In vitro corrosion of Mg–1.21Li –1.12Ca –1Y alloy

The influence of the microstructure on mechanical properties and corrosion behavior of the Mg–1.21Li–1.12Ca–1Y alloy was investigated using OM, SEM, XRD, EPMA, EDS, tensile tests and corrosion measurements. The results demonstrated that the microstructure of the Mg–1.21Li–1.12Ca–1Y alloy was characterized by α-Mg substrate and intermetallic compounds Mg2 Ca and Mg24Y5. Most of the fine Mg2 Ca particles for the as-cast alloy were distributed along the grain boundaries, while for the as-extruded along the extrusion direction. The Mg24Y5 particles with a larger size than the Mg2 Ca particles were positioned inside the grains. The mechanical properties of Mg–1.21Li–1.12Ca–1Y alloy were improved by the grain refinement and dispersion strengthening. Corrosion pits initiated at the α-Mg matrix neighboring the Mg2 Ca particles and subsequently the alloy exhibited general corrosion and filiform corrosion as the corrosion product layer of Mg(OH)2and Mg CO3 became compact and thick.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Effect of homogenization process on the hardness of Zn–Al–Cu alloys

The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell “B” hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of the θ and τ' phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and temperature, used in their preparation.     

Effects of alloying and high-temperature heat treatment on the microstructure of Nb–Ti–Si based ultrahigh temperatur e alloys

The phase co mpositions, microstructure and especi ally phase i nterfaces in the as-cast and heat-treated Nb– Ti–Si based ultrahigh temperature alloys have been investigated. It is shown that β(Nb,X)5Si3 and γ(Nb,X)5Si3 are the primary p hase s in the Nb–22Ti–16Si–5Cr–5Al (S1) (at%) and Nb–20Ti–16Si–6C r–4Al–5Hf–2B–0.06Y (S2) (at% ) alloys, respectively. The Nb solid solution (Nbss) is the primary phase in Nb–22Ti–14Si–5Hf–3Al–1. 5B –0.0 6Y (S3) (at%) alloy . An orientation relationship between Nbss and γ(Nb,X)5Si3 was determine d to be (1-10)Nb//(101-0)γ and [111]Nb//[0001]γ in the as-cast S2 and S3 alloys. Some original β(Nb,X)5Si3 transfor med into α(Nb,X)5Si3 because Al and Cr diffused from the β(Nb,X)5Si3 to Nbss during heattreatment at 1500 °C for 50 h in the S1 alloy. Mean while, Ti diffused from Nbss to β(Nb,X)5Si3, which induced a Ti to generate near the interface between Nbss and Ti-rich β(Nb,X)5Si3. The orientation relationship between the newl y-formed a Ti and previous Nbss was (110 )Nb//(1-10-1) αTi and [001]Nb//(12-3-1)αTi. Among the ( Nb,X)5Si3 phases , the contents o f Cr and Al in β(Nb,X)5Si3 are n earl y the same as those in γ(Nb,X)5Si3 but obviously hi gher than those in the α(Nb,X)5Si3, where as the content of Si in α(Nb,X)5Si3 is nearly the same a s that in γ(Nb,X)5Si3 but higher than that in the β(Nb,X)5Si3     

Effect of benzaldehyde on the electrodeposition and corrosion properties of Ni–W alloys

The effect of different concentrations of benzaldehyde on the electrodeposition of Ni–W alloy coatings on a mild steel substrate from a citrate electrolyte was investigated in this study. The electrolytic alkaline bath (pH 8.0) contained stoichiometric amounts of nickel sulfate, sodium tungstate, and trisodium citrate as precursors. The corrosion resistance of the Ni–W-alloy-coated specimens in 0.2 mol/L H₂SO₄ was studied using various electrochemical techniques. Tafel polarization studies reveal that the alloy coatings obtained from the bath containing 50 ppm benzaldehyde exhibit a protection efficiency of 95.33%. The corrosion rate also decreases by 21.5 times compared with that of the blank. A higher charge-transfer resistance of 1159.40 Ω·cm2 and a lower double-layer capacitance of 29.4 μF·cm-2 further confirm the better corrosion resistance of the alloy coating. X-ray diffraction studies reveal that the deposits on the mild steel surface are consisted of nanocrystals. A lower surface roughness value (R_max) of the deposits is confirmed by atomic force microscopy.     

Effect of Zn addition on microstructure and mechanical properties of an Al–Mg–Si alloy

In the present work, an Al–0.66Mg–0.85Si–0.2Cu alloy with Zn addition was investigated by electron back scattering diffraction(EBSD), high resolution electron microscopy(HREM), tensile and Erichsen tests. The mechanical properties of the alloy after pre-aging met the standards of sheet forming. After paint baking, the yield strength of the alloy was improved apparently. GP(Ⅱ) zones and η’phases were formed during aging process due to Zn addition. With the precipitation of GP zones, β″ phases, GP(Ⅱ) zones and η’phases, the alloys displayed excellent mechanical properties.     

Corrosion behavior of Mg–Y alloy in NaCl aqueous solution

The corrosion behavior of Mg–(0.25, 2.5, 5, 8 and 15)Y alloys in 3.5wt.% NaCl aqueous solution was investigated. It was found that the degree of corrosion deterioration increased with increasing immersion time up to 2 h. Corrosion modes for the alloys with low and high content of Y element were general corrosion and pitting corrosion, respective ly, and the threshold content for the corrosion mode change was 2.5% for the tested alloys. The experimental results showed that the addition of Y refined the grain of the alloy, and the distribution, i.e., continuous or not, of the Mg24Y5 phases had great effect on the corrosion rate and corrosion mode.     

Effect of Mn content on the microstructure and mechanical properties of Mg–6Li–4Zn-xMn alloys

The as-cast Mg–6Li–4Zn-x Mn alloys were prepared and extruded at 280℃ with an extrusion ratio of 25:1. The effects of Mn content on the microstructure and mechanical properties of Mg–6Li–4Zn-x Mn alloys were investigated in this study. The XRD results show that Mg–6Li–4Zn–x Mn alloys consisted of α-Mg(hcp) + β-Li(bcc)duplex structured matrix, Mg Li₂Zn and Mn phases. The grains of the extruded Mg–6Li–4Zn–x Mn alloys were refined by dynamic recrystallization during the extrusion process...     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Effects of Zn content on the microstructure and the mechanical and corrosion properties of as-cast low-alloyed Mg–Zn–Ca alloys

The effects of Zn content on the microstructure and the mechanical and corrosion properties of as-cast low-alloyed Mg–xZn–0.2Ca alloys (x=0.6wt%, 2.0wt%, 2.5wt%, hereafter denoted as 0.6Zn, 2.0Zn, and 2.5Zn alloys, respectively) are investigated. The results show that the Zn content not only influences grain refinement but also induces different phase precipitation behaviors. The as-cast microstructure of the 0.6Zn alloy is composed of α-Mg, Mg₂Ca, and Ca₂Mg₆Zn₃ phases, whereas 2.0Zn and 2.5Zn alloys only contain α-Mg and Ca₂Mg₆Zn₃ phases, as revealed by X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses. Moreover, with increasing Zn content, both the ultimate tensile strength (UTS) and the elongation to fracture first increase and then decrease. Among the three investigated alloys, the largest UTS (178 MPa) and the highest elongation to fracture (6.5%) are obtained for the 2.0Zn alloy. In addition, the corrosion rate increases with increasing Zn content. This paper provides an updated investigation of the alloy composition–microstructure–property relationships of different Zn-containing Mg–Zn–Ca alloys.     

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl(x=1, 3 and 5) alloys

As-extruded Mg–5Sn–1Zn–xAl alloys(x=1, 3, and 5) were fabricated by hot extrusion. The experimental results revealed that the yield strength of alloys initially decreased and then increased with the increase of Al content. These changes were mainly attributed to the difference in crystallographic texture and volume fractions of second phases. The ultimate tensile strength, yield strength, and elongation of the alloys were greater than 310 MPa, 227 MPa, and 11%, respectively. The strain hardening ability of the alloys was also discussed.     

Optimization of dual effects of Mg– 1Ca alloys on the behavior of chondrocytes and osteoblasts in vitro

Mg ions can enhance the proliferation and redifferentiation of chondrocytes and the osteogenic differentiation of osteoblasts at specific concentrations, respectively. However, degradation of Mg alloys at varying degradation rates could lead to complex changes in the surrounding tissue environment, such as changes in the dynamic concentration of Mg ions and subsequent p H value. Considering the above mentioned factors, the comprehensive effects of Mg alloys on chondrocytes and osteoblasts behaviors have not yet been optimized. In this study, we evaluated the effects of Mg–1Ca microspheres on cell behavior with an aim to optimize conditions favorable for both cell types. Cells were cultured with Mg–1Ca microspheres prepared using the following concentrations: 250 μg/ml, 500 μg/ml and 1000 μg/ml. At specific time points,cytotoxicity, expression of specific genes and extracellular matrix deposition by cells(Alizarin Red Staining of osteoblasts and Alcian blue staining for chondrocytes) were evaluated. The experimental results revealed that Mg–1Ca microspheres prepared at a concentration of 250 μg/ml were optimum for both cell types, where chondrocytes were found to be in hypertrophy state while osteoblasts in close proximity to the microspheres showed osteogenetic differentiation. Interestingly, a slight change in osteoblasts behavior was observed nearer to and at a relative distance away from Mg–1Ca microspheres, an important observation for administering the application of microspheres as potential scaffolds.     

Effect of heat treatment on the microstructure of a Ni–Fe based superalloy for advanced ultra-supercritical power plant applications

The effect of heat treatment on the microstructure and microhardness of a Ni–Fe based superalloy for700 °C advanced ultra-supercritical coalfi red power plants was investigated. Results showed that the main phases in the alloy were γ, γ′, MC and M_23C_6, and no harmful phase was observed in the alloy.M_23C_6-type carbides discretely distributed nearby grain boundaries as the alloy was aged at above840 °C. The microhardness decreased with increasing aging temperature. The coarsening of γ′ led to the increment of microhardness at 780 °C and 810 °C for a short aging time, and a signi fi cant decrease in microhardness after aging at 840 °C. The aging temperature had more signi fi cant role on the microstructure than holding time. Therefore, to obtain optimum strengthening effect for this alloy, the aging temperature should not exceed 810 °C.     

Effect of rolling geometry on the mechanical properties,microstructure and recrystallization texture of Al–Mg–Si alloys

The effect of rolling geometry on mechanical properties, microstructure, and recrystallization texture of Al–Mg–Si alloys was studied by means of tensile tests, microstructural observations, and electron backscatter diffraction measurements. The results reveal that the elongation and the average plasticity strain ratio(r) values of the T4P(pre-aging plus natural aging)-treated alloy sheet with a rolling geometry value between 1 and 3 are somewhat higher than those of the T4P-treated sheet with a rolling geometry value between 3 and 6. The deformation and recrystallization microstructures of the sheet with a rolling geometry value between 1 and 3 are more uniform than those of the sheet with a rolling geometry value between 3 and 6. The former also possesses somewhat higher surface quality. H {001}110 and Goss {110}001 orientations are the main recrystallization texture components for the former case, whereas the latter case only includes H{001}110 orientation. Texture gradients are present in the two alloy sheets. Shear texture component F on the surface of the sheet with a rolling geometry value between 3 and 6 and its higher texture gradients have revealed that non-uniform deformation occurred during cold rolling. The effects of texture on the yield strength and r value were also discussed.     

Effects of hot compression deformation temperature on the microstructure and properties of Al-Zr-La alloys

The main goal of this study is to investigate the microstructure and electrical properties of Al-Zr-La alloys under different hot compression deformation temperatures. In particular, a Gleeble 3500 thermal simulator was used to carry out multi-pass hot compression tests. For five-pass hot compression deformation, the last-pass deformation temperatures were 240, 260, 300, 340, 380, and 420℃, respectively, where the first-pass deformation temperature was 460℃. The experimental results indicated that increasing the hot compression deformation temperature with each pass resulted in improved electrical conductivity of the alloy. Consequently, the flow stress was reduced after deformation of the samples subjected to the same number of passes. In addition, the dislocation density gradually decreased and the grain size increased after hot compression deformation. Furthermore, the dynamic recrystallization behavior was effectively suppressed during the hot compression process because spherical Al₃Zr precipitates pinned the dislocation movement effectively and prevented grain boundary sliding.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

Effects of solidifi cation cooling rate on the corrosion resistance of Mg – Zn–Ca alloy

This study was carried out to investigate the effect of solidification cooling rate on the corrosion resistance of an Mg–Zn–Ca alloy developed for biomedical applications. A wedge shaped copper mould was used to obtain different solidification cooling rates. Electrochemical and immersion tests were employed to measure the corrosion resistance of Mg–Zn–Ca alloy. It was found that increasing cooling rate resulted in a significant improvement in the corrosion resistance of the Mg–Zn–Ca alloy. The findings were explained in terms of solidification behaviour in association with the change in solubility of the alloying elements, microstructural homogeneity and refinement and chemical homogeneity as well as the increased cooling rates.     

Effect of ECAP temperature on microstructure and mechanical properties of Al–Zn–Mg–Cu alloy

The effect of equal channel angular pressing(ECAP) at different temperatures(room temperature, 120,150 and 180 °C) on microstructure and mechanical properties of Al-7075 solid solution alloy was investigated. Microstructure of the specimens was examined using orientation imaging microscopy,transmission electron microscopy as well as X-ray diffractometer, and mechanical properties were measured by Vickers microhardness and tensile tests. Microstructural investigations showed that after3 or 4 passes of ECAP, fi ne grains with average grain sizes in range of 300–1000 nm could be obtained at different ECAP temperatures. Increasing ECAP temperature from 120 to 180 °C caused a decrease in mechanical properties as a result of increasing grains and precipitates sizes, decreasing fraction of high angle boundaries and also transformation of η′ into η phase, while increasing ECAP temperature from RT to 120 °C leads to an increase in mechanical properties due to the formation of small η′ precipitates. So it can be concluded that ECAP process at 120 °C is the optimum process for attaining maximum mechanical properties. Quantitative estimates of various strengthening mechanisms revealed that the improvement of mechanical properties was mainly attributed to grain re fi nement strengthening, precipitation strengthening and dislocation strengthening.     

Effect of Zr and Ti on isothermal oxidation behavior of Nb–Si based alloys

The isothermal oxidation behavior of 56Nb-16Si-(20-x)Ti–3Cr–3Al-2Hf-xZr (x ?= ?0, 2, 5, 10 ?at. %) alloys was investigated at 800 ?°C and 1250 ?°C, respectively. The results show that increasing the Zr content evidently increased the oxidation rates at 800 ?°C, accompanied by the obvious occurrence of pesting oxidation. The alloys showed alike linear oxidation kinetics at 1250 ?°C. With the increase of Zr content, the adherence and integrity of oxide scales were improved, but the overall oxidation resistance was slightly deteriorated. The observed oxidation behavior may be attributed to the composition variation of Zr and Ti in the alloys. The oxidation mechanism associated with the composition variation is discussed in this study.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.