Effects of Sn addition on microstructure and mechanical properties of Mg- Zn-Al alloys

The effects of Sn addition(0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in cast and extruded states were investigated, and the mechanical properties of as-extruded Mg-4Zn-1.5Al-xSn studied. The experimental results showed that the as-cast Mg-4Zn-1.5Al alloy was composed of two phases α-Mg and Mg_(32)(Al, Zn)_(49), while Sn-containing alloys consisted of α-Mg, Mg_(32)(Al, Zn)_(49) and Mg_2Sn phases, and Mg_(32)(Al, Zn)_(49) was not detected after extruding due to that the most of them dissolved into the matrix during the homogenized treatment. The addition of Sn refined the grains of as-cast and as-extruded Mg-Zn-Al alloys obviously. It was noted that the basal texture intensity reduced with increasing Sn content significantly in as-extruded Mg-Zn-Al alloys. The tensile tests results indicated that Sn addition improve the tensile strength of the extruded alloys,while it had a harmful effect on the ductility. When the addition of Sn was 2 wt%, the ultimate tensile strength(UTS), yield strength(YS) and elongation(ε_f) of the alloy were 280 MPa, 147 MPa and 17.4%, respectively.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Microstructure, mechanical and thermo-physical properties of hot-pressed Al2O3-GdAlO3-ZrO2 ceramics with eutectic composition

A low cost chemical co-precipitation method was employed to fabricate nanoscale Al_2O_3-GdAlO_3-ZrO_2 powder with eutectic composition. A careful control of reaction conditions was required during the preparation. The synthesized nanopowders exhibited a particle size of 20-200 nm, and were highly dispersive and uniform. The results showed that calcination temperature had an important influence on the phase constituents of the nanopowders. With increasing the calcination temperature, a phase transformation from θ-Al_2O_3 to α-Al_2O_3 and a thermal decomposition from Gd_3 Al_5O_(12)(GdAG) to GdAlO_3 and α-Al_2O_3 occurred in sequence. A calcination temperature of 1300 ℃ was needed for the crystallization of α-Al_2 O_3. These nanosized powders were consolidated via hot pressing to produce a fully densified ceramic composite with eutectic composition. The Al_2O_3-GdAlO_3-ZrO_2 ceramic hot-pressed at 1500 ℃ exhibited a relative density of 99.4%, a flexural strength of 485 MPa and a fracture toughness of 6.5 MPa m~(1/2). The ceramic had a thermal conductivity of 1.9 W m K~(-1) at 1200 ℃ and a thermal expansion coefficient of 9.49 ×10~(-6) K~(-1) at 1100 ℃.     

Facile synthesis of nanosized sodium magnesium hydride, NaMgH3

The ternary magnesium hydride NaMgH 3 has been synthesised via reactive milling techniques.The method employed neither a reactive H2 atmosphere nor high pressure sintering or other post-treatment processes.The formation of the ternary hydride was studied as a function of milling time and ball:powder ratio.High purity NaMgH 3 powder(orthorhombic space group Pnma,a 5.437(2),b 7.705(5),c 5.477(2) ;Z 4) was prepared in 5 h at high ball:powder ratios and characterised by powder X-ray diffraction(PXD),Raman spectroscopy and scanning electron microscopy/energy dispersive X-ray spectroscopy(SEM/EDX).The products formed sub-micron scale(typically 200-400 nm in size) crystallites that were approximately isotropic in shape.The dehydrogenation behaviour of the ternary hydride was investigated by temperature programmed desorption(TPD).The nanostructured hydride releases hydrogen in two steps with an onset temperature for the first step of 513 K.     

Rapid solidification mechanism of Ag60Sb34Cu6 ternary alloy in drop tube

Ternary eutectic growth involves competitive nu-cleation and growth of three solids from one liquid. Thesolidification behavior of ternary eutectic alloy is morecomplex than that of binary eutectic alloy due to the addi-tion of the third component[1—4]. Up to now, most scientificinvestigations on ternary eutectic alloy focus on the influ-ence of changing the component or adding a fourth even afifth element on the performance of the alloy[5—8]. How-ever, the information on crystal growth char…     

MgCo2-D2 and MgCoNi-D2 systems synthesized at high pressures and interaction mechanism during the HDDR processing

MgCo_2 and MgNiCo crystallize with hexagonal Laves type intermetallic structures of the C14 type and do not form hydrides at ambient hydrogen pressures. However, applying high hydrogen pressures in the GPa range forces the hydrogen absorption and leads to the formation of multi-phase compositions, which contain approximately 2.5 atoms H per formula unit of MgCo_2 or MgNiCo and remain thermally stable under normal conditions.The hydrogenation of MgCo_2 resulted in its decomposition to a ternary Mg_2CoD_5 deuteride and metallic cobalt. Phase-structural transformations accompanying the vacuum desorption of deuterium in the temperature range of 27–500 °C were studied using in situ neutron powder diffraction. The investigation showed a complete recovery of the initial MgCo_2 intermetallic via a Hydrogenation-Disproportionation-Desorption-Recombination process. At 300°C, the Mg_2CoD_5 deuteride first decomposed to elementary Mg and hexagonal Co. At 400°C, a MgCo phase was formed by interaction between Mg and Co. At the highest processing temperature of 500°C, a solid-state interaction of MgCo and Co resulted in the recovery of the initial MgCo_2.The interaction of MgNiCo with deuterium under the synthesis conditions of 2.8 GPa and 200 °C proceeded in a more complex way. A very stable ternary deuteride MgNi_2D_3 was leached away while Co was separated in the form of Mg_2CoD_5 and the remaining nickel formed a solid solution with Co with the approximate composition Ni_(0.7)Co_(0.3).The thermal desorption of deuterium from MgCo_2D_(2.5) and from MgNiCoD_(2.5) has been studied by Thermal Desorption Spectroscopy with deuterium released into a closed volume. The observed effects nicely correlate with changes in the phase structural composition of the hydrides formed.MgCo_2 is a new example of the hydrogen storage alloy, in which a successful HDDR processing results in the reversible formation of the initial intermetallic at much lower temperatures than in the equilibrium phase diagram of the Mg-Co system.     

Joining of Si3N4 ceramic using PdCo(Ni SiB)–V system brazingfi ller alloy and interfacial reactions

The wettability of V-active PdCo-based alloys on Si3N4ceramic was studied with the sessile drop method. And the alloy of Pd50.0–Co33.7–Ni4.0–Si2.0–B0.7–V9.6(wt%),was developed for Si3N4ceramic joining in the present investigation. The rapidly-solidified brazing foils were fabricated by the alloy Pd50.0–Co33.7–Ni4.0–Si2.0–B0.7–V9.6. The average room-temperature three-point bend strength of the Si3N4/Si3N4joints brazed at 1453 K for 10 min was 205.6 MPa,and the newly developed braze gives joint strengths of 210.9 MPa,206.6 MPa and 80.2 MPa at high temperatures of 973 K,1073 K and 1173 K respectively. The interfacial reaction products in the Si3N4/Si3N4joint brazed at 1453 K for10 min were identified to be VN and Pd2Si by XRD analysis. Based on the XEDS analysis result,the residual brazing alloy existing at the central part of the joint was verified as Co-rich phases,in which the concentration of element Pd was high up to 18.0–19.1 at%. The mechanism of the interfacial reactions was discussed. Pd should be a good choice as useful alloying element in newer high-temperature braze candidates for the joining of Si-based ceramics.     

Densification behavior of mechanically milled Cu–8 at% Cr alloy and its mechanical and electrical properties

Synthesis and consolidation behavior of Cu–8 at%Cr alloy powders made by mechanical alloying with elemental Cu and Cr powders,and subsequently,compressive and electrical properties of the consolidated alloys were studied.Solid solubility of Cr in Cu during milling,and subsequent phase transformations during sintering and heat treatment of sintered components were analyzed using X-ray diffraction,scanning electron microscopy and transmission electron microscopy.The milled powders were compacted applying three different pressures(200 MPa,400 MPa and 600 MPa)and sintered in H2atmosphere at 900 1C for 30 min and at 1000 1C for 1 h and 2 h.The maximum densification(92.8%)was achieved for the sample compacted at 600 MPa and sintered for 1000 1C for 2 h.Hardness and densification behavior further increased for the compacts sintered at 900 1C for 30 min after rolling and annealing process.TEM investigation of the sintered compacts revealed the bimodal distribution of Cu grains with nano-sized Cr and Cr2O3precipitation along the grain boundary as well as in grain interior.Pinning of grain boundaries by the precipitates stabilized the fine grain structure in bimodal distribution.     

Corrosion study of resorbable Ca60Mg15Zn25 bulk metallic glasses in physiological fluids

The corrosion activity of amorphous plates of Ca_(60)Mg_(15)Zn_(25)alloy was investigated.The biocompatible elements were selected for the alloy composition.The electrochemical corrosion and immersion tests were carried out in a multi-electrolyte fluid and Ringer's solution.Better corrosion behavior was observed for the samples tested in a multi-electrolyte fluid despite the active dissolution of Ca and Mg in Ringer's solution.The experimental results indicated that reducing concentration of NaCl from 8.6 g/dm~3for Ringer's solution to 5.75 g/dm~3caused the decrease of the corrosion rate.The volume of the hydrogen evolved after 480 min in Ringer's solution(40.1 ml/cm~2)was higher in comparison with that obtained in a multi-electrolyte fluid(24.4 ml/cm~2).The values of opencircuit potential(E_(OCP))for the Ca_(60)Mg_(15)Zn_(25)glass after 1 h incubation in Ringer's solution and a multielectrolyte fluid were determined to be-1553 and-1536 m V vs.a saturated calomel electrode(SCE).The electrochemical measurements indicated a shift of the corrosion current density(j_(corr))from 1062μA/cm~2for the sample tested in Ringer's solution to 788μA/cm~2for the specimen immersed in a multi-electrolyte fluid.The corrosion products analysis was conducted by using the X-ray photoelectron spectroscopy(XPS).The corrosion products were identified to be CaCO_3,Mg(OH)_2,CaO,MgO and Zn O.The mechanism of corrosion process was proposed and described based on the microscopic observations.The X-ray diffraction and Fourier transform infrared spectroscopy(FTIR)also indicated that Ca(OH)_2,CaCO_3,Zn(OH)_2and Ca(Zn(OH)_3)_2·2H_2O mainly formed on the surface of the studied alloy.     

Wear properties of NiAl based materials

The NiAl based materials including NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite were fabricated and their wear properties were tested at different temperatures.The results revealed that the NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite exhibited the excellent wear properties between 700℃ and 900℃.The microstructure observations exhibited that the self-lubricant films formed on the worn surfaces during the dry sliding test at high temperature,which decreased the wear rate and friction coefficient significantly.TEM observation on the self-lubricant film revealed that it was mainly comprised by ceramic amorphous and nanocrystalline.Compared with the NiAl-TiC-Al2O3 composite,the NiAl-Cr(Mo)-CrxSy in situ composite has lower friction coefficient at low temperature.Such phenomena may be ascribed to the addition of sulfide which contributes much to the formation of self-lubricant,and moreover the TiC addition increase the strength of NiAl based material and its wear resistance.     

Abnormal thermal shock behavior in electrical conductivity of Ti2SnC

Some ternary carbide and nitride ceramics have been demonstrated to exhibit abnormal thermal shock behavior in mechanical properties. However, the influence of thermal shock on other properties is not clear. This work reports on the influence of thermal shock on electrical conductivity of Ti_2SnC as a representative member of ternary carbides. Abnormal change in electrical conductivity was first demonstrated during quenching Ti_2 SnC in water at 500-800 ℃. The residual electrical conductivity of the quenched Ti_2SnC gradually decreased with increasing temperature, but abnormally increased after quenching at 600 ℃. The microstructure of surface cracks was characterized. The main mechanism for the abnormal electrical conductivity recovery is that some narrow branching cracks are filled by metallic Sn precipitating from Ti_2SnC.     

Preparation and catalytic effect of porous Co3O4 on the hydrogen storage properties of a Li-B-N-H system

A porous Co_3O_4 with a particle size of 1–3 μm was successfully prepared by heating Co-based metal organic frameworks MOF-74(Co) up to 500 °C in air atmospheric conditions. The as-prepared porous Co_3O_4 significantly reduced the dehydrogenation temperatures of the LiBH_4-2LiNH_2 system and improved the purity of the released hydrogen. The LiBH_4-2LiNH_2-0.05/3Co_3O_4 sample started to release hydrogen at 140 °C and released hydrogen levels of approximately 9.7 wt% at 225 °C. The end temperature for hydrogen release was lowered by 125 °C relative to that of the pristine sample. Structural analyses revealed that the as-prepared porous Co_3O_4 is in-situ reduced to metallic Co, which functions as an active catalyst, reducing the kinetic barriers and lowering the dehydrogenation temperatures of the LiBH_4-2LiNH_2 system. More importantly, the porous Co_3O_4-containing sample exhibited partially improved reversibility for hydrogen storage in the LiBH_4-2LiNH_2 system.     

Zr-pillared montmoril lonite supported cobalt nanoparticles for Fischer – Tropsch synthesis

In this article Fischer–Tropsch(FT) synthesis was studied over cobalt nanoparticles supported on modifed Montmorillonite(Zr-PILC).Co-loaded/Zr-PILC catalysts were synthesized by hydrothermal methods and were characterized by XRD,XRF,BET,H2-TPR,TGA and SEM techniques.FT reactions were carried out in fxed bed microreactor(T 225 1C,260 1C and 275 1C,P 1,5 and 10 bars).The FT-products obtained over Co-loaded/Zr-PILC catalysts showed increased selectivity of C2–C12hydrocarbons and decreased selectivity towards CH4and higher molecular weight hydrocarbons(C21) at a TOS of 2–30 h as compared to the Co-loaded/NaMMT catalysts.With increase in reaction temperature from225 1C to 275 1C,CO-conversion and CH4selectivity increases while that of C5+hydrocarbons decreases.Decrease in CH4selectivity while increase in C5+hydrocarbons and CO-conversion were observed on increasing the pressure of reaction.     

Microstructure and growth kinetics of Ce and Y jointly modified silicide coatings for Nb–Ti–Si based ultrahigh temperature alloy

In order to protect Nb-Ti-Si based ultrahigh temperature alloy from oxidation, pack cementation processes were utilized to prepare Ce and Y jointly modified silicide coatings. The Ce and Y jointly modified silicide coating has a double-layer structure: a relatively thick (Nb, X)Si2 (X represents Ti, Cr and Hf elements) outer layer and a thin (Ti, Nb)5Si4 transitional layer. The pack cementation experiments at 1150 ℃ for 8 h proved that the addition of certain amounts of CeO2 and Y2O3 powders in the packs distinctly influenced the coating thickness, the contents of Si, Ce and Y in the (Nb, X)Si2 outer layers, and the density of cavities in the coatings. In order to study the effects of Ce and Y joint modification in the silicide coatings, both only Ce and only Y modified silicide coatings were also prepared for comparison. The mechanisms of the beneficial effects of Ce and Y are discussed. A pack mixture containing 1.5CeO2-0.75Y2O3 (wt%) powders was employed to investigate the growth kinetics of the Ce and Y jointly modified silicide coating at 1050, 1150 and 1250 ℃. It has been found that the growth kinetics obeyed parabolic laws and the parabolic rate constants were 109.20 mm2/h at 1050 ℃, 366.75 mm2/h at 1150 ℃ and 569.78 mm2/h at 1250 ℃, and the activation energy for the growth of the Ce and Y jointly modified silicide coating was 197.53 kJ/mol.     

Rapid solidification of acoustically levitated Al-Cu-Si eutectic alloy under laser irradiation

Al-27%Cu-5.3%Si ternary eutectic alloy was melted using a YAG laser and then solidified while being acoustically levitated. A maximum undercooling to 195 K (0.24 TL) was achieved with a cooling rate of 76 K/s. The solidification microstructure was composed of (Al+θ+Si) ternary eutectics and (Al+θ) pseudobinary eutectics. During acoustic levitation, the (Al+θ+Si) ternary eutectics are refined and the (Al+θ) pseudobinary eutectics have morphological diversity. On the surface of the alloys, surface oscillations and acoustic streaming promote the nucleation of the three eutectic phases and expedite the cooling process. This results in the refinement of the ternary eutectic microstructure. During experiments, the reflector decreases with increasing alloy temperature, and the levitation distance always exceeds the resonant distance. Because of the acoustic radiation pressure, the melted alloy was flattened, and deformation increases with increasing sound pressure. The maximum aspect ratio achieved was 6.64, corresponding to a sound pressure of 1.8×104 Pa.     

Activated carbon derived from rice husk by NaOH activation and its application in supercapacitor

Four activated carbon(AC) samples prepared from rice husk under different activation temperatures have been characterized by N2adsorption–desorption isotherms, thermogravimetric analysis(TGA–DTA), Fourier transform infrared spectroscopy(FTIR) and scanning electron microscopy(SEM). The specific surface area of AC sample reached 2681 m2 g 1under activation temperature of 800 1C. The AC samples were then tested as electrode material; the specific capacitance of the as-prepared activated carbon electrode was found to be 172.3 F g 1using cyclic voltammetry at a scan rate of 5 mV s 1and 198.4 F g 1at current density 1000 mA g 1in the charge/discharge mode.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

DC-bias and visible light effect on dielectric characteristics of La_(0.5)Cr_(0.5)TiO_(3+δ)

La_(0.5)Cr_(0.5)TiO_(3+δ) ceramic sample was prepared via traditional solid-state reaction route. Frequency and temperature dependence of dielectric permittivity were studied in the range of 10~2~ 10~6 Hz and of 77 ~360 K, respectively. It was observed that extraordinarily high low-frequency dielectric constants appeared at room temperature, and dielectric relaxation peaks shifted to higher temperature with increasing frequency. In the dc-bias studies, it was also found that the dielectric permittivity had obviously dc-bias dependence in low frequency, but independence as the frequency above 14 kHz. Interestingly, the dielectric characteristics of the sample had obvious light dependence at room temperature within the measured frequency range. The results demonstrate that visible light improves the dielectric properties of the ceramic by means of I–V and complex impedance analysis.     

Phase analysis of AlFe2B2 by synchrotron X-ray diffraction, magnetic and Mössbauer studies

The structural and magnetic properties of essentially phase pure AlFe_2B_2 prepared by arc melting were compared with a sample containing impurities. Analysis was carried out by means of synchrotron X-ray diffraction, magnetic measurements and M?ssbauer spectroscopy. The analysis of synchrotron X-ray diffraction data confirmed the orthorhombic structure of space group Cmmm for AlFe_2B_2 with Al_(13)Fe_4 as main impurity phase. The magnetic measurements revealed an unsaturated ferromagnetic state in AlFe_2B_2 with a transition temperature(T_c) of 286 K. Isothermal magnetization measurment at 5 K gave a saturation magnetization of 0.7 μB per Fe atom while Arrott plots establish the second order nature of ferromagnetic transition. The thermal evolution of M?ssbauer spectra confirmed the ferromagnetic nature of this material revealing an hyperfine field of 73 kOe and an isomer shift of 0.46 mm/s at 100 K. The M?ssbauer spectra of a phase pure sample was compared with the one containing impurity phases. It is suggested that the low temperature paramagnetic contribution in M?ssbauer spectra of phase pure material may have its origin in some intrinsic phenomena arising from defects or inhomogeneities in crystal structure.     

Effect of B2O3 on the aqueous tape casting and microwave properties of Li2O–Nb2O5–TiO2 ceramics

The effect of B2O3 addition on the aqueous tape casting, sintering, microstructure and microwave dielectric properties of Li2O-Nb2O5-TiO2 ceramics has been investigated. The tape casting slurries exhibit a typical shear-thinning behavior without thixotropy, but the addition of B2O3 increases the viscosity of the slurries significantly. It was found that doping of B2O3 can decrease the tensile strength, strain to failure and density of the green tapes. The sintering temperature could be lowed down to 900℃ with the addition of 2 wt% B2O3 due to the liquid phase effect. No secondary phase is observed. The addition of B2O3 does not induce much degradation on the microwave dielectric properties. Optimum microwave dielectric properties of εr 67, Q×f 6560 GHz are obtained for Li2O-Nb2O5-TiO2 ceramics containing 2 wt% B2O3 sintered at 900 1C. It represents that the ceramics could be promising for multilayer low-temperature co-fired ceramics (LTCC) application.