.Excitation spectra exhibited O 2-Eu 3+ charge transfer (CT) bands centered at 250 nm for Sr 2 MgSi 2 O 7:Eu 3+ and 258 nm for Sr 2 ZnSi 2 O 7:Eu 3+.Emission spectra exhibited a major band around 616 nm,which showed the environment around Eu 3+ was non-centrosymmetric in both Sr 2 MgSi 2 O 7:Eu 3+ and Sr 2 ZnSi 2 O 7:Eu 3+.In addition,first principles calculations within the local density approximation (LDA) of density functional theory (DFT) were used to calculate the electronic structure of Sr 2 MgSi 2 O 7 and Sr 2 ZnSi 2 O 7.Calculated results were correlated with experimental UV-vis reflection spectra and the observed shift of the O 2-Eu 3+ CT band.     

Effects of La3+ and Gd3+ on Ca2+ influx in rat hepatoma H-35 cells

Effects of La³⁺ and Gd³⁺ on Ca²⁺ influx were investigated in rat hepatoma H-35 cells by measuring the initial rate of⁴⁵Ca²⁺ uptake. It was found that the maximum initial rate of Ca²⁺ uptake was increased six-to ten-fold at low concentrations of La³⁺ and Gd³⁺. Kinetic analyses by measuring the initial rate of Ca²⁺ influx at different external Ca²⁺ concentrations indicated the existence of two intracellular exchangeable components in the basal Ca²⁺ system, with low and high affinities for Ca²⁺, and only one class of Ca²⁺ binding sites was observed in the La³⁺-or Gd³⁺-treated cells. For high affinity, La³⁺ and Gd³⁺ increased both kinetic parametersK _m andV _max of basai Ca²⁺ influx. La³⁺ and Gd³⁺ compete directly with Ca²⁺ for Ca²⁺ binding site for low affinity. The kinetics is competitive.     

Photoluminescence and cathodoluminescence properties of CaLaGa<Subscript>3</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> phosphors

The CaLaGa₃O₇:Eu³⁺ phosphor was prepared by a chemical co-precipitation method. Field emission scanning electron microscopy (FE-SEM), laser particle size analysis, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence (CL) spectra were utilized to characterize the synthesized phosphor. The results revealed that the phosphor was composed of microspheres with a slight agglomerate phenomenon and was spherically shaped. The average grain size was about 1.0 μm. Eu³⁺ ions, as luminescent centers, substituted La³⁺ ions into the single crystal lattice of CaLaGa₃O₇ with the sites of C_s. Although the CL spectrum was greatly different from the PL spectrum, it had the strongest red emission corresponding to the ⁵D₀ →⁷F₂ transition of Eu³⁺. Under the excitation of UV light (287 nm) and electron beams (1.0–7.0 kV), the chromaticity coordinates of the phosphor were found to be in the nearly red and orange light regions, respectively.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

下转换发光粉Y2O3/Sm3+在染料敏化太阳能电池中的应用

采用沉淀法制备了Y2O3/Sm3+下转换发光粉,利用X射线衍射、荧光光谱对其进行了表征,并利用该发光粉具有下转换发光的特点将其应用于染料敏化太阳能电池(DSSC).结果表明,Y2O3/Sm3+下转换发光粉可以增加电池对太阳光的吸收范围,提高电池的光电流和光电压.研究了掺杂量对电池性能的影响,当掺杂量为3%时,光电转换效率从5.049%提高到5.94%,表明了其是一种有效提高光电转换效率的方法.     

Flexible dye-sensitized solar cell based on PCBM/P3HT heterojunction

Using blend heterojunction consisting of C60 derivatives [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) and poly(3-hexylthiophene) (P3HT) as charge carrier transferring medium to replace I3–/I– redox electrolyte,a novel flexible dye-sensitized solar cell (DSSC) is fabricated.The characterization of infrared spectra and ultraviolet-visible spectra shows that the PCBM/P3HT heterojunction has not only the absorption in ultraviolet light for PCBM,but also the absorption in visible and near infrared light for P3HT,which widens the photoelectric response range for DSSC.The influence of PCBM/P3HT mass ratio on the performance of the solar cell is discussed.Under 100 mW cm–2 (AM 1.5) simulated solar irradiation,the flexible solar cell achieves a lightto-electric energy conversion efficiency of 1.43%,open circuit voltage of 0.87 V,short circuit current density of 3.0 mA cm–2 and fill factor of 0.54.     

Si衬底掺杂浓度对InGaN/Si异质单结太阳电池性能的影响

【目的】研究p-Si衬底掺杂浓度对InGaN/Si异质单结太阳电池性能的影响,为制备高效太阳电池提供理论基础。【方法】将器件的n-InGaN掺杂浓度固定为10~(16 )cm~(-3),在改变p-Si衬底掺杂浓度N_A的情况下,采用一维光电子和微电子器件结构分析模拟软件(AMPS-1D)对InGaN/Si异质单结太阳电池器件的各项性能参数进行模拟。【结果】随着掺杂浓度N_A的升高,电池的电流密度J_(SC)和填充因子FF随之升高,当到达一定高的掺杂浓度范围时(N_A5.00×10~(17)cm~(-3)),J_(SC)基本保持不变,约为28.12mA/cm~2,FF保持在0.85左右且变化不大。开路电压V_(OC)和光电转换效率E_(ff)与掺杂浓度的大小呈正相关关系,随着N_A的增大,V_(OC)、E_(ff)缓慢增大。【结论】高掺杂浓度下的太阳电池具有较好的光电转换效率。低掺杂浓度的太阳电池光电转换效率较低,这是因为其对应的尖峰势垒高度和宽度均较大,影响了光生载流子的输运。     

掺杂稀土离子的BiY2Fe5O12结构与磁性

采用溶胶 凝胶法制备了Gd_xBiY_2-xFe₅O₁₂(x=0，0.1，0.2，0.4，0.6，0.8)纳米晶粉体系列样品. 利用DTA，TGA，XRD，TEM，IR和VSM等方法对材料的制备过程和产物进行分析. 结果表明， Gd的掺入并未改BiY₂Fe₅O₁₂的石榴石结构. 讨论了Gd离子掺入BiYIG铁氧体的粒 径、 形貌及磁性规律.     

基于掺铕钨酸盐荧光强度比的非接触温度传感

为了突破传统测温技术应用的局限性,利用NaY （WO₄）₂：Eu³⁺玻璃陶瓷（glass ceramics,GC）实现了具有非接触、实时响应、自校准等优势的双模荧光强度比（luminescence intensity ratio,LIR）测温。采用高温熔融淬灭法制备出含NaY （WO₄）₂：Eu³⁺纳米晶的透明GC样品,并进行系列光谱测量和热敏性能分析。结果表明,样品中Eu³⁺的激发态能级⁵D₁和⁵D₀和基态能级⁷F₂和⁷F₀为两对独立的热耦合能级,可分别基于这两对热耦合能级实现性能优异的双模LIR温度传感。该双模LIR测温技术数据可靠、测温范围广、灵敏度高,再结合GC材料优势,是可用于光纤温度传感器的核心技术材料。     

Bi~(3+)/Yb~(3+)共掺GdVO_4近红外发光性能研究

使用高温固相法制备了一种新的Bi3+,Yb3+共掺杂GdVO4量子裁剪近红外发光材料,该材料在波长为250~400nm的紫外光激发下发射出很强的近红外光(900~1100nm).由于体系中Bi3+离子的引入,相对于Gd0.9Yb0.1VO4,Gd0.87Yb0.1Bi0.03VO4在989nm处的近红外发光强度提高近120%,且其激发峰也从323nm红移至341nm,整个激发谱带更宽,更有利于实际应用.由于Yb3+离子既可以利用基质中的VO3-4电荷迁移态跃迁的能量,也可以同时利用Bi3+的1S0-3P1能级跃迁传递能量,相对于目前报道的理论量子裁剪效率最高的YVO4:Bi3+,Yb3+,GdVO4:Bi3+,Yb3+无论其近红外发光强度还是可见光发光强度强度皆有提升,是一种很有希望的紫外宽带激发近红外发光材料.