The giant magnetocaloric effect in Gd<Subscript>5</Subscript>Si<Subscript>2</Subscript>Ge<Subscript>2</Subscript> with low purity gadolinium

The giant magnetocaloric effect Gd5Si2Ge2 alloy was prepared with 99wt% low purity commercial Gd. Powder XRD and magnetic measurements showed that the Gd5Si2Ge2 alloy annealed at 1200℃ for 1h had a significant magnetic- crystallographic first order phase transition at about 270 K. The maximal magnetic entropy change is 17.55 J· kg^-1· K^-1 under a magnetic field change of 0-5 T. The distinct increase of magnetic entropy change belongs to the first-order phase transition from the orthorhombic Gd5Si4-type to the monoclinic Gd5Si2Ge2-type after high temperature heat-treatment.     

Magnetic refrigeration materials

Magnetic refrigeration has drawn much attention because of its greater efficiency and higher reliability than the traditional gas-cycle refrigeration technology. Recently, a kind of new materials with a giant magnetocaloric effect in the subroom temperature range, Gd5 (Six Ge1- x)4, was discovered, which boosts the search for high-performance magnetic refrigerants. However, the intermetallic compounds Gd5 (SixGe1 - x )4 belong to the first order transition materials; their performance in practical magnetic refrigeration cycles remains controversial. In this paper the developing tendency of the refrigerants are discussed on the basis of our work.     

Bulk amorphous Al_（85）Ni_（10）Ce_5 composite fabricated by cold hydromechanical pressing of partially amorphous powders

Gas atomized Al85Ni10Ce5 partially amorphous alloy powders were successfully consolidated into bulk alloy specimens with high relative density at room temperature by cold hydromechanical pressing. The consolidated specimens have a high fracture strength of up to 1.1 GPa. Two densification mechanisms are proposed to explain the consolidation process. The viscous flow of the amorphous phase because of local heating facilities the elimination of residual pores.     

Primary dendrite growth of Ni<Subscript>3</Subscript>Sn intermetallic compound during rapid solidification of undercooled Ni-Sn-Ge alloy

Liquid Ni-31.7%Sn-2.5%Ge alloy was highly undercooled by up to 238 K(0.17TL) with glass fluxing and drop tube techniques.The dendritic growth velocity of primary Ni3Sn compound shows a power-law relation to undercooling and achieves a maximum velocity of 380 mm/s.The addition of Ge reduces its growth velocity as compared with the binary Ni75Sn25 alloy.A structural transition from coarse dendrites into equiaxed grains occurs once undercooling exceeds a critical value of about 125 K,which is accompanied by both grain refinement and solute trapping.The Ni3Sn intermetallic compound behaves like a normal solid solution phase showing nonfaceted growth during rapid solidification.     

The evolution of microstructure and mechanical properties during high-speed direct-chill casting in different Al-Mg2Si in situ composites

The effect of high-speed direct-chill (DC) casting on the microstructure and mechanical properties of Al-Mg₂Si in situ composites and AA6061 alloy was investigated. The microstructural evolution of the Al-Mg₂Si composites and AA6061 alloy was examined by optical microscopy, field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The results revealed that an increase of the casting speed substantially refined the primary Mg₂Si particles (from 28 to 12 μm), the spacing of eutectic Mg₂Si (from 3 to 0.5 μm), and the grains of AA6061 alloy (from 102 to 22 μm). The morphology of the eutectic Mg₂Si transformed from lamellar to rod-like and fibrous with increasing casting speed. The tensile tests showed that the yield strength, tensile strength, and elongation improved at higher casting speeds because of refinement of the Mg₂Si phase and the grains in the Al-Mg₂Si composites and the AA6061 alloy. High-speed DC casting is demonstrated to be an effective method to improve the mechanical properties of Al-Mg₂Si composites and AA6061 alloy billets.     

Transition-metal-based magnetic refrigerants for room-temperature applications.

Magnetic refrigeration techniques based on the magnetocaloric effect (MCE) have recently been demonstrated as a promising alternative to conventional vapour-cycle refrigeration. In a material displaying the MCE, the alignment of randomly oriented magnetic moments by an external magnetic field results in heating. This heat can then be removed from the MCE material to the ambient atmosphere by heat transfer. If the magnetic field is subsequently turned off, the magnetic moments randomize again, which leads to cooling of the material below the ambient temperature. Here we report the discovery of a large magnetic entropy change in MnFeP0.45As0.55, a material that has a Curie temperature of about 300 K and which allows magnetic refrigeration at room temperature. The magnetic entropy changes reach values of 14.5 J K-1 kg-1 and 18 J K-1 kg-1 for field changes of 2 T and 5 T, respectively. The so-called giant-MCE material Gd5Ge2Si2 (ref. 2) displays similar entropy changes, but can only be used below room temperature. The refrigerant capacity of our material is also significantly greater than that of Gd (ref. 3). The large entropy change is attributed to a field-induced first-order phase transition enhancing the effect of the applied magnetic field.     

Synthesis and Magnetic Properties of Spin-Liquid Tb2Ti2O7

Polycrystalline samples of a novel spin-liquid compound Tb2Ti2O7 were prepared by a standard solid-state reaction. X-ray diffraction at room temperature confirms that the synthesized compound of Tb2Ti2O7 is single phase with cubic unit cell constant a0 of 1.015 44 nm. Magnetic susceptibility measurements in the temperature range between 100 and 300 K give an effective moment of 9.44 μB and Curie-Weiss temperature of 12.68 K, respectively, indicating the dominance of antiferromagnetic interactions. However, below 50 K, the magnetic behavior of Tb2Ti2O7 deviates from Curie-Weiss law, whose origin remains suspicion.     

Formation of ζ phase in Cu-Ge peritectic alloys

Rapid growth behavior of ζ phase has been investigated in the undercooling experiments of Cu-14%Ge, Cu-15%Ge, Cu-18.5%Ge and Cu-22%Ge alloys. Alloys of the four compositions obtain the maximum undercoolings of 202 K（0.17TL）, 245 K（0.20TL）, 223 K（0.20TL） and 176 K（0.17TL）, respectively. As the content of Ge increases, the microstructural transition of ＂a（Cu） dendrite ＋ ζ＂ peritectic phase → ζ＂ peritectic phase →, ζ dendrite ＋ （ε＋ζ） eutectic＂ takes place in the alloy at small undercooling, while the microstructural transition of ＂fragmented α （Cu）dendrite ＋ ζ peritectic phase →, ζ peritectic phase →ζ dendrite ＋ ε phase＂ happens in the alloy at large undercooling. EDS analysis of the Ge content in peritectic phase indicates that undercooling enlarges the solid solubility of ζ rdendrite, which leads to a decrease in the Ge content in ζ phase as undercooling increases. In the Cu-18.5%Ge alloy composed of ζ peritectic phase, the Ge content in ζ phase increases when undercooling increases, which is due to the restraint of the Ge enrichment on the grain boundaries by high undercooling effect.     

Work toughening effect in Zr_（41）Ti_（14）Cu_（12.5）Ni_（10）Be_（22.5） bulk metallic glass

Work hardening is a well-known phenomenon occurring in crystalline metals during deformation,which has been widely used to increase the strength of metals although their ductility is usually reduced simultaneously. Here we report that the plastic strain of Zr41Ti14Cu12.5Ni10Be22.5 (at.%) bulk metallic glasses has been increased from 0.3% for the as-cast sample to 2.5%-8.0% for samples that have experienced pre-deformation under constrained conditions. The pre-deformed glassy alloys possess more free volume and abundant introduced shear bands,which are believed to promote the activation of shear bands in post-deformation and result in an increase in plasticity. The orientation of the pre-introduced shear bands relative to the loading direction will affect the deformation behavior of pre-deformed samples. The present results show that pre-deformation of this glassy alloy will result in work toughening. This work toughening effect can be removed by isothermal annealing at a sub-Tg (glass transition) temperature,which causes annihilation of free volume and healing of shear bands.     

Polysaccharide separation mechanism in polysulfone-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic composite membranes

Polysulfone (PSF)-Fe3O4 composite membranes were prepared by the phase-inversion process and their polysaccharide separation mechanism was explored using chondroitin sulfate (CS) and dextran. The mechanism was analyzed from constraints on the magnetic field and geometric deformation. It was found that variations in dextran rejection from 58% to 46% were mainly influenced by the geometric deformation of the composite membrane, while the magnetic field had a significant influence on variations in CS rejection from 82% to 35%. The results indicate that it is possible to continuously separate different types of polysaccharide with a composite membrane by adjusting the external magnetic field.     

Luminescent research of Sr5（PO4）3Cl：Eu^2＋ blue phosphor used for electron beam excitation

Eu^2 -aetivated strontium choloro-phosphate has been used for lamp phosphor traditionally with high efficiency. In this paper, the cathodoluminescent properties of Sr5(PO4)3Cl：Eu^2 have been investigated for application in field emission display. The influence of Ba^2 , Ca^2 impurities on the cathodoluminescent spectrum of Sr5(PO4)3Cl:Eu^2 has also been measured. When operate voltage varied from mid- to low-voltage, the relative brightness and saturation behavior of phosphor was observed at different current density.     

Dissolution of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript> inclusions in CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags at 1823 K

Al-Ti-O inclusions always clog submerged nozzles in Ti-bearing Al-killed steel. A typical synthesized Al₂TiO₅ inclusion was immersed in a CaO-SiO₂-Al₂O₃ molten slag for different durations at 1823 K. The Al₂TiO₅ dissolution paths and mechanism were revealed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Decreased amounts of Ti and Al and increased amounts of Si and Ca at the dissolution boundary prove that inclusion dissolution and slag penetration simultaneously occur. SiO₂ diffuses or penetrates the inclusion more quickly than CaO, as indicated by the w(CaO)/w(SiO₂) value in the reaction region. A liquid product (containing 0.7–1.2 w(CaO)/w(SiO₂), 15wt%–20wt% Al₂O₃, and 5wt%–15wt% TiO₂) forms on the inclusion surface when Al₂TiO₅ is dissolved in the slag. Al₂TiO₅ initially dissolves faster than the diffusion rate of the liquid product toward the bulk slag. With increasing reaction time, the boundary reaches its largest distance, the Al₂TiO₅ dissolution rate equals the liquid product diffusion rate, and the dissolution process remains stable until the inclusion is completely dissolved.     

Reduction of hysteresis losses in the magnetic refrigerant Gd5Ge2Si2 by the addition of iron

The magnetocaloric effect is the change in temperature of a material as a result of the alignment of its magnetic spins that occurs on exposure to an external magnetic field. The phenomenon forms the basis for magnetic refrigeration, a concept purported to be more efficient and environmentally friendly than conventional refrigeration systems. In 1997, a 'giant' magnetocaloric effect, between 270 K and 300 K, was reported in Gd5Ge2Si2, demonstrating its potential as a near-room-temperature magnetic refrigerant. However, large hysteretic losses (which make magnetic refrigeration less efficient) occur in the same temperature range. Here we report the reduction (by more than 90 per cent) of these hysteretic losses by alloying the compound with a small amount of iron. This has the additional benefit of shifting the magnetic entropy change peak (a measure of the refrigerator's optimal operating temperature) from 275 K to 305 K, and broadening its width. Although the addition of iron does not significantly affect the refrigerant capacity of the material, a greater net capacity is obtained for the iron-containing alloy when the hysteresis losses are accounted for. The iron-containing alloy is thus a much-improved magnetic refrigerant for near-room-temperature applications.     

Rapid solidification mechanism of Ag60Sb34Cu6 ternary alloy in drop tube

Ternary eutectic growth involves competitive nu-cleation and growth of three solids from one liquid. Thesolidification behavior of ternary eutectic alloy is morecomplex than that of binary eutectic alloy due to the addi-tion of the third component[1—4]. Up to now, most scientificinvestigations on ternary eutectic alloy focus on the influ-ence of changing the component or adding a fourth even afifth element on the performance of the alloy[5—8]. How-ever, the information on crystal growth char…     

Effect of different deformation and annealing procedures on non-magnetic textured Cu<Subscript>60</Subscript>Ni<Subscript>40</Subscript> alloy substrates

In this work, a series of specimens was prepared by the casting method. Sharp cube-textured substrates were processed by heavy cold rolling and recrystallization annealing (i.e., the rolling-assisted biaxially textured substrates (RABiTS) method). Both the rolling and the recrystallization texture in the alloy tapes were investigated by X-ray diffraction and electron back-scatter diffraction, respectively. The results showed that a strong copper-type deformation texture was obtained in the heavy cold-rolled substrate. In addition, the recrystallization annealing process was found to be very important for the texture transition in the Cu–Ni alloy substrates. The cube texture content in the Cu₆₀Ni₄₀ alloy substrates reached 99.7% (≤10°) after optimization of the cold-rolling procedure and the recrystallizing heat-treatment process, whereas the content of low-angle grain boundaries (from 2° to 10° misorientation) in the substrate reached 95.1%.     

非晶/微晶相变区硅基薄膜太阳能电池研究进展

综述了非晶/微晶相变区硅基薄膜的微观结构、光电特性及其在太阳能电池中的应用进展.稳定优质的宽带隙初始晶硅薄膜处于非晶/微晶相变区的非晶硅一侧,其相比于非晶硅具有更高的中程有序性和更低的光致衰退特性.低缺陷密度的窄带隙纳米晶硅薄膜处于非晶/微晶相变区的微晶硅一侧,有效钝化的纳米硅晶粒具有较高的载流子迁移率和较好的长波响应特性.基于上述相变区硅薄膜材料的叠层电池已经达到13.6%的稳定转换效率.掺锗制备的硅锗薄膜可进一步降低薄膜的带隙宽度,引入相变区硅锗合金薄膜后,三结叠层电池初始效率已经达到16.3%,四结叠层太阳能电池理论效率可以超过20%.     

Rolling-induced microstructure change in Zr_（65）Al_（7.5）Ni_（10）Cu_（12.5）Ag_5 bulk metallic glass

The microstructures and free-volume evolutions of as-cast and pre-annealed Zr65Al7.5Ni10Cu12.5Ag5 bulk metallic glasses during rolling deformation have been investigated. No phase transformation is detected in the as-cast/rolled specimen. However,the structural stability of the glass against plastic deformation is worse after pre-annealing,indicated by nanocrystallization in preannealed/rolled specimens with large deformation degrees. Moreover,with increasing deformation degree,the free-volume content in a pre-annealed/rolled specimen increases at a lower average rate than that in an as-cast/rolled specimen.     

Corrosion-wear behavior of nanocrystalline Fe88Si12 alloy in acid and alkaline solutions

The corrosion-wear behavior of a nanocrystalline Fe₈₈Si₁₂ alloy disc coupled with a Si₃N₄ ball was investigated in acid (pH 3) and alkaline (pH 9) aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe₈₈Si₁₂ alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe₈₈Si₁₂ alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe₈₈Si₁₂ alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si₃N₄ ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe₈₈Si₁₂ alloy in the pH 9 aqueous solution.     

First-principles calculations of the β′-Mg<Subscript>7</Subscript>Gd precipitate in Mg-Gd binary alloys

The metastable β’ phase is often the most effective hardening precipitate in Mg-Gd based alloys.In this paper,the structural,elastic and electronic properties of the recently identified β’-Mg7Gd precipitate in Mg-Gd binary alloys were investigated using first-principles calculations based on density functional theory.The lattice mismatches between the coherent β’-Mg7Gd precipitate and α-Mg matrix are discussed and used to rationalize the experimentally observed morphology of the precipitate.The mechanical properties were investigated through analysis of the single-crystal elastic constants and the polycrystalline elastic moduli.It is found that β’-Mg7Gd is brittle in nature.Strong covalent bonding in β’-Mg7Gd,as inferred from its electronic structure,further explains its mechanical properties.Our theoretical results show good agreement with experimental measurements.     

Electron density hole and quadruple structure of <Emphasis Type="Italic">B</Emphasis><Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> during collisionless magnetic reconnection

In collisionless reconnection,the magnetic field near the separatrix is stronger than that around the X-line,so an electron-beam can be formed and flows toward the X-line,which leads to a decrease of the electron density near the separatrix.Having been accelerated around the X-line,the electrons flow out along the magnetic field lines in the inner side of the separatrix.A quadruple structure of the Hall magnetic field By is formed by such a current system.A 2D particle-in-cell (PIC) simulation code is used ...