Isothermal section of ternary Sn-Zn-Ni phase equilibria at 250℃

Ternary Sn-Zn-Ni alloys were prepared and equilibrated at 250℃for 4-15 weeks.The phases formed in these equilibrated alloys were determined experimentally.The isothermal section of Sn-Zn-Ni system was constructed,based on the phase diagrams of the three constituent binary systems and the ternary phase equilibria data,determined in this study and referenced in literatures.12 single-phase regions were identified in the Sn-Zn-Ni ternary system at 250℃,including the three ternary compounds,δ,τ_1 andτ_2.There...     

Characterization and corrosion studies of ternary Zn–Ni–Sn alloys

Nine distinct zinc-nickel-tin films with different compositions have been galvanostatically electrodeposited. The films have been characterized by scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS). Their corrosion potentials and densities have been estimated using Tafel extrapolation. Next, the electrochemical behaviors of the films(deposited through the electrolytes containing 0, 6, 8, and10 g/L SnCl_2?6H_2O) have been examined based on cyclic voltammetry(CV) measurements. Further, these films have been immersed in 3.5 wt%Na Cl solution for 1 h, 1 d, 7 d, 14 d, 28 d, and 42 d followed by application of Tafel extrapolation and electrochemical impedance spectroscopy(EIS) tests on each aged sample. Finally, to analyze the morphologies and the compositions of the oxide films covering the surfaces of the 42-d aged films, FT-IR and SEM analyses have been performed. The results indicated that the Zn–Ni–Sn film produced through the bath including 6g/L SnCl_2?6H_2 O exhibits superior corrosion resistance because of the high Ni content in the presence of Sn that promotes the barrier protection capability of the deposit.     

Effect of niobium alloying level on the oxidation behavior of titanium aluminides at 850°C

This work addresses the alloying of titanium aluminides used in aircraft engine applications and automobiles. The oxidation resistance behavior of two titanium aluminides of α₂ + γ(Ti₃Al + TiAl) and orthorhombic Ti₂NbAl, recognized as candidates for high-temperature applications, was investigated by exposure of the alloys for 100 h in air. Thus, oxidation resistance was expressed as the mass gain rate, whereas surface aspects were analyzed using scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy, and the type of oxidation products was analyzed by X-ray diffraction and Raman spectroscopy. The orthorhombic Ti₂NbAl alloy was embrittled, and pores and microcracks were formed as a result of oxygen diffusion through the external oxide layer formed during thermal oxidation for 100 h.     

Oxidation behavior of the Fe-36Al-0.09C-0.09B-0.04Zr alloy at 1250°C

To explore and study the Fe-Al system alloy presenting exceptional oxidation resistance at high temperature, the Fe-36Al-0.09C-0.09B-0.04Zr alloy was designed and developed. The microstructure and hardness of the backing at 1250°C were analyzed and measured. Thermodynamics and kinetics of the oxidation behavior were also analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy techniques. The results show that the microstructure of the Fe-36Al-0.09C-0.09B-0.04Zr alloy is FeAl phase at ambient temperature and is stable at 1250°C. It displays the excellent property of oxidation resistance because the oxide film has only the Al₂O₃ layer, and its oxidation kinetics curve obeys the parabolic law at 1250°C. The oxidation mechanism at 1250°C is presumed that in the early oxidation period, the alloy oxidizes to form a large number of Al₂O₃ and a little Fe₂O₃, then, the enrichment of Al caused by Fe oxidization combines with O to form Al₂O₃.     

Effects of CeO2 on the XPS valence band spectra of coal under the combustion initialization stage at 400°C

In order to get the catalytic mechanism of CeO₂ on graphite and coal at 400°C, the morphologies of coal, graphite, and CeO₂ before and after combustion were analyzed through X-ray photoelectron spectroscopy (XPS). It is found that the particle size of coal is mostly between 11.727 and 64.79 μm, while the particle size of CeO₂ is between 1.937 and 11.79 μm. The agglomeration of coal and CeO₂ can be seen by scanning electron microscopy (SEM) after reaction. XPS results show that with the addition of CeO₂, the intensity of binding energy gets stronger, but there is no energy peak transition. Comparing the character of coal with and without the addition of CeO₂, it can be seen that the C-C bond fractures first at 400°C, while the C-H energy-band takes electrons at the same time to be far away from the Fermi level, and the O 2s, O 2p, and C sp hybrid orbitals are all excited. Adding CeO₂ can enhance the activity of the whole coal. In addition, through XPS analysis, combined with the oxygen transfer theory and the electron transfer theory, the catalytic mechanism of CeO₂ for pulverized coal combustion could be obtained.     

Corrosion behavior of ferritic ODS steel prepared by adding YH_2 nanoparticles in supercritical water at 600 °C

The corrosion behavior of the ferritic oxide dispersion strengthened(ODS)steel(14Cr-3Al-2W-0.1Ti)prepared by adding YH_2nanoparticles(NPs)was investigated in supercritical water(SCW)at 600°C for 1500 h.The mass gain of the ODS steel(215.5 mg/dm~2)was lower than that of SUS430 steel(357.2 mg/dm~2).A dual oxide layer generated on the surface of ODS steel after corrosion in SCW.The outer layer was composed of Fe_2O_3and Fe_3O_4,while the inner layer composed of the spinel-type FeCr_2O_4together with Al_2O_3.The generation of Y_2Ti_2O_7NPs in the ODS steel by adding YH_2NPs prohibits the formation of Y-Al-O particles and leaves more Al available to form a continuous protective oxide scale to improve the corrosion resistance.Moreover,the Y_2Ti_2O_7NPs act as efficient barriers to suppress the outward diffusion of metal atoms.This novel ODS steel shows potential applications in supercritical water.     

Effect of 5wt% Fe3O4 addition on the phase equilibria of the CaO-SiO2-TiO2 system at 1400 ℃ in air

The equilibrium phase relations of the CaO–SiO₂–Ti O₂–5wt%Fe₃O₄ system were experimentally investigated at 1400℃ in air High-temperature equilibration-quenching techniques were employed in an electric MoSi₂ resistance heated furnace,with phase composition analysis conducted using an electron probe microanalyzer and X-ray diffraction.A single liquid region,liquid–solid phase equilibria regions （including liquid–tridymite,liquid–rutile,liquid–perovskite,and liquid–wollastonite）,and three-phase equilibria regions of liquid–tridymite–rutile and liquid–rutile–perovskite were found.The 1400℃ isothermal sections of the CaO–SiO₂–Ti O₂–5wt % Fe₃O₄ system in air were projected.The present experimental results exhibited good agreement with the calculation results obtained from FactSage.     

Hot-corrosion behavior of Cr_2O_3–CNT-coated ASTM-SA213-T22 steel in a molten salt environment at 700°C

The present work investigates the hot-corrosion behavior of carbon nanotube(CNT)-reinforced chromium oxide coatings on boiler steel in a molten salt(Na_2SO_4–60 wt%V_2O_5) environment at 700°C under cyclic conditions. The coatings were deposited via the high-velocity oxygen fuel process. The uncoated and coated steel samples were subjected to hot corrosion in a silicon tube furnace at 700°C for 50 cycles. The kinetics of the corrosion behavior was analyzed through mass-gain measurements after each cycle. The corrosion products were analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray analysis techniques. The results revealed that uncoated steel suffered spallation of scale because of the formation of nonprotective Fe_2O_3 scale. The coated steel samples exhibited lower mass gains with better adhesiveness of oxide scale with the steel alloy until the end of exposure. The CNT-reinforced coatings were concluded to provide better corrosion resistance in the hot-corrosion environment because of the uniform dispersion of CNTs in the coating matrix and the formation of protective chromium oxides in the scale.     

In situ reaction mechanism of MgAlON in Al–Al_2O_3–MgO composites at 1700°C under flowing N_2

The Al–Al_2O_3–MgO composites with added aluminum contents of approximately 0wt%, 5wt%, and 10wt%, named as M_1, M_2, and M_3, respectively, were prepared at 1700°C for 5 h under a flowing N_2 atmosphere using the reaction sintering method. After sintering, the Al–Al_2O_3–MgO composites were characterized and analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that specimen M_1 was composed of MgO and MgAl_2O_4. Compared with specimen M_1, specimens M_2 and M_3 possessed MgAlON, and its production increased with increasing aluminum addition. Under an N_2 atmosphere, MgO, Al_2O_3, and Al in the matrix of specimens M_2 and M_3 reacted to form MgAlON and AlN-polytypoids, which combined the particles and the matrix together and imparted the Al–Al_2O_3–MgO composites with a dense structure. The mechanism of MgAlON synthesis is described as follows. Under an N_2 atmosphere, the partial pressure of oxygen is quite low; thus, when the Al–Al_2O_3–MgO composites were soaked at 580°C for an extended period, aluminum metal was transformed into AlN. With increasing temperature, Al_2O_3 diffused into AlN crystal lattices and formed AlN-polytypoids; however, MgO reacted with Al_2O_3 to form MgAl_2O_4. When the temperature was greater than(1640 ± 10)°C, AlN diffused into Al_2O_3 and formed spinel-structured AlON. In situ MgAlON was acquired through a solid-solution reaction between AlON and Mg Al_2O_4 at high temperatures because of their similar spinel structures.