Mineral-phase evolution and sintering behavior of MO–SiO_2–Al_2O_3–B_2O_3 (M = Ca,Ba) glass-ceramics by low-temperature liquid-phase sintering

In this work, network former SiO_2 and network intermediate Al_2O_3 were introduced into typical low-melting binary compositions CaO·B_2O_3, CaO·2B_2O_3, and BaO·B_2O_3 via an aqueous solid-state suspension milling route. Accordingly, multiple-phase aluminosilicate glass-ceramics were directly obtained via liquid-phase sintering at temperatures below 950°C. On the basis of liquid-phase sintering theory, mineral-phase evolutions and glass-phase formations were systematically investigated in a wide MO–SiO_2–Al_2O_3–B_2O_3(M = Ca, Ba) composition range. The results indicate that major mineral phases of the aluminosilicate glass-ceramics are Al_(20)B_4O_(36), CaAl_2Si_2O_8, and BaAl_2Si_2O_8 and that the glass-ceramic materials are characterized by dense microstructures and excellent dielectric properties.     

单斜相SrAl2Si2O8陶瓷的烧结及其对Sr的固化

Monoclinic SrAl₂Si₂O₈ ceramics for Sr immobilization were prepared by a liquid-phase sintering method. The sintering temperature, mineral phase composition, microstructure, flexural strength, bulk density, and Sr ion leaching characteristics of the SrAl₂Si₂O₈ ceramics were investigated. A crystalline monoclinic SrAl₂Si₂O₈ phase formed through liquid-phase sintering at 1223 K. The introduction of four flux agents (B₂O₃, CaO·2B₂O₃, SrO·2B₂O₃, and BaO·2B₂O₃) to the SrAl₂Si₂O₈ ceramics not only reduced the densification temperature and decreased the volatilization of Sr during high-temperature sintering but also impacted the mechanical properties of the ceramics. Product consistency tests showed that the leaching concentration of Sr ions in the sample with flux agent B₂O₃ was the lowest, whereas that of Sr ions in the sample with flux agent BaO·2B₂O₃ was the highest. These results show that the leaching concentration of Sr ions depends largely on the amorphous phase in the ceramics. Meanwhile, the formation of mineral analog ceramics containing Sr is an important factor to improve Sr immobilization.     

Sintering Behavior and Microstructure of diphasic β-Sialon/Al2O3 Composites

Six compositions with different ratio of β-Sialon/Al₂O₃ were synthesized from Al₂O₃, Si₃N₄ and SiO₂ by sintering with 3%Y₂O₃(mass fraction) as addition under the cover with powders of SiC+C and at nitrogen atmosphere. Theeffects of atmosphere, sintering temperature and composition on the sintering behavior were studied. The results showedthat the composites reached the best sintering behavior with the highest density about 92% at 1 650℃ under the weakreduction atmosphere. Finally the relative density of diphasic β-Sialon and β-Sialon/Al₂O₃ composites were studied andpredicted using ANN (Artificial Neural Networks) method and the results were experimental examined by fore randomsamples.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

In situ reaction mechanism of MgAlON in Al-Al2O3-MgO composites at 1700℃ under flowing N2

The Al-Al₂O₃-MgO composites with added aluminum contents of approximately 0wt%, 5wt%, and 10wt%, named as M₁, M₂, and M₃, respectively, were prepared at 1700℃ for 5 h under a flowing N₂ atmosphere using the reaction sintering method. After sintering, the Al-Al₂O₃-MgO composites were characterized and analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that specimen M₁ was composed of MgO and MgAl₂O₄. Compared with specimen M₁, specimens M₂ and M₃ possessed MgAlON, and its production increased with increasing aluminum addition. Under an N₂ atmosphere, MgO, Al₂O₃, and Al in the matrix of specimens M₂ and M₃ reacted to form MgAlON and AlN-polytypoids, which combined the particles and the matrix together and imparted the Al-Al₂O₃-MgO composites with a dense structure. The mechanism of MgAlON synthesis is described as follows. Under an N₂ atmosphere, the partial pressure of oxygen is quite low; thus, when the Al-Al₂O₃-MgO composites were soaked at 580℃ for an extended period, aluminum metal was transformed into AlN. With increasing temperature, Al₂O₃ diffused into AlN crystal lattices and formed AlN-polytypoids; however, MgO reacted with Al₂O₃ to form MgAl₂O₄. When the temperature was greater than (1640 ±10)℃, AlN diffused into Al₂O₃ and formed spinel-structured AlON. In situ MgAlON was acquired through a solid-solution reaction between AlON and MgAl₂O₄ at high temperatures because of their similar spinel structures.     

In-situ fabrication of Al(Zn)-Al2O3 graded composite using the aluminothermic reaction during hot pressing

In this study, the fabrication of multilayer Al(Zn)–Al₂O₃ with different volume fractions of Al₂O₃ was investigated. Al and ZnO powders were milled by a planetary ball mill, after which five-layer functionally graded samples were produced through hot pressing at 580℃ and 90 MPa pressure for 30 min. Formation of reinforcing Al₂O₃ particles occurred in the aluminum matrix via the aluminothermic reaction. Determination of the ignition temperature of the aluminothermic reaction was accomplished using differential thermal and thermogravimetric analyses. Scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffractometery analyses were utilized to characterize the specimens. The thermal analysis results showed that the ignition temperatures for the aluminothermic reaction of layers with the highest and lowest ZnO contents were 667 and 670℃, respectively. Microstructural observation and chemical analysis confirmed the fabrication of Al(Zn)–Al₂O₃ functionally graded materials composites with precipitation of additional Zn in the matrix. Moreover, nearly dense functionally graded samples demonstrated minimum and maximum hardness values of HV 75 and HV 130, respectively.     

Alkaline digestion behavior and alumina extraction from sodium aluminosilicate generated in pyrometallurgical process

In pyrometallurgical process, Al-and Si-bearing minerals in iron and aluminum ores are easily transformed into sodium aluminosilicates in the presence of Na₂O constituents, which alters the leaching behaviors of Al₂O₃ and SiO₂. It was confirmed that sodium aluminosilicates with different phase compositions synthesized at various roasting conditions were effectively digested in the alkaline digestion process. Under the optimum conditions at temperature of 100-120℃, liquid-to-solid ratio (L/S) of 10:2 mL/g, caustic ratio of 4, and Na₂O concentration of 240 g/L, the actual and relative digestion ratio of Al₂O₃ from the synthesized sodium aluminosilicates reached maximums of about 65% and 95%, respectively, while SiO₂ was barely leached out. To validate the superior digestion property of sodium aluminosilicate generated via an actual process, the Bayer digestion of an Al₂O₃-rich material derived from reductive roasting of bauxite and comprising Na_1.75Al_1.75Si_0.25O₄ was conducted; the relative digestion ratio of Al₂O₃ attained 90% at 200℃.     

18wt%Cr–8wt%Ni不锈钢中增塑性MnO–Al2O3–SiO2基非金属夹杂物的演变及其浸泡性能

The properties of MnO–Al₂O₃–SiO₂-based plasticized inclusion are likely to change during soaking  process due to its low melting point. In this study, the evolution of the MnO–Al₂O₃–SiO₂-based inclusion of 18wt%Cr?8wt%Ni stainless steel under isothermal soaking process at 1250°C for different times was investigated by laboratory-scale experiments and thermodynamic analysis. The results showed that the inclusion population density increased at the first stage and then decreased while their average size first decreased and then increased. In addition, almost no Cr₂O₃-concentrated regions existed within the inclusion before soaking, but more and more Cr₂O₃ precipitates were formed during soaking. Furthermore, the plasticity of the inclusion deteriorated due to a decrease in the amount of liquid phase and an increase in the high-melting-point-phase MnO–Cr₂O₃ spinel after the soaking process. In-situ observations by high-temperature confocal laser scanning microscopy (CLSM) confirmed that liquid phases were produced in the inclusions and the inclusions grew rather quickly during the soaking process. Both the experimental results and thermodynamic analysis conclude that there are three routes for inclusion evolution during the soaking process. In particular, Ostwald ripening plays an important role in the inclusion evolution, i.e., MnO–Al₂O₃–SiO₂-based inclusions grow by absorbing the newly precipitated smaller-size MnO–Cr₂O₃ inclusions.     

Acting mechanism of F,K, and Na in the solid phase sintering reaction of the Baiyunebo iron ore

The effect of F, K, and Na on the solid phase reaction of the Baiyunebo iron ore was investigated by differential thermal analysis (DTA) and X-ray diffraction (XRD). It has been identified that alkaline elements K and Na in the Baiyunebo ore instigate the formation of low melting point compounds Na₂SiO₃ and Na₂O·Fe₂O₃ and the generation of molten state in the solid phase sintering. Element F in the Baiyunebo ore facilitates the formation of cuspidine compound 3CaO·2SiO₂·CaF₂ in the solid phase reaction. The cuspidine compound is kept in solid as one of the final products through the entire sintering process due to its high melting point. In the sintering process, CaF₂ and SiO₂ react with CaO first and form 3CaO·2SiO₂·CaF₂ and 3CaO·2SiO₂, so the formation of ferrites, Na₂O·Fe₂O₃, and 2CaO·Fe₂O₃ is inhibited.     

Phosphate enrichment mechanism in CaO–SiO2–FeO–Fe2O3–P2O5 steelmaking slags with lower binary basicity

The addition of silica to steelmaking slags to decrease the binary basicity can promote phosphate enrichment in quenched slag samples. In this study, we experimentally investigated phosphate enrichment behavior in CaO–SiO₂–FeO–Fe₂O₃–P₂O₅ slags with a P₂O₅ content of 5.00% and the binary basicity B ranging from 1.0 to 2.0, where the (%Fe_tO)/(%CaO) mass percentage ratio was maintained at 0.955. The experimental results are explained by the defined enrichment degree R_C2S-C3P of solid solution 2CaO·SiO₂–3CaO·P₂O₅ (C₂S–C₃P), where R_C2S-C3P is a component of the developed ion and molecule coexistence theory (IMCT)–N_i model for calculating the mass action concentrations N_i of structural units in the slags on the basis of the IMCT. The asymmetrically inverse V-shaped relation between phosphate enrichment and binary basicity B was observed to be correlated in the slags under applied two-stage cooling conditions. The maximum content of P₂O₅ in the C₂S–C₃P solid solution reached approximately 30.0% when the binary basicity B was controlled at 1.3.     

Effect of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> on the crystallization behavior of glass-ceramics produced from naturally cooled yellow phosphorus furnace slag

CaO-Al₂O₃-SiO₂ (CAS) glass-ceramics were prepared via a melting method using naturally cooled yellow phosphorus furnace slag as the main raw material. The effects of the addition of Fe₂O₃ on the crystallization behavior and properties of the prepared glass-ceramics were studied by differential thermal analysis, X-ray diffraction, and scanning electron microscopy. The crystallization activation energy was calculated using the modified Johnson-Mehl-Avrami equation. The results show that the intrinsic nucleating agent in the yellow phosphorus furnace slag could effectively promote the crystallization of CAS. The crystallization activation energy first increased and then decreased with increasing amount of added Fe₂O₃. At 4wt% of added Fe₂O₃, the crystallization activation energy reached a maximum of 676.374 kJ·mol-1. The type of the main crystalline phase did not change with the amount of added Fe₂O₃. The primary and secondary crystalline phases were identified as wollastonite (CaSiO₃) and hedenbergite (CaFe(Si₂O₆)), respectively.     

Activity coefficients of NiO and CoO in CaO-Al2O3-SiO2 slag and their application to the recycling of Ni-Co-Fe-based end-of-life superalloys via remelting

To design optimal pyrometallurgical processes for nickel and cobalt recycling, and more particularly for the end-of-life process of Ni-Co-Fe-based end-of-life (EoL) superalloys, knowledge of their activity coefficients in slags is essential. In this study, the activity coefficients of NiO and CoO in CaO-Al₂O₃-SiO₂ slag, a candidate slag used for the EoL superalloy remelting process, were measured using gas/slag/metal equilibrium experiments. These activity coefficients were then used to consider the recycling efficiency of nickel and cobalt by remelting EoL superalloys using CaO-Al₂O₃-SiO₂ slag. The activity coefficients of NiO and CoO in CaO-Al₂O₃-SiO₂ slag both show a positive deviation from Raoult's law, with values that vary from 1 to 5 depending on the change in basicity. The activity coefficients of NiO and CoO peak in the slag with a composition near B=(%CaO)/(%SiO₂)=1, where B is the basicity. We observed that controlling the slag composition at approximately B=1 effectively reduces the cobalt and nickel oxidation losses and promotes the oxidation removal of iron during the remelting process of EoL superalloys.     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Dissolution of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript> inclusions in CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags at 1823 K

Al-Ti-O inclusions always clog submerged nozzles in Ti-bearing Al-killed steel. A typical synthesized Al₂TiO₅ inclusion was immersed in a CaO-SiO₂-Al₂O₃ molten slag for different durations at 1823 K. The Al₂TiO₅ dissolution paths and mechanism were revealed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Decreased amounts of Ti and Al and increased amounts of Si and Ca at the dissolution boundary prove that inclusion dissolution and slag penetration simultaneously occur. SiO₂ diffuses or penetrates the inclusion more quickly than CaO, as indicated by the w(CaO)/w(SiO₂) value in the reaction region. A liquid product (containing 0.7–1.2 w(CaO)/w(SiO₂), 15wt%–20wt% Al₂O₃, and 5wt%–15wt% TiO₂) forms on the inclusion surface when Al₂TiO₅ is dissolved in the slag. Al₂TiO₅ initially dissolves faster than the diffusion rate of the liquid product toward the bulk slag. With increasing reaction time, the boundary reaches its largest distance, the Al₂TiO₅ dissolution rate equals the liquid product diffusion rate, and the dissolution process remains stable until the inclusion is completely dissolved.     

Effects of metal binder on the microstructure and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-based micro-nanocomposite ceramic tool material

The Al₂O₃-(W,Ti)C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS). Mechanical properties such as flexural strength, fracture toughness, and Vickers hardness were also measured. Results show that the main phases Al₂O₃ and (W,Ti)C were detected by XRD. Compound MoNi also existed in sintered nanocomposites. The fracture modes of the nanocomposites were both intergranular and transgranular fractures. The plastic deformation of metal particles and crack bridging were the main toughening mechanisms. The maximum flexural strength and fracture toughness were obtained for 9vol% and 12vol% additions of Ni and Mo, respectively. The hardness of the composites reduced gradually with increasing content of metals Ni and Mo.     

Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.