高炉灰为还原剂对海滨钛磁铁矿直接还原焙烧磁选--钛铁分离的影响

对高炉灰在直接还原焙烧-弱磁选工艺中用作印尼某海滨钛磁铁矿还原剂的可行性及其机理进行研究.结果表明,以萤石为添加剂的条件下,高炉灰可代替煤做还原剂,通过高炉灰与萤石的共同作用,可以在直接还原过程中提高还原铁粉中铁的回收率及品位并降低TiO2质量分数,同时回收高炉灰中铁.三种不同产地高炉灰还原效果的比较表明,高炉灰性质对还原效果有影响.在相同用量条件下,津鑫高炉灰( JX)还原效果最好;在JX高炉灰用量30%、萤石用量10%、焙烧温度1250益以及焙烧时间为60 min时,焙烧产物通过两段磨矿和两段磁选,最终得到最佳的还原铁粉中铁品位为91.28%,TiO2质量分数降至0.93%,包括海滨砂矿和高炉灰中铁的铁总回收率达到89.19%.     

锌浸出渣的还原焙烧和人工硫化矿物浮选过程中硫酸铅和硫酸锌的反应行为

To evaluate the feasibility of recovering Pb and Zn sulfides and Ag-containing minerals from Zn leaching residue by the process of reduction roasting followed by flotation, the reaction behaviors of Pb and Zn sulfates during this process were investigated. Chemical analysis showed that the transformation ratios of PbSO₄ and ZnSO₄ could reach 65.51% and 52.12%, respectively, after reduction roasting, and the introduction of a sulfidation agent could improve the transformation ratios of these sulfates. scanning electron microscopy–energy dispersive spectroscopy (SEM–EDS) revealed that temperature obviously affects the particle size, crystal growth, and morphology of the artificial Pb and Zn sulfide minerals. Particle size analysis demonstrated that the particle size of the materials increases after roasting. Flotation tests revealed that a flotation concentrate composed of 12.01wt% Pb, 27.78wt% Zn, and 6.975 × 10?2wt% Ag with recoveries of 60.54%, 29.24%, and 57.64%, respectively, could be obtained after roasting.     

铁酸锌气体还原的热力学分析

根据热力学原理,计算并分析了含锌冶金粉尘中的重要成分ZnFe2 O4在CO- CO2气体还原过程中的热力学行为. ZnFe2 O4的气体还原遵循逐级还原规律,且ZnFe2 O4很容易被CO还原到ZnO和Fe3 O4.较高温度条件下,ZnO的气体还原易于FeO的还原.随着反应温度升高,锌完全反应和挥发所需要的CO含量不断降低,当反应温度从1100 K升高到1400 K时所需的CO体积分数由0.4降低到0.01以下.要达到还原分离金属锌的目的,不必将铁氧化物还原到金属铁,而只需将铁氧化物还原到Fe3 O4或FeO,同时满足锌的还原条件即可.在高炉炉身中上部,由于发生锌的还原反应和内部循环,给高炉生产带来危害,因此应减少和控制高炉的锌负荷.     

基于低镁烧结矿和熔剂性球团的综合炉料熔滴性能研究

A low MgO content in sinter is conducive to reduce the MgO content in blast furnace slag. This study investigated the effect of MgO content in sinter on the softening–melting behavior of the mixed burden based on fluxed pellets. When the MgO content increased from 1.31wt% to 1.55wt%, the melting temperature of sinter increased to 1521°C. Such an increase was due to the formation of the high-melting-point slag phase. The reduction degradation index of sinter with 1.31wt% MgO content was better than that of others. The initial softening temperature of the mixed burden increased from 1104 to 1126°C as MgO content in sinter increased from 1.31wt% to 1.55wt%, and the melting temperature decreased from 1494 to 1460°C. The permeability index (S-value) of mixed burden decreased to 594.46 kPa·°C under a high MgO content with 1.55wt%, indicating that the permeability was improved. The slag phase composition of burden was mainly akermarite (Ca₂MgSiO₇) when the MgO content in sinter was 1.55wt%. The melting point of akermarite is 1450°C, which is lower than other phases.     

Evolution of ferronickel particles during the reduction of low-grade saprolitic laterite nickel ore by coal in the temperature range of 900–1250℃with the addition of CaO–CaF2–H3BO3

The method of producing ferronickel at low temperature(1250–1400℃)has been applied since the 1950s at Nippon Yakin Kogyo,Oheyama Works,Japan.Limestone was used as an additive to adjust the slag composition for lowering the slag melting point.The ferronickel product was recovered by means of a magnetic separator from semi-molten slag and metal after water quenching.To increase the efficiency of magnetic separation,a large particle size of ferronickel is desired.Therefore,in this study,the influences of CaO,CaF₂,and H₃BO₃ additives on the evolution of ferronickel particle at≤1250℃were investigated.The experiments were conducted at 900–1250℃with the addition of CaO,CaF₂,and H₃BO₃.The reduction processes were carried out in a horizontal tube furnace for 2 h under argon atmosphere.At 1250℃,with the CaO addition of 10 wt%of the ore weight,ferronickel particles with size of 20μm were obtained.The ferronickel particle size increased to 165μm by adding 10 wt%CaO and 10 wt%CaF₂.The addition of boric acid further increased the ferronickel particle size to 376μm,as shown by the experiments with the addition of 10 wt%CaO,10 wt%CaF₂,and 10 wt%H₃BO₃.     

Effects of SiO2 on the preparation and metallurgical properties of acid oxidized pellets

The effects of SiO₂ content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investigated.Mineralogical structures, elemental distribution, and pore size distribution were varied to analyze the mechanism of the effects.The results show that with an increase in SiO₂ content from 3.51 wt%to 7.18 wt%, compressive strength decreases from 3150 N/pellet to 2100 N/pellet and reducibility decreases from 76.5% to 71.4%.The microstructure showed that pellets with high SiO₂ content contained more magnetite in the mineralogical structures.Additionally, some liquid phases appeared, which hindered the continuous crystallization of hematite.Also, the softening–melting properties of the pellets clearly deteriorated as the SiO₂ content increased.With increasing SiO₂ content, the temperature range of the softening–melting zone decreased, and the maximum differential pressure and the comprehensive permeability index increased significantly.When acid oxidized pellets are used as the raw materials for blast furnace smelting, it should be combined with high basicity sinters to improve the softening–melting behaviors of the comprehensive charge.     

低品位软锰矿流态化还原焙烧

采用流化床和马弗炉,进行了流态化还原焙烧与静态堆积焙烧对比实验,前者还原焙烧时间和还原效率明显优于后者．以CO和N2分别作为还原气体和流体介质进行了流态化还原焙烧实验,考察焙烧温度、焙烧时间和还原气氛等对还原效率的影响．在焙烧温度800℃、焙烧时间3min以及CO体积分数10％时,软锰矿中二氧化锰的还原效率大于97％．在此基础上导出了还原动力学方程,并证实还原过程由界面化学反应控制,求得表观活化能为38．817kJ·mol^-1.     

基于优化氧化铁皮和焦粉配比的铁矿烧结过程NOx减排研究

Reducing NO_x emission of iron ore sintering process in a cost effective manner is a challenge for the iron and steel industry at present. Effects of the proportion of mill scale and coke breeze on the NO_x emission, strength of sinter, and sinter indexes were studied by combustion and sinter pot tests. Results showed that the peak value of NO concentration, total of NO emission, and fuel-N conversion rate gradually decreased as the proportions of the mill scale increased because NO was reduced to N₂ by Fe₃O₄, FeO, and Fe in the mill scale. The strength of sinter reached the highest value at 8.0wt% mill scale due to the formation of minerals with low melting point. The fuel-N conversion rate slightly fluctuated and total NO_x emission significantly decreased with the decreased proportions of coke breeze because CO formation and content of N element in the sintered mixture decreased. However, the sinter strength also decreased due to the decrease in the amount of the melting minerals. Furthermore, results of the sinter pot tests indicated that NO_x emission decreased. The sinter indexes performed well when the proportions of mill scale and coke breeze were 8.0wt% and 3.70wt% respectively in the sintered mixture.     

Two-stage reduction for the preparation of ferronickel alloy from nickel laterite ore with low Co and high MgO contents

The preparation of ferronickel alloy from the nickel laterite ore with low Co and high MgO contents was studied by using a pre-reduction-smelting method. The effects of reduction time, calcination temperature, quantity of reductant and calcium oxide (CaO), and pellet diameter on the reduction ratio of Fe and on the pellet strength were investigated. The results show that, for a roasting temperature >800℃, a roasting time >30 min, 1.5wt% added anthracite coal, 5wt% added CaO, and a pellet size of~10 mm, the reduction ratio of Fe exceeds 70% and the compressive strength of the pellets exceeds 10 kg per pellet. Reduction smelting experiments were performed by varying the smelting time, temperature, quantity of reductant and CaO, and reduction ratio of Fe in the pellets. Optimal conditions for the reduction smelting process are as follows:smelting time, 30-45 min; smelting temperature, 1550℃; quantity of reductant, 4wt%-5wt%; and quantity of CaO, 5wt%; leading to an Fe reduction ratio of 75% in the pellets. In addition, the mineral composition of the raw ore and that during the reduction process were investigated by process mineralogy.     

用离心法代替浮选提纯镜铁矿制备氧化铁红色素

This study used specularite, a high-gradient magnetic separation concentrate, as a raw material in reverse flotation. An iron concentrate with a grade of 65.1wt% and a recovery rate of 75.31% were obtained. A centrifugal concentrator served as the deep purification equipment for the preparation of iron oxide red pigments, and its optimal rotating drum speed, feed concentration, and other conditions were determined. Under optimal conditions, a high-purity iron oxide concentrate with a grade of 69.38wt% and a recovery rate of 80.89% were obtained and used as a raw material for preparing iron oxide red pigment. Calcining with sulfuric acid produced iron red pigments with different hues. Simultaneously, middlings with a grade of 60.20wt% and a recovery rate of 17.51% were obtained and could be used in blast furnace ironmaking. High-value utilization of specularite beneficiation products was thus achieved.     

炉顶煤气循环氧气高炉一维气固换热与反应动力学模型

结合风口回旋区燃烧和炉外煤气预热、脱除和循环的平衡关系,建立了氧气高炉一维气固换热与反应动力学模型,并采用传统高炉的运行和解剖数据对模型进行了验证分析.通过模型研究了氧气含量和上部循环煤气流量对氧气高炉炉内过程变量的影响规律.结果表明：氧气含量偏低和上部循环煤气流量不足时,会降低铁矿石还原效果,炉渣内出现大量未还原铁氧化物;氧气含量和上部循环煤气流量的提高可以有效提高炉内CO含量和铁矿石还原速度,但提高上部循环煤气流量会大幅提升炉顶煤气温度,增大热量损失.与传统高炉相比,氧气高炉内CO含量提高1.0~1.5倍,炉内气体还原性更强;铁矿石还原完成位置提高1.49 m,全炉还原反应速度更快;直接还原度降低55.2%~79.2%,炉内直接还原反应消耗的碳量更少.     

Micromorphology and safety properties of meager and meager-lean coal for blast furnace injection

Four types of meager and meager-lean coal and one type of high-quality anthracite were selected based on the safety requirements for blast furnace coal injection and domestic coal quality to conduct microstructure and component analyses.The analyses of the organic and inorganic macerals and the chemical compositions of the selected coal samples indicate that the four types of meager and meager-lean coal have low volatilization,low ash content,and low sulfur content;these qualities are suitable for blast furnace injection.Grindability test was conducted on the four types of meager and meager-lean coal and the anthracite mixed coal samples.Results indicate that the mixture of meager and meager-lean coal and anthracite is beneficial to improve the grindability of pulverized coal.The explosive tests reveal that the selected coal samples are non-explosive or weakly explosive.When the proportion of meager and meager-lean coal is less than 40wt%,the mixed coal powder would not explode during the blowing process.The minimum ignition temperature test determines that the minimum ignition temperatures of the four types of meager and meager-lean coal and anthracite are 326,313,310,315,and 393°C,respectively.This study provides a guiding research idea for the safety of meager and meager-lean coal used in blast furnace injection.     

高炉煤气除尘系统的设计

以1000m3高炉为例,本文详细介绍了高炉煤气除尘系统的设计。     

某高磷鲕状赤铁矿磷赋存状态及还原焙烧脱磷研究

采用浸出、电渗析等试验方法研究了尼日利亚高磷鲕状赤铁矿中磷的赋存状态并采用XRD和SEM分析添加脱磷剂Na2CO3直接还原焙烧产物的特性.结果表明,含磷矿物主要是呈微细粒包裹体嵌布在铁矿物鲕粒的裂隙或孔洞中的纤磷钙铝石(CaAl3(OH)6(HPO4)(PO4))、蓝磷铝铁矿(FeAl2(PO4)2OH·6H2O)以及均匀分散在铁矿物中的磷.通过添加脱磷剂Na2CO3的还原焙烧磁选可实现高效铁磷分离.磷通过两种方式去除:一部分含磷矿物与金属铁分离,存在于脉石矿物中,通过磨矿磁选可以有效去除,一部分含磷矿物与Na2CO3反应生成溶于水的磷矿物,最终使得还原铁产品中的磷含量降低.     

无烟煤还原硫化焙烧高硅低铁低品位锡中矿回收锡

A new method for separating and recovering tin from a low-grade tin middling with high Si content and low Fe content by roasting with anthracite coal was researched by studying the reaction mechanism and performing an industrial test, in which the Sn was sulfurized into SnS(g) and then collected using a dust collector. The Fe–Sn alloy may be formed at roasting temperatures above 950°C, and like the roasting temperature increases, the Sn content and Sn activity in this Fe–Sn alloy decrease. Also, more FeS can be formed at higher temperatures and then the formation of FeO–FeS with a low melting point is promoted, which results in more serious sintering of this low-grade tin middling. And from the thermodynamics and kinetics points of view, the volatilization of the Sn decreases at extremely high roasting temperatures. The results of the industrial test carried out in a coal-fired rotary kiln show that the Sn volatilization rate reaches 89.7% and the Sn is concentrated in the collected dust at a high level, indicating that the Sn can be effectively extracted and recovered from the low-grade tin middling with a high Si content and low Fe content through a reduction–sulfurization roasting process.     

钢铁厂含铁粉尘的合理利用

为了解决钢铁企业粉尘污染越来越严重的问题,合理地回收和利用含铁资源,作者运用添加精矿粉和其它粘结剂成型的方法,采用回转窑预还原的工艺手段,对武钢各种含铁粉尘的回收利用进行了广泛的实验研究,探讨了回收工艺的合理性、经济性及可行性,获得了适宜于作为高炉炉料或炼钢用添加料的优质球团。     

MgO对含钛烧结矿矿相结构及软熔滴落性能的影响

为了深入探究MgO对烧结矿矿物组成及冶金性能的影响,采用扫描电子显微镜和荷重软化熔滴设备研究了MgO对含钛烧结矿矿相结构与软熔滴落性能影响.实验结果表明,随着烧结料中MgO质量分数从2.04％增加到3.96％,烧结过程液相生成量逐渐减少,烧结矿中的赤铁矿和铁酸钙等含量都有不同程度的降低,赤铁矿质量分数从13.57％降低到9.99％,铁酸钙的质量分数由38.7％降低到30.17％,磁铁矿、硅酸盐和烧结矿中的孔洞逐步增加.因此,增加烧结矿中MgO会降低烧结矿中液相生成量,不利于烧结矿转鼓强度和还原性的提高.高碱度含钛烧结矿中的镁主要分布于烧结矿中复合铁酸钙相中,进一步提高烧结矿中镁的质量分数,烧结矿的磁铁矿相比例将增加,有一部分镁固溶于磁铁矿中;在高镁烧结矿中,也会形成一定量的橄榄石,其中固溶有少量镁、钛等元素.随着烧结矿中MgO质量分数的增加,开始软化温度逐渐升高,试样软化开始温度均在1120℃以上,软化温度区间△tA随着MgO含量的升高而逐渐变宽.     

含硼铁精矿用于巴润精矿氧化球团生产的实验研究

在实验室条件下,研究了含硼铁精矿对巴润精矿氧化球团制备工艺及冶金性能的影响.研究表明:球团原料中外配5.0%的含硼铁精矿,可将混合料中的巴润精矿配比(质量分数)提高到40%,制备的氧化球团满足高炉冶炼要求;含硼铁精矿可增加巴润精矿氧化球团的抗压强度和降低还原膨胀率,并可降低球团的焙烧温度;当含硼铁精矿配加量(质量分数)从0增加到7.5%时,球团抗压强度从2 630 N·个-1上升到3 709 N·个-1,还原膨胀率从25.69%降低到15.53%;外配质量分数为7.5%的含硼铁精矿时,球团的焙烧温度可从1 200℃降低至1 150℃,巴润精矿氧化球团满足高炉生产要求.     

利用自动解离分析方法研究硫化铜尾矿的矿物学特征:谦比希铜矿尾矿的实例研究

As ore grades constantly decline, more copper tailings, which still contain a considerable amount of unrecovered copper, are expected to be produced as a byproduct of froth flotation. This research reveals the occurrence mechanism of copper minerals in typical copper sulfide tailings using quantitative mineral liberation analysis (MLA) integrated with scanning electron microscopy–energy dispersive spectroscopy (SEM–EDS). A comprehensive mineralogical characterization was carried out, and the results showed that almost all copper minerals were highly disseminated within coarse gangue particles, except for 9.2wt% chalcopyrite that occurred in the 160–180 μm size fraction. The predominant copper-bearing mineral was chalcopyrite, which was closely intergrown with orthoclase and muscovite rather than quartz. The flotation tailings sample still contained 3.28wt% liberated chalcopyrite and 3.13wt% liberated bornite because of their extremely fine granularity. The SEM–EDS analysis further demonstrated that copper minerals mainly occurred as fine dispersed and fully enclosed structures in gangue minerals. The information obtained from this research could offer useful references for recovering residual copper from flotation tailings.     

深度还原-弱磁选回收稀土尾矿中铁的试验研究

对某全铁品位为1625%的稀土尾矿进行了深度还原-弱磁选回收铁试验研究,研究了还原剂种类及用量、焙烧温度及时间、磨矿细度及磁场强度对铁精矿品位和回收率的影响,并采用SEM,XRD等手段对稀土尾矿、焙烧产物、铁精矿进行了测试.结果表明,在烟煤质量分数30%,焙烧温度1300℃,焙烧时间60min,磨矿细度-0074mm占75%,磁场强度118kA/m的条件下,所得铁精矿TFe品位可达8076%,铁回收率可达9324%;稀土尾矿经深度还原后,其中的赤、褐铁矿、硅酸铁等含铁矿物转化为单质铁,铁精矿品位和回收率较常规选矿方法大幅度提高,同时脉石矿物组成简单,有利于萤石的富集回收.