Bioactivity analysis of the Ta(Ⅴ) doped SiO_2–Ca O–Na_2O–P_2O_5 ceramics prepared by solid state sintering method

The main objective of the study was to control the degradation rate of material at a higher degradation rate improving the chemical stability of the material. Ta is known to have good chemical resistance, biocompatibility and show no adverse biological response. In the present study, Si O_2–Na_2O–Ca O–P_2O_5 bioceramics with different Ta_2O_5 contents was prepared by solid state sintering method at 1000 °C. The as-sintered ceramics were subjected to immersion studies in stimulated body fluid(SBF) for 21 days under static condition and characterized by XRD, FTIR, SEM, and AAS. The findings of the research indicate that the addition of Ta_2O_5 controlled degradability, and all samples showed sufficient bioactivity.     

Preparation of nano-TiO_2/diatomite-based porous ceramics and their photocatalytic kinetics for formaldehyde degradation

Diatomite-based porous ceramics were adopted as carriers to immobilize nano-TiO_2 via a hydrolysis-deposition technique. The thermal degradation of as-prepared composites was investigated using thermogravimetric–differential thermal analysis, and the phase and microstructure were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and transmission electron microscopy. The results indicated that the carriers were encapsulated by nano-TiO_2 with a thickness of 300–450 nm. The main crystalline phase of TiO_2 calcined at 650℃ was anatase, and the average grain size was 8.3 nm. The FT-IR absorption bands at 955.38 cm~(-1) suggested that new chemical bonds among Ti, O, and Si had formed in the composites. The photocatalytic(PC) activity of the composites was investigated under UV irradiation. Furthermore, the photodegradation kinetics of formaldehyde was investigated using the composites as the cores of an air cleaner. A kinetics study showed that the reaction rate constants of the gas-phase PC reaction of formaldehyde were κ = 0.576 mg·m~(–3)·min~(–1) and K = 0.048 m~3/mg.     

人工闪锌矿氧压酸浸过程中Cu2+的催化机理研究

The potential autoclave was used to study the catalytic mechanism of Cu2+ during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu2+ formed a CuS deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu2+. At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

Investigation of the kinetic mechanism of the demanganization reaction between carbon-saturated liquid iron and CaF_2–CaO–SiO_2-based slags

The demanganization reaction kinetics of carbon-saturated liquid iron with an eight-component slag consisting of CaO–SiO_2–MgO–FeO–MnO–Al_2O_3–TiO_2–CaF_2 was investigated at 1553, 1623, and 1673 K in this study. The rate-controlling step(RCS) for the demanganization reaction with regard to the hot metal pretreatment conditions was studied via kinetics analysis based on the fundamental equation of heterogeneous reaction kinetics. From the temperature dependence of the mass transfer coefficient of a transition-metal oxide(Mn O), the apparent activation energy of the demanganization reaction was estimated to be 189.46 k J·mol~(–1) in the current study, which indicated that the mass transfer of Mn O in the molten slag controlled the overall rate of the demanganization reaction. The calculated apparent activation energy was slightly lower than the values reported in the literature for mass transfer in a slag phase. This difference was attributed to an increase in the "specific reaction interface"(SRI) value, either as a result of turbulence at the reaction interface or a decrease of the absolute amount of slag phase during sampling, and to the addition of calcium fluoride to the slag.     

Reduction mechanism of high-chromium vanadium–titanium magnetite pellets by H_2–CO–CO_2 gas mixtures

The reduction of high-chromium vanadium–titanium magnetite as a typical titanomagnetite containing 0.95wt% V2O5 and 0.61wt% Cr2O3 by H2–CO–CO2 gas mixtures was investigated from 1223 to 1373 K. Both the reduction degree and reduction rate increase with increasing temperature and increasing hydrogen content. At a temperature of 1373 K, an H2/CO ratio of 5/2 by volume, and a reduction time of 40 min, the degree of reduction reaches 95%. The phase transformation during reduction is hypothesized to proceed as follows: Fe2O3 → Fe3O4 → FeO → Fe; Fe9 TiO 15 + Fe2Ti3O9 → Fe2.75Ti0.25O4 → FeT iO 3 → TiO 2;(Cr0.15V0.85)2O3 → Fe2VO4; and Cr1.3Fe0.7O3 → FeC r2O4. The reduction is controlled by the mixed internal diffusion and interfacial reaction at the initial stage; however, the interfacial reaction is dominant. As the reduction proceeds, the internal diffusion becomes the controlling step.     

Preparation and performance of LiNi_(0.8)Co_(0.2)O_2 cathode material based on Co-substituted α–Ni(OH)_2 precursor

Co-substituted α-Ni(OH)2 was synthesized by a novel microwave homogeneous precipitation method in the presence of urea. LiNi0.8Co0.2O2 cathode material was synthesized by calcining Co-substituted α-Ni(OH)2 precursor and LiOH·H2O at 900℃ for 10 h in flowing oxygen. XRD, FTIR, FESEM and electro- chemical tests were used to study the physical and the electrochemical performances of the materials. The results show that the prepared LiNi0.8Co0.2O2 compound has a good layered hexagonal structure. Moreover, the LiNi0.8Co0.2O2 cathode material demonstrates stable cyclability with a high initial specific discharge capacity of 183.9 mAh/g. The good electrochemical performance could be attributed to the uniform distribution of Ni2 and Co2 ions in the crystal structure and a minimal cation mixing in LiNi0.8Co0.2O2 host structure.     

Kinetic studies on the reduction of iron ore nuggets by devolatilization of lean-grade coal

An isothermal kinetic study of a novel technique for reducing agglomerated iron ore by volatiles released by pyrolysis of lean-grade non-coking coal was carried out at temperature from 1050 to 1200°C for 10–120 min. The reduced samples were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and chemical analysis. A good degree of metallization and reduction was achieved. Gas diffusion through the solid was identified as the reaction-rate-controlling resistance; however, during the initial period, particularly at lower temperatures, resistance to interfacial chemical reaction was also significant, though not dominant. The apparent rate constant was observed to increase marginally with decreasing size of the particles constituting the nuggets. The apparent activation energy of reduction was estimated to be in the range from 49.640 to 51.220 kJ/mol and was not observed to be affected by the particle size. The sulfur and carbon contents in the reduced samples were also determined.     

Effect of Yb2O3 doping on the grain boundary of NiFe2O4–10NiO-based cermets after sintering

xYb2O3–15(20Ni–Cu)/(85?x)(NiFe2O4–10NiO) (x=0, 0.25, 0.5, 0.75, 1.0, 2.0, and 10.0) cermets for aluminum electrolysis were prepared to investigate the effect of Yb2O3 doping on the grain boundary of the cermets after sintering. The results showed that each interface was very clear and that with increasing Yb2O3 content, most of the Yb was evenly distributed at the grain boundary. Moreover, according to the phase composition and microstructural analysis by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), and electron probe microanalysis (EPMA), YbFeO3 was produced along the grain boundary. The YbFeO3 was concluded to not only have formed from the interaction between the NiFe2O4 or Fe2O3 component and Yb2O3 at the grain boundary of the cermets, but also from the decomposition of NiFe2O4 into NiO and Fe2O3 and the subsequent reaction of Fe2O3 with Yb2O3. Thus, the pro-duction of YbFeO3 resulted in a cermet with high relative density, good electrical conductivity, and good corrosion resistance.     

Cu~(2+)-catalyzed mechanism in oxygen-pressure acid leaching of artificial sphalerite

The potential autoclave was used to study the catalytic mechanism of Cu~(2+) during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu~(2+) formed a Cu S deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu~(2+). At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

摩擦表面合金化法开发一种 Mg–Zn 表面合金:模拟体液中的体外降解研究

A new variant of friction-assisted process named friction surface alloying (FSA) for developing surface alloys was demonstrated in the present work. In FSA, the dispersed phase is melted and allowed to react with the matrix material to form an alloy at the surface of a metallic substrate. In the present work, magnesium (Mg) sheets and zinc (Zn) powder were selected, and fine grained (~3.5 μm) Mg–Zn surface alloy with improved hardness was produced by FSA. X-ray diffraction studies confirmed the formation of intermetallic phases of Mg and Zn at the surface. From the in vitro degradation studies carried out by immersing in simulated body fluids, a lower corrosion rate was observed for the Mg–Zn surface alloy compared with pure Mg. The surface morphologies after immersion studies indicated large degraded areas on the base Mg compared with Mg–Zn. The results demonstrate the potential of FSA in developing Mg-based surface alloys without melting the substrate to impart better surface properties.     

Developing Mg–Zn surface alloy by friction surface allosying: In vitro degradation studies in simulated body fluids

A new variant of friction-assisted process named friction surface alloying(FSA) for developing surface alloys was demonstrated in the present work. In FSA, the dispersed phase is melted and allowed to react with the matrix material to form an alloy at the surface of a metallic substrate. In the present work, magnesium(Mg) sheets and zinc(Zn) powder were selected, and fine grained(～3.5 μm) Mg–Zn surface alloy with improved hardness was produced by FSA. X-ray diffraction studies confirmed the formation of intermetallic phases of Mg and Zn at the surface. From the in vitro degradation studies carried out by immersing in simulated body fluids, a lower corrosion rate was observed for the Mg–Zn surface alloy compared with pure Mg. The surface morphologies after immersion studies indicated large degraded areas on the base Mg compared with Mg–Zn. The results demonstrate the potential of FSA in developing Mg-based surface alloys without melting the substrate to impart better surface properties.     

铝合金上热沉积氧化铝–二氧化钛涂层的固体颗粒冲蚀研究

Thermal barrier coatings are widely used as surface modifications to enhance the surface properties of the material and protect from surface degradations such as erosion and corrosion. Ceramic-based coatings are highly recommended to increase wear resistance in the industrial sector. In this paper, an alumina–titania ceramic powder was deposited on an aluminum alloy using an atmospheric plasma spray technique. Experimental investigations were performed to study the behavior and erosion rate of the material. Solid particle erosion studies were performed by varying the particle velocity and particle flow rate. The angle impingement and stand-off distance were constant for comparison. The base metal has a clinging effect and the mass change was negative at a maximum particle flow rate of 4 g·min?1. Under the same process conditions, the coated sample had a reduced lifetime and reached a maximum erosion rate of 0.052 (Δg/g). The solid particle erosion studies confirmed that the base metal aluminum alloy had severe surface damage with erodent reinforcement when compared to the coated samples. The influence of the particle velocity, particle flow rate, and input process parameters were also identified.     

Solid particle erosion studies of thermally deposited alumina–titania coatings on an aluminum alloy

Thermal barrier coatings are widely used as surface modifications to enhance the surface properties of the material and protect from surface degradations such as erosion and corrosion. Ceramic-based coatings are highly recommended to increase wear resistance in the industrial sector. In this paper, an alumina–titania ceramic powder was deposited on an aluminum alloy using an atmospheric plasma spray technique. Experimental investigations were performed to study the behavior and erosion rate of the material. Solid particle erosion studies were performed by varying the particle velocity and particle flow rate. The angle impingement and stand-off distance were constant for comparison.The base metal has a clinging effect and the mass change was negative at a maximum particle flow rate of 4 g·min~(-1). Under the same process conditions, the coated sample had a reduced lifetime and reached a maximum erosion rate of 0.052(Δg/g). The solid particle erosion studies confirmed that the base metal aluminum alloy had severe surface damage with erodent reinforcement when compared to the coated samples.The influence of the particle velocity, particle flow rate, and input process parameters were also identified.     

Synthesis of a NiTi_2–AlNi–Al_2O_3 nanocomposite by mechanical alloying and heat treatment of Al–TiO_2–NiO

The aim of the present study was to investigate the phases formed during ball milling of Al–TiO_2–NiO. For this purpose, a mixture of Al–TiO_2–NiO with a molar ratio of 6:1:1 was used. Characterization of the milled powders by X-ray diffraction, differential thermal analysis, field-emission scanning electron microscopy, and transmission electron microscopy showed the formation of nanocrystalline NiTi_2 along with AlNi. A thermodynamical investigation confirmed that NiO was reduced by Al during ball milling, which consequently promoted TiO_2 reduction and the formation of NiTi_2. Al is capable of reducing NiO either during ball milling or at temperatures above the melting point of Al; by contrast, TiO_2 can be reduced by Al only by milling.     

Electrical and band-gap properties of amorphous zinc–ind ium–tin oxide thin films

Zinc–indium–tin oxide (ZITO) films were grown by pulsed-laser deposition. Three different material compositions were investigated: ZITO-30, ZITO-50 and ZITO-70 in which 30%,50% and 70%, respectively, of the indium in the In2O3 structure was replaced by substitution with zinc and tin in equal molar proportions (co-substitution): In22xZnxSnxO3, where x=0.3, 0.5, 0.7. All ZITO films grown at room temperature were amorphous. The first evidence of crystallinity was observed at higher deposition-temperature as the degree of co-substitution was increased. A decrease in mobility and conductivity was also observed as the degree of co-substitution was increased. The highest mobility for ZITO-30 and ZITO-50 was observed at deposition temperatures just prior to crystallization. The effect of deposition temperature on carrier concentration was minor compared to the effect of oxygen partial pressure during deposition.     

Preparation and performance of LiNi0. 8Co0.2O2 cathode material based on Co-substituted α-Ni（OH）2 precursor

Co-substituted α-Ni（OH）2 was synthesized by a novel microwave homogeneous precipitation method in the presence of urea. LiNi0.8Co0.2O2 cathode material was synthesized by calcining Co-substituted α-Ni（OH）2 precursor and LiOH·H2O at 900℃for 10 h in flowing oxygen. XRD, FTIR, FESEM and electrochemical tests were used to study the physical and the electrochemical performances of the materials. The results show that the prepared LiNi0.8Co0.2O2 compound has a good layered hexagonal structure. Moreover, the LiNi0.8Co0.2O2cathode material demonstrates stable cyclability with a high initial specific discharge capacity of 183.9 mAh/g. The good electrochemical performance could be attributed to the uniform distribution of Ni^2＋ and Co^2＋ ions in the crystal structure and a minimal cation mixing in LiNi0.8Co0.2O2 host structure.     

Preparation of nano-TiO2/diatomite-based porous ceramics and their photocatalytic kinetics for formaldehyde degradation

Diatomite-based porous ceramics were adopted as carriers to immobilize nano-TiO₂ via a hydrolysis-deposition technique. The thermal degradation of as-prepared composites was investigated using thermogravimetric-differential thermal analysis, and the phase and microstructure were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and transmission electron microscopy. The results indicated that the carriers were encapsulated by nano-TiO₂ with a thickness of 300-450 nm. The main crystalline phase of TiO₂ calcined at 650℃ was anatase, and the average grain size was 8.3 nm. The FT-IR absorption bands at 955.38 cm-1 suggested that new chemical bonds among Ti, O, and Si had formed in the composites. The photocatalytic (PC) activity of the composites was investigated under UV irradiation. Furthermore, the photodegradation kinetics of formaldehyde was investigated using the composites as the cores of an air cleaner. A kinetics study showed that the reaction rate constants of the gas-phase PC reaction of formaldehyde were κ=0.576 mg·m-3·min-1 and K=0.048 m3.     

Biodegradable zinc-iron alloys: Complex study of corrosion behavior,mechanical properties and hemocompatibility

Zn-Fe alloys have been extensively investigated in this study with a view to their application as biodegradable bone implants. Biogenic element zinc is a very appropriate metal because of the ideal degradation rate compared to those of Mg and Fe. Studied alloys were made by compressing metallic powders in a content ratio of 100% Zn,Zn-1% Fe, Zn-2% Fe, Zn-5% Fe and Zn-10% Fe and sintering at 350°C for 1 h. Prepared samples were examined by optical microscopy, SEM and XRD. Corrosion behavior, mechanical testing and hemocompatibility were observed subsequently. The electrochemical performance of such materials was studied in the simulated body fluids. The enhanced corrosion rate was observed for all samples after iron addition due to the micro-galvanic effect between the pure Zn and Zn_(11)Fe intermetallic phase. The corrosion rate of the Zn-5% Fe alloyed sample was more than 20-times higher(2.89 mmpy) compared to the pure Zn. However, alloying with more than 5 wt %of iron diminished the mechanical performance of the material. Therefore, the performed mechanical and hemocompatibility tests showed acceptable biocompatibility of zinc and Zn-1% Fe and Zn-2% Fe samples.     

Effect of B2O3 on the aqueous tape casting and microwave properties of Li2O–Nb2O5–TiO2 ceramics

The effect of B2O3 addition on the aqueous tape casting, sintering, microstructure and microwave dielectric properties of Li2O-Nb2O5-TiO2 ceramics has been investigated. The tape casting slurries exhibit a typical shear-thinning behavior without thixotropy, but the addition of B2O3 increases the viscosity of the slurries significantly. It was found that doping of B2O3 can decrease the tensile strength, strain to failure and density of the green tapes. The sintering temperature could be lowed down to 900℃ with the addition of 2 wt% B2O3 due to the liquid phase effect. No secondary phase is observed. The addition of B2O3 does not induce much degradation on the microwave dielectric properties. Optimum microwave dielectric properties of εr 67, Q×f 6560 GHz are obtained for Li2O-Nb2O5-TiO2 ceramics containing 2 wt% B2O3 sintered at 900 1C. It represents that the ceramics could be promising for multilayer low-temperature co-fired ceramics (LTCC) application.     

Fe–0.3C–9Mn–2Al中锰钢的热塑性行为

The hot ductility of a Fe–0.3C–9Mn–2Al medium Mn steel was investigated using a Gleeble3800 thermo-mechanical simulator. Hot tensile tests were conducted at different temperatures (600–1300°C) under a constant strain rate of 4 × 10?3 s?1. The fracture behavior and mechanism of hot ductility evolution were discussed. Results showed that the hot ductility decreased as the temperature was decreased from 1000°C. The reduction of area (RA) decreased rapidly in the specimens tested below 700°C, whereas that in the specimen tested at 650°C was lower than 65%. Mixed brittle–ductile fracture feature is reflected by the coexistence of cleavage step, intergranular facet, and dimple at the surface. The fracture belonged to ductile failure in the specimens tested between 720–1000°C. Large and deep dimples could delay crack propagation. The change in average width of the dimples was in positive proportion with the change in RA. The wide austenite–ferrite intercritical temperature range was crucial for the hot ductility of medium Mn steel. The formation of ferrite film on austenite grain boundaries led to strain concentration. Yield point elongation occurred at the austenite–ferrite intercritical temperature range during the hot tensile test.