Anomalies in mid-high-temperature linear thermal expansion coefficient of the closed-cell aluminum foam

Low-density closed-cell aluminum foam is promising to be used as load-bearing and thermal insulation components. It is necessary to systematically study its thermal expansion performance. In this work, linear thermal expansion coefficient(LTEC) of the closed-cell aluminum foam of different density was measured in the temperature range of 100–500 °C. X-ray fluorescence was used to analyze elemental composition of the cell wall material. Phase transition characteristics were analyzed with X-ray diffraction and differential scanning calorimetry. LTEC of the closed-cell aluminum foam was found to be dominated by its cell wall property and independent of its density. Particularly, two anomalies were found and experimentally analyzed. Due to the release of the residual tensile stress, the LTEC declined and even exhibited negative values. After several thermal cycles, the residual stress vanished. With temperature higher than 300 °C,instantaneous LTEC showed hysteresis, which should result from the redistribution of some residual hydrogen in the Ti2Al20 Ca lattice.     

Effect of equal channel angular pressing on aging treatment of Al-7075 alloy

The effect of aging treatment on microstructure and mechanical properties of equal channel angular pressed Al-7075 alloy was examined.Commercial Al-7075 alloy in the solid solution heat-treated condition was processed by equal channel angular pressing through route BCat both the room temperature and 120 1C. Only three passes of equal channel angular pressing was possible due to the low ductility of the alloy at both temperatures. Followed by equal channel angular pressing, the specimens have been aged at 120 1C for different aging times. Mechanical properties were measured by Vickers microhardness and tensile tests and microstructural observations were undertaken using transmission electron microscopy, X-ray diffractometer as well as optical microscopy. Microstructural investigations showed that ultrafine-grained materials with grain size in the range of 200–350 nm and 300–500 nm could be obtained after three passes of equal channel angular pressing at room temperature and 120 1C, respectively. Equal channel angular pressing of solid solution heat-treated Al-7075 alloy accelerates precipitation rate and subsequently leads to a significant decrease in aging time to attain maximum mechanical properties. Furthermore, it is possible to achieve maximum mechanical properties during equal channel angular pressing at 120 1C as a result of dynamic aging and formation of small η′ phase.     

Low-heating solid state synthetic reactions of cyclopeantadienyl organolanthanide complexes

A novel and simple one-step,solid state reaction of multicomponent systems has been developed to synthesize cyclopentadienyl-containing organolanthanide complexes,in which the effects of the coordinated solvent molecules and the nature of the reactants were also studied.We also studied the solid state decomposition reaction of Cp2 YbPz(HPz),and the formation of [CpYb(Pz)2|2 may indicate that the constrained environment in solid state can lead to a novel chemical transformation,with product selectivity possibly different from that in the liquid phase.     

DSC analyses of static and dynamic precipitation of an Al–Mg–Si–Cu aluminum alloy

In the present investigation, both static and dynamic precipitations of an Al–Mg–Si–Cu aluminum alloy after solid-solution treatment(SST)were comparatively analyzed using differential scanning calorimetry(DSC). Dynamic aging was performed in the SST alloy through equal channel angular pressing(ECAP) at different temperatures of room temperature, 110, 170, 191 and 300 1C. For comparison, static artificial aging was conducted in the SST alloy at 191 1C with two aging times of 4 and 10 h. The DSC analyses reveal that the dynamic precipitation has occurred in the ECAPed samples, while the activation energies associated with the strengthening precipitates in the dynamic samples are considerably higher than the energies in the SST and static aged samples. The higher activation energies are probably attributed to the smaller grains and higher dislocation density developed after ECAP. The results in the present investigation allow the prediction of the type of the dynamic precipitates to influence the strength of the ultrafine grained alloy during ECAP at various temperatures.     

Thermomechanical Behavior in Continuous Bloom Casting with Different Mold Tapers

A two-dimensional finite element model was used to analyze the thermal and mechanical behavior during solidification of the strand in a continuous bloom casting mold. The coupled heat transfer and deformation were analyzed to simulate the formation of the air gap between the mold and the strand. The model was used to investigate the influence of mold taper on the temperature and stress distributions in the strand. The results show that the air gap mainly forms around the strand corner, causing a hotter and thinner solidifying shell in this region. The mold taper partially compensates for the strand shell shrinkage and reduces the influence of the air gap on the heat transfer. The mold taper compresses the shell and changes the stress state around the strand corner region. As the strand moves down into the mold, the mold constraint causes compressive stress beneath the corner surface, which reduces the hot tear that forms on the strand.     

Microstructure evolution and thixoforming behavior of 7075 aluminum alloy in the semi-solid state prepared by RAP method

The effects of isothermal treatments on the microstructural evolution and coarsening rate of semi-solid 7075 aluminum alloy produced via the recrystallization and partial remelting (RAP) process were investigated. Samples of 7075 aluminum alloy were subjected to cold extrusion, and semi-solid treatment was carried out for 5–30 min at temperatures ranging from 580 to 605°C. A backward-extrusion experiment was conducted to investigate liquid segregation during the thixoforming process. The results revealed that obvious grain coarsening and spheroidization occurred during prolonged isothermal treatments. In addition, higher soaking temperatures promoted the spheroidization and coarsening process because of the increased liquid fraction and the melting of second phases. Segregation of the liquid phase caused by the difference in fluidity between the liquid and the solid phases was observed in different regions of the thixoformed specimens.     

Structure and corrosion resistance of Al–Cu–Fe alloys

The microstructure and electrochemical properties of Al–Cu–Fe alloys with the atomic compositions of Al_(65)Cu_(20)Fe_(15),Al_(78)Cu_7Fe_(15)and Al_(80)Cu_5Fe_(14)Si_1have been studied.The alloys were produced by induction melting of pure elements with copper mold casting.The microstructure of the alloys was analyzed by X-ray diffraction and high-resolution transmission electron microscopy.The formation of quasicrystalline phases in the Al–Cu–Fe alloys was confirmed.The presence of intermetallic phases was observed in the alloys after crystallization in a form of ingots and plates.The electrochemical measurements were conducted in 3.5%NaCl solution.The electronic structure of the alloys was determined by X-ray photoelectron spectroscopy.The post corrosion surface of the samples was checked using a scanning electron microscope equipped with the energydispersive X-ray detector.It was observed that the Al_(65)Cu_(20)Fe_(15)alloy had the highest corrosion resistance.The improved corrosion resistance parameters were noted for the plate samples rather than those in the as-cast state.And the hardness of the Al_(65)Cu_(20)Fe_(15)alloy was significantly higher than the other alloy samples.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

Morphology of α-Si3N4 in Fe–Si3N4 prepared via flash combustion

The state and formation mechanism ofα-Si3N4 in Fe–Si3N4 prepared by flash combustion were investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The results indicate thatα-Si3N4 crystals exist only in the Fe–Si3N4 dense areas. When FeSi75 particles react with N2, which generates substantial heat, a large number of Si solid particles evaporate. The prod-uct between Si gas and N2 is a mixture ofα-Si3N4 andβ-Si3N4. At the later stage of the flash combustion process,α-Si3N4 crystals dissolve and reprecipitate asβ-Si3N4 and theβ-Si3N4 crystals grow outward from the dense areas in the product pool. As the temperature decreases, the α-Si3N4 crystals cool before transforming into β-Si3N4 crystals in the dense areas of Fe–Si3N4. The phase composition of flash-combustion-synthesized Fe–Si3N4 is controllable through manipulation of the gas-phase reaction in the early stage and theα→βtrans-formation in the later stage.     

Slag formation path during dephosphorization process in a converter

The slag formation path is important for efficient dephosphorization in steelmaking processes. The phosphorus capacity and the melting properties of the slag are critical parameters for optimizing the slag formation path. Regarding these two factors, the phosphorus par-tition ratio was calculated using the regular solution model (RSM), whereas the liquidus diagrams of the slag systems were estimated using the FactSage thermodynamic package. A slag formation path that satisfies the different requirements of dephosphorization at different stages of dephosphorization in a converter was thus established through a combination of these two aspects. The composition of the initial slag was considered to be approximately 15wt%CaO–44wt%SiO2–41wt%FeO. During the dephosphorization process, a slag formation path that fol-lows a high-iron route would facilitate efficient dephosphorization. The composition of the final dephosphorization slag should be approxi-mately 53wt%CaO–25.5wt%SiO2–21.5wt%FeO. The composition of the final solid slag after dephosphorization is approximately 63.6wt%CaO–30.3wt%SiO2–6.1wt%FeO.     

Morphology of α-Si_3N_4 in Fe–Si_3N_4 prepared via flash combustion

The state and formation mechanism of α-Si3N4 in Fe–Si3N4 prepared by flash combustion were investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The results indicate that α-Si3N4 crystals exist only in the Fe–Si3N4 dense areas. When FeS i75 particles react with N2, which generates substantial heat, a large number of Si solid particles evaporate. The product between Si gas and N2 is a mixture of α-Si3N4 and β-Si3N4. At the later stage of the flash combustion process, α-Si3N4 crystals dissolve and reprecipitate as β-Si3N4 and the β-Si3N4 crystals grow outward from the dense areas in the product pool. As the temperature decreases, the α-Si3N4 crystals cool before transforming into β-Si3N4 crystals in the dense areas of Fe–Si3N4. The phase composition of flash-combustion-synthesized Fe–Si3N4 is controllable through manipulation of the gas-phase reaction in the early stage and the α→β transformation in the later stage.     

A Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous filler metal for improving the strength of Ti–6Al–4V alloy brazing joint

Ti_(50)Zr_(27)Cu_8Ni_4Co_3Fe_2Al_3Sn_3(at%) amorphous filler metal with low Cu and Ni contents in a melt-spun ribbon form was developed for improving mechanical properties of Ti–6Al–4V alloy brazing joint through decreasing brittle intermetallics in the braze zone. Investigation on the crystallization behavior of the multicomponent Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous alloy indicates the high stability of the supercooled liquid against crystallization that favors the formation of amorphous structure. The Ti–6Al–4V joint brazed with this Ti-based amorphous filler metal with low total content of Cu and Ni at 1203K for 900s mainly consists of α-Ti, β-Ti,minor Ti–Zr-rich phase and only a small amount of Ti_3Cu intermetallics, leading to the high shear strength of the joint of about 460 MPa. Multicomponent composition design of amorphous alloys is an effective way of tailoring filler metals for improving the joint strength.     

Influence of shielding gas on the mechanical and metallurgical properties of DP-GMA-welded 5083-H321 aluminum alloy

In the present research, 6-mm-thick 5083-H321 aluminum alloy was joined by the double-pulsed gas metal arc welding (DP-GMAW) process. The objective was to investigate the influence of the shielding gas composition on the microstructure and properties of GMA welds. A macrostructural study indicated that the addition of nitrogen and oxygen to the argon shielding gas resulted in better weld penetration. Furthermore, the tensile strength and bending strength of the welds were improved when oxygen and nitrogen (at concentrations as high as approximately 0.1vol%) were added to the shielding gas; however, these properties were adversely affected when the oxygen and nitrogen contents were increased further. This behavior was attributed to the formation of excessive brown and black oxide films on the bead surface, the formation of intermetallic compounds in the weld metal, and the formation of thicker oxide layers on the bead surface with increasing nitrogen and oxygen contents in the argon-based shielding gas. Analysis by energy-dispersive X-ray spectroscopy revealed that most of these compounds are nitrides or oxides.     

Microstructural morphology of semi-solid high carbon steel T12 before and after rheo-rolling

The semi-solid high carbon steel T 12 was rolled in closed box groove under a certain condition by the rheo-rolling equipment developed by our research group, and the microstructural morphology of semi-solid T12 before and after deformation was investigated by optical microscope in order to analysis and summarize the microstructure evolution law of T 12 deformed in semi-solid state. The experiments results show that the grains shape before deformation of semi-solid T12 steel display globule or ellipse by the electromagnetic stirring, the distribution of solid and liquid phase is homogeneous, but the microstructure of semi-solid product after rheo-rolling exhibits macrosegregation that distribution of liquid and solid phases changes, the liquid phases divorce from the solid phases, most of solid phases get together in the center of the specimen and liquid phases flow to the surface or the edge of the specimen, the grains occur plastic deformation while reduction increased in transact. The middle microstructure is more homogeneous than head or tail position in longitudinal direction, the head microstructure is similar to the tail and the size of grain is not homogeneous.     

Acting mechanism of F,K,and Na in the solid phase sintering reaction of the Baiyunebo iron ore

<正>The effect of F,K,and Na on the solid phase reaction of the Baiyunebo iron ore was investigated by differential thermal analysis (DTA) and X-ray diffraction(XRD).It has been identified that alkaline elements K and Na in the Baiyunebo ore instigate the formation of low melting point compounds Na_2SiO_3 and Na_2O·Fe_2O_3 and the generation of molten state in the solid phase sintering.Element F in the Baiyunebo ore facilitates the formation of cuspidine compound 3CaO·2SiO_2·CaF_2 in the solid phase reaction.The cuspidine compound is kept in solid as one of the final products through the entire sintering process due to its high melting point.In the sintering process,CaF_2and SiO_2 react with CaO first and form 3CaO·2SiO_2·CaF_2 and 3CaO·2SiO_2,so the formation of ferrites,Na_2O·Fe_2O_3,and 2CaO·Fe_2O_3 is inhibited.     

Microstructural morphology of the semi-solid high carbon steel T12 before and after rheo-rolling

The semi-solid high carbon steel T12 was rolled in a closed box groove under a certain condition by the rheo-rolling equipment, and the microstructural morphology of the semi-solid T12 before and after deformation was investigated by optical microscope to analyze and summarize the microstructure evolution law of T12 deformed in semi-solid state. The experiment results show that the grain shape before deformation of the semi-solid T12 steel displays globule or ellipse by the electromagnetic stirring, the distribution of solid and liquid phases is homogeneous. But the microstructure of semi-solid product after rheo-rolling exhibits macrosegregation that the distribution of liquid and solid phases changes, the liquid phases divorce from the solid phases. In the transverse section, most of the solid phases get together in the center of the specimen, the liquid phases flow to the surface or the edge of the specimen, and the grains occur plastic deformation while reduction increased. In longitudinal section, the middle microstructure of the specimen is more homogeneous than that at the head or tail, the head microstructure is similar to the tail and the size of the grains is not homogeneous.     

Cyclic oxidation behavior of b-NiAlDy alloys containing varying aluminum content at 1200 1C

b-NiAlDy cast alloys containing varying aluminum content were prepared by arcmelting. The microstructures and cyclic oxidation behavior of the alloys at 1200 1C were investigated. Grain refinement was achieved by increasing aluminum content in the alloy, which is beneficial to selective oxidation. The Ni–55Al–0.1Dy alloy showed excellent cyclic oxidation resistance due to the formation of a continuous, dense and slow-growing oxide scale. In contrast to this, severe internal oxidation as well as large void formation at the scale/alloy interface occurred in the Ni–45Al–0.1Dy alloy. The aluminum content dependence of the reactive element effects in b- NiAlDy was established that Dy doping strengthened the scale/alloy interface by pegging mechanism in high-aluminum alloys but accelerated internal oxidation in low-aluminum alloys during high-temperature exposure.     

Velocity Distribution of Slurry in Horizontal Pipe When Solid Particles Sliding

Based on the laws of momentum conservation and impulse in accelerating process, the distribution on speed of ununiform slurry flow in a horizontal pipe was studied. According to the momentum change of solid particles and conveying liquid of slurry flow during accelerating, and some effect factors, the relationship between the speed of solid particles and the speed of conveying liquid was obtained.When dealing with the friction between sliding solid particles and pipe, it is pivotal to reasonably distribute component of friction to each solid particle. The friction coefficient between solid particles was obtained by forces analysis and theoretic calculation, and can be used to calculate the friction force on every solid particle. The effect of friction on speed of ever), solid particle was investigated through the impulse law. The result is more accurate than that by using uniform friction on solid particles. It is completely new method to use above theory to get solid particles speed distribution, conveying liquid speed distribution and slurry speed distribution.     

Microstructural and mechanical characteristics of Al-alloyed ductile iron upon casting and annealing

Ductile iron containing 6.16wt% Al was developed to investigate the effects of aluminum on both its microstructure and hardness. It was found that aluminum not only increases the nodule count and pearlite content but also improves the hardness in both sand mold and metal mold castings. Annealing treatments were conducted to attain a homogenous microstructure and improve high-temperature serviceability. A ferrite/carbide or ferritic matrix was gained depending on the annealing temperature. It is also discovered that annealing has inverse influences on the hardness of the bulk alloy and the ferrite phase. Although it causes a small decrease in the bulk hardness of the specimens, it leads to an increase in the microhardness of the ferrite. Micro-segregation of the alloying elements was also investigated by means of electron probe micro-analysis for the specimens with different annealing durations and the as-cast specimen as well. An optimum annealing time was proposed to result in the least amount of micro-segregation of aluminum and silicon between graphite nodules.     

Immersing Treatment of Steel Plate Surface in Steel-Aluminum Solid to Liquid Bonding

The interfacial status of the steel-aluminum solid to liquid bonding plates (their steel plate surfaces were or were not immersed in flux aqueous solution) were measured by using SEM (Scanning Electron Microscope) and X-ray diffraction. The results showed that the layer of flux (the minimum thickness was 15 μm on the steel plate surface) could protect the steel plate surface from oxidizing effectively at high temperature in solid to liquid bonding. The melt temperatUre of the flux should be lower than 580 ℃ so that it could be melted and removed completely. No. 1 flux (patent product made by the author) made up of halogeindes could also force liquid aluminum to infiltrate into steel plate surface and thus the interfacial shear strength of the bonding plate was rather large.